ISGM LP-700 Manual de usuario
LP-700
LED PIXEL
2
LP-700 LED PIXEL
USER MANUAL REV. 1
© 2012 SGMTM. Information subject to change without notice. SGM and all afliated
companies disclaim liability for any injury, damage, direct or indirect loss, consequential
or economic loss or any other loss occasioned by the use of, inability to use or reliance
on the information contained in this manual. The SGM logo, the SGM name and all other
trademarks in this document pertaining to services or products by SGM or its afliates and
subsidiaries are trademarks owned or licensed by SGM or its afliates or subsidiaries.
This edition applies to rmware version 1 or later.
English edition
3
Contents
Dimensions.............................................................................................................. 4
Safety information.................................................................................................... 5
Overview.................................................................................................................. 6
Installing an LP-700 LED Pixel strip ...................................................................... 10
DMX control .......................................................................................................... 12
Service................................................................................................................... 13
Specications ........................................................................................................ 14
4
Dimensions
Measurements in millimeters
and inches (in brackets).
Drawings not to scale.
5
Safety information
The LP-700 LED Pixel system is intended for professional use only. It is not suitable for household use.
Review the following safety precautions carefully before installing or operating the device.
• Do not open the device; there are no user-serviceable parts inside.
• Ensure that power is cut off when connecting the device and its power supply unit to the AC mains supply.
• Ensure that the power supply units are electrically connected to earth (ground).
• Do not apply power if the device or mains cable is in any way damaged.
• Do not immerse the xtures in water or liquid.
• Install only in accordance with applicable building codes.
• Do not paint, cover, or modify the device, and do not lter or mask the light.
• Installation must be performed by a qualied electrician.
• Use only IP65-rated connectors for outdoor installations.
WARNING! Read the safety precautions in this section before
installing, powering or operating this product.
6
Overview
The LP-700 LED Pixel system is a rail-mounted, DMX-controllable, pixel-effect light strip incorporating pixels
with red, green & blue (RGB) color mixing. These strips are IP65-rated and are designed for permanent indoor
or outdoor installation. LED Pixels are ideal for pixel arrays or similar daisy-chained arrays of multiple DMX
controllable effect xtures. LP-700 LED Pixels have an LED life expectancy of 50,000 hours.
Each strip contains 56 LP-700 LED Pixels, but can be cut or spliced to the appropriate length. When installed
on the supplied rails, a pixel array can be installed with a pitch of 60, 80, 100 or 120 mm (2.4, 3.1, 3.9 or 4.7 in.).
(Pitch is the distance from the center of one pixel to the center of the next pixel.) LP-700 LED Pixels are DMX-
controllable and self-addressing, with up to 168 individual pixels being able to be controlled using a single DMX
universe.
Preparing for installation
Each LP-700 LED Pixel strip—or any length of up to 56 pixels—must be connected to an LP-700 power supply
unit (P/N 83061701). The rst strip, or up to 56 pixels, is connected to mains supply and a DMX-compatible control
device (not supplied) using an LP-700 Injector (P/N 83062007). After 56 pixels, the power supply must be boosted
by connecting an additional power supply unit (P/N 83061701) that is connected to mains supply, using an LP-700
Power Injector (P/N 83062008); DMX control is passed from one strip to the next, via the Power Injector.
The maximum cabled-distance between a power supply unit and the rst LP-700 LED Pixel that it supplies power
to is 3 metres (10 feet).
7
8
The maximum number of LP-700 pixels in a controllable daisy chain is 168 (on a single DMX universe). Additional LED
Pixels can be controlled in an installation using multiple DMX universes and separate daisy chains, each chain with its
own Power Injector and up to 168 pixels. Each pixel uses three DMX control channels, and the maximum number of
channels in a DMX universe is 512 (3 x 168=504 channels). Use only IP65-rated connectors for outdoor installations.
Power supply unit
The LP-700 power supply unit (transformer) can operate on any 100–240 V, 50/60
Hz AC mains power supply and supplies 18 V DC to LP-700 LED Pixels via an
Injector (for the rst power supply in a daisy chain of LED Pixels - P/N 83062007)
or power injector (for subsequent booster power supplies in a daisy chain of LED
Pixels - P/N 83062008). Splicing or connecting a power supply unit to mains supply,
or to an injector or power injector, must carried out by a qualied electrician.
Power supply units must be grounded/earthed and be able to be isolated from
AC power. The AC power supply must incorporate a fuse or circuit breaker for fault
protection.
Do not open a power supply unit to replace the supplied power cable, or connect the
device to an electrical dimmer system, as this can damage it.
Injector (power & DMX)
Power Injector
(power & DMX-through)
9
Boosting power using an additional power supply unit and a power injector
Always ensure that power is boosted after every 56 pixels in a daisy-
chain. An LP-700 Power Injector (P/N 83062008) can be used to
supply boost power from an additional power supply unit (PSU - P/N
83061701) and connect two LP-700 LED Pixel strips without splicing
or crimping; the DMX control signal continues unbroken to each xture
in a daisy chain. A 3-metre (10 ft) maximum cabled-distance between
the power supply and the rst LED PIxel it supplies power to applies.
Cutting or splicing strips
Strips can be cut to the required length, but if the system
is installed outdoors, ensure that any exposed cable ends
are sealed using a hot glue gun, or similar IP65-rated
cable sealing method. Splicing strips of LP-700 LED Pixels
together must be carried out by a qualied electrician. The arrow
on the back of each LP-700 LED Pixel indicates the direction
away from the power supply unit.
When and patching, splicing or crimping power and control
cables it is important to note that the LP-700 LED Pixel uses
unbalanced DMX. DMX control only uses pins 1 and 3 of the XLR
connectors. The pinout of the male connectors on the LP-700
LED Pixel strips are shown here in the illustration.
10
Installing an LP-700 LED Pixel strip
The LP-700 system can be installed in any orientation.
1. Afx each rail to a at surface using 4 mm (0.2 in.) countersunk screws.
The distance between the center of parallel rails is the pitch distance.
The distance between pixels (pitch) on a single strip is also
determined by the width (L) of cover that is inserted between each
pixel on the strip. Covers are available in four lengths:
Width (L) Pitch
20 mm (0.8 in.) 60 mm (2.4 in.)
40 mm (1.6 in.) 80 mm (3.1 in.)
60 mm (2.4 in.) 100 mm (3.9 in.)
80 mm (3.1 in.) 120 mm (4.7 in.)
click
PITCH
L
Tabla de contenidos
Otros manuales de Equipo de iluminación de ISGM
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
