J.ASSY VISUM Monitor Manual de usuario

OPERATOR’SOPERATOR’S

MANUALMANUAL

version 4.2

100 Yellow | 25 Magenta 100 Black

Manual

v. 4.2

Product

v. 3.1

Visum Monitor Software

v. 4.4 - 5.0

Manual

v. 4.2

Product

v. 4.0

Visum Fertilizer Software

-----

VISUM MONITOR | VISUM FERTILIZER

This device contains FCC ID 2AD66-RF2401F20

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received,

including interference that may cause undesired operation.

For further information, please visit www.fcc.gov.

This device contains IC ID 21278- RF2401F20

IC compliance

This device complies with Industry Canada license-exempt

RSS standard(s).

Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including

interference that may cause undesired operation

of the device.

Conformité aux normes d’IC

Cet appareil est conforme à la(aux) norme(s) RSS sans

licence d’Industry Canada.

Son utilisation est soumise aux deux conditions suivantes:

(1) Cet appareil ne doit pas causer d’interférences et

(2) Il doit accepter toutes interférences reçues, y compris

celles susceptibles d’avoir des effets indésirables

sur son fonctionnement.

Table of Contents

100 Yellow | 25 Magenta 100 Black

Specications .......................................................... 04

Visum Monitor ........................................................ 04

Visum Fertilizer....................................................... 04

Installation................................................................ 05

Visum Monitor ........................................................ 05

Visum Fertilizer....................................................... 06

Recommendations ................................................. 07

Power Connection................................................... 08

Connecting to a power plug inside of

the tractor cab........................................................ 08

Connecting to the tractor battery........................... 08

Attach the antenna................................................. 09

Network ID ............................................................... 10

Operation ................................................................. 12

Functions description ............................................. 14

Version 5.0 or below............................................... 14

F1 | List sensors ..................................................... 14

F2 | Beep volume ................................................... 15

F3 | Brightness ....................................................... 15

F4 | Check Address................................................ 15

F5 | Add sensors .................................................... 16

F6 | Show Monitor ID.............................................. 16

F7 | Maneuver beep delay...................................... 17

Troubleshooting table ............................................. 18

Cleaning and Storage.............................................. 20

Warranty ................................................................... 20

Discarding ................................................................ 21

| J.Assy

Operation Instructions

Specifications

Radiofrequency communication at 2.4GHz.

GFSK Modulation.

Omni-directional antenna, 5dBi, 50 Ohms.

SMA connector.

Supply voltage: 10Vdc to 30Vdc.

Display with 2 character, 7 segments.

2 Red/Green/Orange LEDs.

Resistant to dust and water splash.

100 Yellow | 25 Magenta 100 Black

Specifications

Resistant to dust and water jet.

Radiofrequency communication at 2.4GHz.

GFSK Modulation.

Internal antenna.

Dimension: 71mm (A) x 89mm (L).

Weight: 245g.

Internal diameter of the sensor: 45mm.

Wearing protection: Stainless Steel.

Outer diameter of the hose:

from 1 1⁄4 to 2 1⁄16”.

100 Yellow | 25 Magenta 100 Black

OPERATOR´S MANUAL | Visum Monitor | Visum Fertilizer | 5

ATTENTION:

• The Monitor should be installed with the

antenna in a vertical line, and should be avoid

putting the antenna in the horizontal position.

• The Monitor should be installed with the best

possible line of sight to the sensors in order to

avoid communication problems.

• Avoid installing the monitor close to the cab

ROPS column. Keep a minimum distance of

12 in. between monitor and column.

Installation | Visum Monitor

1. Disassemble the bracket of the Monitor, removing the two

side nuts.

2. Clean the installation surface with a cloth and alcohol.

3. Remove the lm from the double-sided tape and fasten the

bracket to the surface by pressing the whole area of the tape.

4. Wait for 15 minutes and then mount the Monitor on the

bracket with the two side nuts.

5. If you install the bracket over a glass surface, put the anti-

UV tape on the opposite side of the glass in order to protect

the double-sided tape from the sun.

6. Press the button to turn on the Monitor and hold it for

5 seconds to turn it off.

Alternatively, the tape may be removed to mount the bracket

with screws or attached to a bar with clamps or RAM Mount

kit (not included).

| J.Assy

The sensor is installed between the diffuser/air release and the

fertilizer outlet hose:

Installation | Visum Fertilizer

”

4”2”4”3”162

Choose the correct inlet and outlet coupler

for the hose and diffuser diameters.

ASSEMBLY

1. Cut a piece of the hose at the diffuser side with the

length of the sensor-coupler assembly, so that the

total length will be the same as the original hose.

2. Place the sensor with the

internal antena facing “up”

or “skyward”. The internal

antenna is located to the left

of the square patch with “P”

and “L” between the “J” and

“A” of the word J. Assy. See

illustration below.

TIP:

• Do not bend the couplers to install

in your system. That can increase

clogging or release during use.

TIP:

• Do not install the sensor

at. This will cause sensor

wake up issues.

OPERATOR´S MANUAL | Visum Monitor | Visum Fertilizer | 7

1. Diffuser, 2. Inlet coupler, 3. Outlet coupler, 4. Metal clamps, 5. Hose.

Sensor Assembly

3. Securely fasten the rubber couplers with the metal clamps1.

Do not “overtighten”. Check the hose clamps after

10 minutes of eld operation to ensure everything is snug

and maintaining good connections.

TIP:

• Do not point or align the sensor antenna

toward a metal barrier, that could degrade

the communication efciency from the sensor

to the monitor.

4”2”4”3”162

1 2 3 4 5

Recommendations

11, 75 em - 2, 75 em x 0312 em x 0021 in.

ATTENTION:

• Do not install the sensor upside down.

Installation must match the orientation in the

pictures below.

Flow DirectionFlow Direction

| J.Assy

CONNECTING TO THE TRACTOR BATTERY

• Use the included installation kit is detailed below.

2a 2b

2c 2d

1a. The installation kit will

not be used, but a proper

manufacturer harness (not

included) will be needed.

1b. Cut the power cable

excess and mend the wires

with the manufacturer

harness.

CONNECTING TO A POWER PLUG INSIDE OF THE

TRACTOR CAB

The power cable must be connected to 12Vdc to 24Vdc

power source.

Power Connection

OPERATOR´S MANUAL | Visum Monitor | Visum Fertilizer | 9

ATTENTION:

• Do not disconnect any others cables attached

to the battery of the tractor. It may affect the

functionality of other electronics in the tractor.

• The red connector must be protected with self-fusing tape.

• Preferably, the power cable should be connected directly

to the battery terminals.

ATTACH THE ANTENNA

• You will nd the antenna inside your

Monitors box.

• Attach it to the back of the Monitor

by threading on the connection.

Do not “over-tighten”.

• Position the antenna so that it is in

a vertical orientation.

| J.Assy

Network ID

All sensors must be congured with the network ID in

order to communicate with the Monitor. The network ID

can be found in the back of the Monitor or can be extract

by software operation. The sensor conguration can be

done with a Visum Monitor. Check how it can be done on

this manual.

The following steps must be done:

1. Find the address indicator on the rubber cover

(square with “P” and “L” and numbers).

2. Wake up the sensor by shaking it.

3. Place the magnet on the address indicator

(make circular movement to easily turn on the

internal switch).

4. Wait for the conrmation beep or message.

5. Fill the address indicator with the number of

the implement and row.

ATTENTION:

• Never congure two sensors at the same

time, even with two different devices, because

the connections may cross each other.

TIP:

1. In order to change the address of any

sensor, just follow the steps again.

2. Before doing the sensor “addressing

procedure”, watch videos on Youtube by

J.Assy (video Visum Monitor).

3. When installing the sensors on your machine

initially, we recommend you “address” the

sensors to the monitor on your

workbench rst before installing the

sensors on the toolbar row units.

Otros manuales para VISUM Monitor

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación