J D Williams PD479 Manual de usuario
SOLAR LED STAKE LIGHTS
Assembly Instructions - Please keep for future reference PD479, PD481,PD482
Important – Please read these instructions fully before starting assembly
IMPORTANT - This product has been designed for non-professional,
domestic use only.
IMPORTANT - Dispose of all packaging correctly and responsibly and
in accordance with all local laws and regulations. Never leave packag-
ing components within reach of children as they can be a source of
danger.
IMPORTANT - Carefully unpack and examine the product for any
damage. If you think there is a defect, do not use the product
IMPORTANT - This is a class 3 product low voltage product , battery
powered and not request power supply connection.
WARNING - Do not modify or alter any product before or after installa-
tion. This may render the product unsafe.
WARNING - This product is not intended for use by persons (including
children) with reduced physical, sensory and mental capabilities, or
lack of experience and knowledge, unless they have been given super-
vision or instruction concerning use of the product by persons responsi-
ble for their safety.
WARNING - Children should be supervised to ensure that they do not
play with the product.
Safety Information
BATTERY SAFETY INFORMATION
• Do not dismantle, open or shred the battery.
• Do not expose the battery to heat or fire.
• Avoid storage in direct sunlight.
• Do not short-circuit the battery.
• Do not subject the battery to mechanical shock.
• Keep the battery out of the reach of children.
• Keep the battery clean and dry.
• Do not leave a battery on prolonged charge when not in use.
BATTERY CAUTION
The rechargeable battery used in this device may present a risk of
fire or chemical burn if mistreated. Do not Disassemble, short circuit,
crush, expose to heat above 60°C or incinerate.
INSTALLATION
1
Installation
Dia.1.
1. Un-screw the top section of the fitting.
2. Turn on the on/off switch.
3. Re-screw the top section of the fitting.
4. Attach the pole to the fitting as illustrated.
5. Remove the spike from the pole.
6. Attach the spike to the pole in the posi-
tion illustrated.
7. Place the fitting on the required position
and test.
The LED light only can operate under a dark
atmosphere.
Battery Replacement (If required).
Dia.02.
1. Un-screw the top section of the fitting.
2. Using screw driver (not supplied)
un-screw the screws from the battery
compartment.
3. Open the battery compartment and
remove the old battery.
4. Insert new battery and closed the
battery compartment.
5. Re-screw all the screws from the battery
compartment
6. Re-screw the top section of the fitting.
This product is suitable to use Nickel metal
Hybrid battery, abbreviated NI-MH, any
other batteries type are not accepted.
Cleaning
- Use a clean dry soft or slightly damp cloth.
- Do not use abrasive cloths or polishes as this may
cause damage to the product.
APPROVED
06/11//2019
ISSUE 1
Q.C
Maintenance
PD479, PD481,PD482
J D Williams & Company Limited is part of N Brown Group plc. Griffin House, 40 Lever Street, Manchester, M60 6ES
Dia.1
Dia.2
2
34
5
6
7
Este manual sirve para los siguientes modelos
2
Otros manuales de Luz exterior de J D Williams
Manuales populares de Luz exterior de otras marcas
Lindby
Lindby 9949029 Manual de usuario
HEPER
HEPER DOGO Side LW6048.585-US Instrucciones de instalación y funcionamiento
HEPER
HEPER LW8034.003-US Instrucciones de instalación y funcionamiento
Maretti
Maretti VIBE S 14.6080.04.A Manual de usuario
BEGA
BEGA 84 253 Manual
HEPER
HEPER MINIMO Instrucciones de instalación y funcionamiento
LIGMAN
LIGMAN BAMBOO 3 Manual de usuario
Maretti
Maretti TUBE CUBE WALL 14.4998.04 Manual de usuario
Maxim Lighting
Maxim Lighting Carriage House VX 40428WGOB Manual de usuario
urban ambiance
urban ambiance UQL1273 Manual de usuario
TotalPond
TotalPond 52238 Manual de usuario
Donner & Blitzen
Donner & Blitzen 0-02661479-2 Manual de usuario