J.E. Adams 8670 Series Manual de usuario

8670 SERIES MANUAL

TABLE OF CONTENTS

PRODUCT INFORMATION………………………………………………. 3

SPECIFICATIONS…………………………………………………………. 4

IMPORTANT SAFETY INSTRUCTIONS……………………………….. 5

INSTALLATION INFORMATION………………………………………... 5-6

GENERAL INFORMATION………………………………………………………………………. 5

WIRING INFO……………………………………………………………………………………… 6

MOUNTING DIMENSIONS………………………………………………………………………. 6

TIMER SETUP…………………………………………………………….... 7-10

SSAC SETUP………………………………………………………………………………………. 7

INFITEC SETUP…………………………………………………………………………………… 8

TIMER SETTINGS CHART………………………………………………………………………. 9

TYPICAL TIMER SETTINGS…………………………………………………………………….. 10

MAINTENANCE……………………………………………………………. 11

PARTS BREAKDOWN…………………………………………………….. 12-13

AIR MACHINE & WATER………………………………………………………………………… 12

REEL BASE………………………………………………………………………………………… 13

SCHEMATICS………………………………………………………………. 14-15

8670 SERIES WITH SSAC……………………………………………………………………… 14

8670 SERIES WITH INFITEC ASCR54………………………………………………………. 15

BASIC TROUBLESHOOTING…………………………………………... 16

8670 SERIES MANUAL 8/4/10

PRODUCT INFORMATION

Please take a moment to fill out the information below in order to aid us with any future sales or

service inquiries. Model number and serial number information can be found on the serial tag

located inside the control box and/or on the lower exterior of the can. Key number can be found

on the tag that comes attached to the keys. There may be more than one key number depending

on unit.

Please keep this information with your records.

MODEL#:_________________________________________

SERIAL#:_________________________________________

KEY NUMBER(S):_________________________________

DATE PURCHASED:_______________________________

DISTRIBUTOR:___________________________________

J.E. Adams Industries

1025 63rd Ave. S.W.

Cedar Rapids, IA 52404

1-800-553-8861

www.jeadams.com

SPECIFICATIONS:

Unit specifications:

Voltage: 120v, 60Hz

Amperage: (1) 20 amp service for air/water or air only.

(1)10 amp service for air/water or air only “Only on units which in include

the letters TT OR G in model #. (Example 8670-2TTA or 8670-2GA). Do

not attempt to hook other models up in this fashion. Instant failure will

occur.

Weight: 155-175 lbs with pallet attached

____________________________________________________________________________________

Air specifications:

Compressor: Dependant on Model # ordered

Thomas 120vac@60hz, ¾ hp twin head

Thomas 120vac@60hz, ¾ hp- non twin head

Devilbiss 120vac@60hz, 1 ½ hp

Gast 120vac@60hz, ¾ hp- twin head

Timer: SSAC and Infitec ASCR54

__________________________________________________________________________________________________

Water specifications:

Solenoid: 120vac@60hz

__________________________________________________________________________________________________

NOTE: “UNIT INTENDED FOR COMMECIAL USE ONLY”

Duty cycle: 4 minutes run time- max

4minutesofftime

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE)

WARNING – To reduce the risk of fire, electric shock, or injury:

Use only as described in manual. Use only manufactures recommended attachments.

Do not allow to be used as a toy. Close attention is necessary when used by or near children.

Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

Never use air nozzle for anything other than for its intended use.

SAVE THESE INSTRUCTIONS

Installation Instructions:

Determine location to mount unit (“DANGER” “THIS EQUIPMENT INCORPORATES PARTS SUCH AS

SWITCHES, MOTORS, OR THE LIKE THAT TEND TO PRODUCE ARCS OR SPARKS THAT CAN CAUSE AN

EXPLOSION. WHEN LOCATED IN GASOLINE-DISPENSING AND SERVICE STATIONS INSTALL AND USE

AT LEAST 20 FEET (6 M) HORIZONTALLY FROM THE EXTERIOR ENCLOSURE OF ANY DISPENSING PUMP

AND AT LEAST 18 INCHES (450 MM) ABOVE A DRIVEWAY OR GROUND LEVEL.”

Run service to that location

Grounding Instructions: This appliance must be connected to a grounded metal, permanent wiring system; or an

equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding

terminal or lead on the appliance.

See next page for bolt pattern.

AIR MACHINE MOUNTING DIMENSIONS

Figure 3: SSAC timer setup

Figure 3 shows an SSAC timer set for 1 coin to start and 3.8

minutes per coin for a total run time of 3.8 minutes (3 minutes

and 48 seconds).

TIMER SETUP – SSAC TIMERS

Note: “AE” and “AN” model SSAC timers are accumulating

timers. During use, timing can be extended proportionately

by adding more coins.

The SSAC timer has two adjustable settings: Time per coin (in

minutes) and number of coins to start.

Time per coin:

Time per coin is the amount of time the unit will run per coin

inserted and can be set from 0.1 minutes (6 seconds) to 12.7

minutes (12 minutes and 42 seconds) in increments of 6 seconds

by turning on the correct switches until their values equal the

desired time.Refer to Tables 2 and 3 (pages 11-12) for standard

timer and coin settings. For custom settings, follow the steps

below:

1. Figure the total time your vac will run (in minutes) and divide

that number by the number of coins to start. This is your

time per coin. Round up or down to the nearest tenth of a

minute.

2. Subtract the largest value switch (initially 6.4) from your time

per coin.

a. If the resulting number is zero, move the switch to

the “on” position and set all remaining un-set switches

in the “off” position. Your timer is now set.

b. If the resulting number is positive, move the switch

into the “on” position. Using the resulting number as

your new time per coin, repeat step 2 with the next

largest switch value.

c. If the resulting number is negative, set the switch in

the “off” position and repeat step 2 using the next

largest switch value.

Coins to start:

Coins to start is the amount of coins needed to activate the

timer and can be set from one to seven coins in increments of

one coin. Refer to Table

2 (page 10) for switch settings

TIMER SETUP – INFITEC TIMERS

The Infitec timer has two adjustable settings: Total run time

(in seconds) and number of coins to start.

Total run time:

Total run time is the amount of time the unit will run

once activated and can be set from 1 second to 1023 seconds

(17 minutes and 3 seconds) in increments of 1 second by

turning on the correct switches until their values equal the

desired time.Refer to Tables 2 and 3 (pages 11-12) for

standard timer and coin settings. For custom settings, follow

the steps below:

1. Figure the total time your vac will run (in seconds).

This is your total run time. Round up or down as

desired.

2. Subtract the largest value switch (initially 512) from

your total run time.

a) If the resulting number is zero, move the

switch to the “on” position and set all remaining

un-set switches in the “off” position. Your timer

is now set.

b) If the resulting number is positive, move the

switch into the “on” position. Using the

resulting number as your new time per coin,

repeat step 2 with the next largest switch value.

c) If the resulting number is negative, set the

switch in the “off” position and repeat step 2

using the next largest switch value.

Coins to start:

Coins to start is the amount of coins needed to activate

the timer and can be set from one to 15 coins in

increments of one coin. Refer to Table 2 (page 10) for

switch settings.

60 (1 min)

100

110

120 (2 min)

130

140

150

160

170

180 (3 min)

190

200

210

220

230

240 (4 min)

250

260

270

280

290

300 (5 min)

1xxxxxx

2xx xx xxxxxxxxxxxxxx

4x xx x x xxx xx xx xx xx xx x

8xx xx xx x x xx x x xx x x xx x

16 xxx xxx xx x x xx xx xx x

32 xxxxxx xxx xxxx xxx xx

64 xxxxxx xxxxxx

128 xxxxxxxxxxxxx

256 xxxxx

512

0.1 (6sec)

0.2 (12 sec)

0.3 (18 sec)

0.4 (24 sec)

0.5 (30 sec)

0.6 (36 sec)

0.7 (42 sec)

0.8 (48 sec)

0.9 (54 sec)

1.0

1.1

1.2

1.3

1.4

1.5

1.6

1.7

1.8

1.9

2.0

2.5

3.0

3.5

4.0

4.5

5.0

5.5

6.0

6.5

7.0

7.5

8.0

8.5

9.0

9.5

10.0

0.1 xxxxxxxxxxxxxxxxxx

0.2 xx xx xx xx xx xx xx xx xx

0.4 xxxx xxxx x x x xx x x xx

0.8 xxxxxxxx xx xx x x xx

1.6 xxxxxxx xxx xxxx

3.2 xxxxxx x

6.4 xxxxxxxx

1xxxxxxxx

2xx xx xx xx

4xxxx xxxx

8xxxxxxxx

All Timers

Coin Switches

Coins to Start

SSAC Timers

Timer Switches

Time Per Coin (In minutes)

Infitec Timers: Total Run Time (In Seconds)

Infitec and IDX Timers

Timer Switches

IDX Timers: Time Per Coin (In Seconds)

Table 2: Timer Settings Chart

Note: “X” indicates a switch in the “on” position

Amount to

Start Total Run

Time Switches in "On"

Position Amount to

Start Total Run

Time Switches in "On"

Position Amount to

Start Total Run

Time Switches in "On"

Position

25¢ 2 MIN 8, 16, 32, 64 25¢ 2 MIN 0.4, 1.6 25¢ 2 MIN 8, 16, 32, 64

25¢ 2-1/2 MIN 2, 4, 16, 128 25¢ 2-1/2 MIN 0.1, 0.8, 1.6 25¢ 2-1/2 MIN 2, 4, 16, 128

25¢ 3 MIN 4, 16, 32, 128 25¢ 3 MIN 0.2, 0.4, 0.8, 1.6 25¢ 3 MIN 4, 16, 32, 128

25¢ 3-1/2 MIN 2, 16, 64, 128 25¢ 3-1/2 MIN 0.1, 0.2, 3.2 25¢ 3-1/2 MIN 2, 16, 64, 128

25¢ 4 MIN 16, 32, 64, 128 25¢ 4 MIN 0.8, 3.2 25¢ 4 MIN 16, 32, 64, 128

25¢ 4-1/2 MIN 2, 4, 8 , 256 25¢ 4-1/2 MIN 0.1, 0.4, 0.8, 3.2 25¢ 4-1/2 MIN 2, 4, 8, 256

25¢ 5 MIN 4, 8, 32, 256 25¢ 5 MIN 0.2, 1.6, 3.2 25¢ 5 MIN 4, 8, 32, 256

25¢ 5-1/2 MIN 2, 8, 64, 256 25¢ 5-1/2 MIN 0.1, 0.2, 0.4, 1.6, 3.2 25¢ 5-1/2 MIN 2, 8, 64, 256

50¢ 2 MIN 4, 8, 16, 32 50¢ 2 MIN 0.2, 0.8 50¢ 2 MIN 8, 16, 32, 64

50¢ 2-1/2 MIN 4, 8, 64 50¢ 2-1/2 MIN *50¢ 2-1/2 MIN 2, 4, 16, 128

50¢ 3 MIN 2, 8, 16, 64 50¢ 3 MIN 0.1, 0.2, 0.4, 0.8 50¢ 3 MIN 4, 16, 32, 128

50¢ 3-1/2 MIN 2, 8, 32, 64 50¢ 3-1/2 MIN *50¢ 3-1/2 MIN 2, 16, 64, 128

50¢ 4 MIN 8, 16, 32, 64 50¢ 4 MIN 0.4, 1.6 50¢ 4 MIN 16, 32, 64, 128

50¢ 4-1/2 MIN 8, 128 50¢ 4-1/2 MIN *50¢ 4-1/2 MIN 2, 4, 8, 256

50¢ 5 MIN 2, 4, 16, 128 50¢ 5 MIN 0.1, 0.8, 1.6 50¢ 5 MIN 4, 8, 32, 256

50¢ 5-1/2 MIN 2, 4, 32, 128 50¢ 5-1/2 MIN *50¢ 5-1/2 MIN 2, 8, 64, 256

75¢ 2 MIN 8, 32 75¢ 2 MIN *75¢ 2 MIN 8, 16, 32, 64

75¢ 2-1/2 MIN 2, 16, 32 75¢ 2-1/2 MIN *75¢ 2-1/2 MIN 2, 4, 16, 128

75¢ 3 MIN 4, 8, 16, 32 75¢ 3 MIN 0.2, 0.8 75¢ 3 MIN 4, 16, 32, 128

75¢ 3-1/2 MIN 2, 4, 64 75¢ 3-1/2 MIN *75¢ 3-1/2 MIN 2, 16, 64, 128

75¢ 4 MIN 16, 64 75¢ 4 MIN *75¢ 4 MIN 16, 32, 64, 128

75¢ 4-1/2 MIN 2, 8, 16, 64 75¢ 4-1/2 MIN *75¢ 4-1/2 MIN 2, 4, 8, 256

75¢ 5 MIN 4, 32, 64 75¢ 5 MIN *75¢ 5 MIN 4, 8, 32, 256

75¢ 5-1/2 MIN 2, 4, 8, 32, 64 75¢ 5-1/2 MIN *75¢ 5-1/2 MIN 2, 8, 64, 256

$1.00 2 MIN 2, 4, 8, 16 $1.00 2 MIN 0.1, 0.4 $1.00 2 MIN 8, 16, 32, 64

$1.00 2-1/2 MIN 2, 4, 32 $1.00 2-1/2 MIN *$1.00 2-1/2 MIN 2, 4, 16, 128

$1.00 3 MIN 4, 8, 32 $1.00 3 MIN *$1.00 3 MIN 4, 16, 32, 128

$1.00 3-1/2 MIN 2, 4, 16, 32 $1.00 3-1/2 MIN *$1.00 3-1/2 MIN 2, 16, 64, 128

$1.00 4 MIN 4, 8, 16, 32 $1.00 4 MIN 0.2, 0.8 $1.00 4 MIN 16, 32, 64, 128

$1.00 4-1/2 MIN 4, 64 $1.00 4-1/2 MIN *$1.00 4-1/2 MIN 2, 4, 8, 256

$1.00 5 MIN 4, 8, 64 $1.00 5 MIN *$1.00 5 MIN 4, 8, 32, 256

$1.00 5-1/2 MIN 4, 16, 64 $1.00 5-1/2 MIN *$1.00 5-1/2 MIN 2, 8, 64, 256

IDX TIMER SETTINGS SSAC TIMER SETTINGS INFITEC TIMER SETTINGS

Table 3: Typical Timer Settings

Note: “*” denotes a configuration that is not possible with this timer. See Table 2 for the closest approximation to

this time

Tabla de contenidos

Manuales populares de Compresor de aire de otras marcas

Sparmax

Sparmax DC-25XR Manual de usuario

KAESER

KAESER M122 Manual de usuario

GMC

GMC GAC1500 Manual de usuario

Briggs & Stratton

Briggs & Stratton Air Compressor Manual de usuario

Fini

Fini F3GST2TK Manual de usuario

Industrial Air

Industrial Air CP1580325 Manual de programación

Campbell Hausfeld

Campbell Hausfeld RP3300 Guía de inicio rápido

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Manual de usuario

Hitachi

Hitachi EC99S Manual del operador

Parkside

Parkside PKO 270 A1 Manual de usuario

Sullair

Sullair 185 Manual de usuario

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Manual de usuario

Ferm

Ferm CRM1046 Manual de usuario

BE AC153 Manual de usuario

RIDGID

RIDGID OF25150A Manual de usuario

Johnson Controls

Johnson Controls QUANTUM LX Manual

Sears

Sears Craftsman 919.167463 Manual de usuario

Ring Automotive

Ring Automotive RAC700 Manual de usuario