Itotec Robocut RC-100DX Manual de usuario
PAPER GUILLOTINE
Type No.
INSTRUCTION MANUAL
Read this instruction manual carefully and understand the contents thoroughly before
starting operation, inspection and maintenance or servicing of this product.
The operator and supervisor for this product must not have any person who does not
understand the contents of this product operate this machine.
2
Table of Contents
Foreword ·····················································································
Safety Precautions······································································
Warning Label ·············································································
Introduction
Main Body Front Panel································································
Main Body Rear Panel ································································
Operation Panel ··········································································
Operation Panel Right Side·························································
Knife Button Panel·······································································
Parts Identification &
Function
Backgauge Right & Left Adjustment ···········································
Backgauge Upper & Lower Adjustment ······································
Clamp Pressure Adjustment ·······················································
Confirmation of knife height ························································
Knife Height Adjustment······························································
To Determine Knife Angle ···························································
Type of Knife················································································
To Replace Cutting stick······························································
How to change the safety bolt ·····················································
How to install the back plate ·······················································
How to read information display ··················································
Adjustment Method
Operation Method Introduction ·················································································
To Operate Cutting button ···························································
To Operate Backgauge ·······························································
To Change Backgauge Speed ····················································
To Change Unit ···········································································
To Correct Exact Size & Indicated Size Errors····························
To Call Course·············································································
To Call Empty Course ·································································
To Erase Course ·········································································
To Call Page················································································
To Insert Page ·············································································
To Delete Page············································································
To Use Cut line device ································································
To Use Air Table ··········································································
How to show counter display·······················································
17
4
5
8
10
9
12
12
14
16
18
19
20
20
21
26
27
28
29
30
31
32
33
34
35
36
37
38
39
6
22
23
24
25
How to show counter display
40
3
Table of Contents
Memroy Method (Memory Method by Ten-key)··························
Memory Method (Memory Method by Backgauge)·····················
Memory Method (Memory Method by Cutting) ···························
Push-out Method·········································································
Stacking position Method ····························································
How to perform soft clamp setting···············································
How to set the clamp pressure····················································
How to set the clamp timer··························································
Memory &
Setting Method
Knife Replacement
Method
How to remove the knife······························································
How to install the knife ································································
How to remove the knife (for models with a knife lifter)···············
How to install the knife (for models equipped with a knife lifter)
Oil Changing Method Hydraulic Oil Change ··································································
Replacement of gear oil ······························································
Lubrication and Greasing-up·······················································
Oil Table ······················································································
62
42
44
56
58
46
Applied Operation
Method
Expell Air Method ········································································
Full-Automatic Operation Method················································
To Copy Data···············································································
To Use Calculation Function ·······················································
To Use Spare Course··································································
To Save Plural Jobs Inside Course ·············································
To Use Hold Feed Key and Number of Repetition Key················
50
52
54
55
Repair Service &
Specifications
Repair Service ············································································
Specifications ··············································································
66
43
67
59
45
53
51
54
47
48
49
64
68
70
71
69
4
● This manual is a guide book for using this product safely.
● Before using this product, be sure to read this manual and thoroughly understand the
operation, checkup or inspection and maintenance or servicing.
● Operation or the like that is different from the description given in this manual, if performed,
may lead to serious accidents resulting in death or injury.
● In various portions in this manual, a description is given of the precautions as indicated
below.
These indications are the precautions for maintaining operational safety in particular.
Upon thorough understanding, you are requested to start operations work.
Introduction
Foreword
WARNING
If this machine is used carelessly, serious injury or serious disasters
or accidents may occur.
The operator and maintenance personnel should read this manual carefully
before starting operation or maintenance work for this machine.
This manual should be kept handy near the machine always for easier
reference.
The machine should not be operated or maintained before this manual can
be understood perfectly.
Where this manual was lost or damaged, contact our company or our local
agent immediately for ordering.
If this product is transferred, be sure to attach this manual therewith and
transfer this product to the subsequent owner.
5
Cutting materials, such as paper, may frequently be stacked near or around the machine; it is, therefore,
necessary to pile up those materials firmly and take care not to suffer from a disaster by stumbling or
bumping.
Do not put the machine in a place exposed to rain and an extremely moist place. Also, avoid using the
machine in a wet state.
Do not use the machine where combustible liquid and gas are present nearby.
Keep any infant and children away from the machine.
Since extremely high precision is required for cutting operations work as well as operational safety, it is
necessary to provide adequate lighting that is not flickering or dazzling.
Since paper powder scatters around during operations work, it is necessary to give care to ventilation
and draft as well.
● Transportation, Setup and Installation
This product is transported by local agen`s appointed carrier, and representative engineer is responsible
for setup and installation of this product.
It is, however, necessary to always ask the firm having the electric work engineer licence for electric
works.
For electrical capacity, see the "Specifications" paragraph on page.
To move and transfer this product, contact our representative.
● Repair Service
If an abnormal condition should be found in the machine,contact our loacal agent.
Do not use the machine until the abnormality is recovered.
Safety Precautions
Introduction
● Environment in which this machine is used
To understand this instruction manual and product warning labels much better, the warning indication is
classified properly as follows. Understand these contents and observe the respective instructions.
This warning is used in the safety precautions and warning labels at the
sections in the potential hazard state that may cause death or serious injury
if not avoided.
These safety precautions involve the preventive action that must be taken
to avoid possible danger.
WARNING
CAUTION
This caution is used in the safety precautions and warning labels at the
sections indicating the potential hazard state that may inflict slight injury or
medium trouble if not avoided.
These safety precautions involve the preventive action that must be taken
to avoid possible danger.
These warning labels must be attached or provided so that they are always seen clearly.
Iftheselabelsarepeeledorfouled,replacethemwithnewones.Whenreplacing,contact
ourcompanyorourlocalagent.
● Classification of Warning Indication
6
A
Warning Label
The hazardous places in this product are
indicated, using 6 types of warning
indicator label.
Thoroughly understand these hazardous
places and indicated contents, and use
this product correctly, observing the
respective instructions.
BC
Since you may
receive electric
shocks, absolutely
avoid touching any
live part.
Since your hand may
be caught in the
movable part during
operation, never hold
out your hands.
Since your hand may
be caught in the
clamp retainer, never
hold out your hands
to the vertical moving
part of clamp retainer
during operation.
CAUTION
Risk of electric shock
DO NOT TOUCH !
CAUTION
Risk of hands getting
caught !
Keep hands away from
movable parts
WARNING
Risk of fingers getting caught
Keep hands away from lifting
parts while operating
B
E
B
B
C
7
D E
F
Warning Label
Introduction
Since there is a
danger of burns due to
a high temperature,
absolutely avoid
touching.
Since there may
arise fault current
and computer
malfunctions,be sure
to set up a grounding
conductor.
Since the knife is
movable, never hold
out your hand to the
movable part during
operation.
CAUTION
Do not touch
Keep hands away from drive
parts whille operating
CAUTION
Make sure of ground
connection
WARNING
Risk of severe burn.
Keep hands away.
B
A
D B
A
B
B
B
F B B
C
B
8
Main Body Front Panel
Parts Identification and Functions
1
2
3
4
5
11
12
13
14
6
8
9
15
Operation panel 1
Safety beam guard
Knife
Knife carrier
Backgauge
Central lubrication pump
Operation panel 2
Knife height adjusting window
Front plate
Table
Knife change lever
Cutting buttons panel
Clamp pedal
Hydraulic oil level gauge
If the optical axis using LED (light-emitting diode)
is interrupted, the knife comes to an instant halt.
Sets the knife
Allows precise paper positioning.
Adjusts the knife height.
This front plate is used when the paper is arranged
properly.
Since this chrome plated table
is provided with an air blowoff nozzle, paper is easy
tohandle.
Works once before start.
The clamp lowers by working the pedal.
12 15
6
7
8
9
1
2
3
4
5
14
11
10
13
7Card rack
10
Used to change the lever.
9
Rear View of Main Body
1
2
3
4
5
6
7
8
Electric box 1
Clamp presser
Presses paper when cutting it.
Gear box
Power box
Electric box 2
Side guide
Used to arrange paper.
Blower motor
Central lubrication pump
Parts Identification and Functions
8
5
2
1
6
3
10
4
7911
Operated once before starting.
9Backgauge
Positions paper accurately.
10
Oil tank
11
Main motor
10
Display panel
Power lamp
Displays the backgauge size, course, page and data
value.
ERA Erases the data.
INS Adds the data.
DEL Deletes the data.
COPY Copies the data to another page.
SCH Accesses the empty course and
corrects the error.
Calculates the data, and can also store the results
thus calculated in memory.
DS Stores the data in memory.
MN Allows all manual operations.
SA Allows automatic positioning.
FA Allows automatic operation.
FAA
Confirmation key for selecting
the full-automatic operation mode.
Changes the units of millimeter and inch.
Selects the backgauge speed.
Changes the fluorescent lamp and cut line.
Corrects the error between the exactsize and indi-
cated size.
Data correction key
3
Calculation key
SPEED
UNIT
Mode key
FL
BM
Operation Panel
1
2
49
8
7
6
5
49
49
34
36
37 50
31 33
29
30
123
0.
456
789
÷
+
-
2
14
3
910 11 12 13 14
×＝
ERA DEL
COPY
SCHINS
CL
STOR
NH
BM
PAGE
PAGE
+
-
CORS
COURSE PAGE
BACKGAUGE
DATA
Otros manuales para Robocut RC-100DX
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cortador de papel de Itotec
