IRIS ID IrisAccess iCAM7100 Series Instrucciones de instalación
iCAM7100 SERIES
HARDWARE GUIDE
ADVANCED MULTIFACTOR BIOMETRIC IRIS READER
Fully automatic dual iris capture
Simple non-intrusive, non-contact user interface
Integrated megapixel face camera with flash
ISO/ANSI compliant iris and face images
4.3” color touch screen LCD
Integrated contactless smart card reader [optional]
Surface mount plate included; Recess mounting kit [optional]
VERSION 1.3
Packing List
Required Equipment (not included)
Power Source
12-24 VDC +/- 10% / Minimum 24W (12VDC @ 2AMPS)
(Measured at iCAM unit)
Uninterruptable Power Supply (strongly recommended)
Network
Ethernet Wiring CAT5e Ethernet Cabling (or better)
Ethernet Switch
Software
Required Software for desired system type
(IrisAccess EAC, iData SDK, etc.)
What’s in the Box
iCAM7100 series
Hardware Guide
L wrench
iCAM7100 series Hardware Guide
ISO/ANSI
COMPLIANT
CONTACTLESS
CARD READER
FACE
CAMERA
DUAL
IRIS 4.3 LCD
EASY
INSTALLATION
L wrench
iCAM7101
iCAM7111
iCAM7100 SERIES
HARDWARE GUIDE
ADVANCEDMULTIFACTOR BIOMETRIC IRIS READER
Fully automatic dual iris capture
Simple non-intrusive,non-contact user interface
Integratedmegapixel face camera with flash
ISO/ANSI compliant iris and face images
4.3”Color LCD touch screen available with iCAM7100 models
Integratedcontactless smart card reader [optional]
Surface mount plate included;Recess mounting kit [optional]
VERSION 1.2
Packing List
Required Equipment (not included)
PowerSource
12-24VDC +/- 10% / Minimum 24W (12VDC @ 2AMPS)
(Measuredat iCAM unit)
UninterruptablePower Supply (strongly recommended)
Network
EthernetWiring CAT5eEthernet Cabling (or better)
EthernetSwitch
Software
RequiredSoftware for desired system type
(IrisAccessEAC, iData SDK, etc.)
What’sin the Box
iCAM7100series
HardwareGuide
Lwrench
iCAM7100series HardwareGuide
ISO/ANSI
COMPLIANT
CONTACTLESS
CARDREADER
FACE
CAMERA
DUAL
IRIS 4.3 LCD
EASY
INSTALLATION
iCAM7000SERIES
HARDWAREGUIDE
ADVANCEDIRISRECOGNITION&FACECAPTURESYSTEM
Fullyautomaticfastdualiriscapture
Easynon-intrusiveuserinterface
Widegraphicaluserinterfacewith4.3”LCD[optional]
Intergratedhighresolutionfacecapturecamera
ISO/ANSIcompliantfaceimages
Integratedcontactlesssmartcardreader[optional]
Seamlessintegrationwithconventionalsecuritysystems
EasyinstallationwithGangbox,Cradles,Recessmountingkit
VERSION1.0
ISO/ANSI
COMPLIANT
CONTACTLESS
CARDREADER
FACE
CAMERA
DUAL
IRIS
EYE
SAFETY
EASY
INSTALLATION TUV CE
PackingList
iCAM7000series HardwareGuideLwrench
iCAM7000SERIES
HARDWAREGUIDE
ADVANCEDIRISRECOGNITION&FACECAPTURESYSTEM
Fullyautomaticfastdualiriscapture
Easynon-intrusiveuserinterface
Widegraphicaluserinterfacewith4.3”LCD[optional]
Intergratedhighresolutionfacecapturecamera
ISO/ANSIcompliantfaceimages
Integratedcontactlesssmartcardreader[optional]
Seamlessintegrationwithconventionalsecuritysystems
EasyinstallationwithGangbox,Cradles,Recessmountingkit
VERSION1.0
ISO/ANSI
COMPLIANT
CONTACTLESS
CARDREADER
FACE
CAMERA
DUAL
IRIS
4.3
LCDEYE
SAFETY
EASY
INSTALLATION
TUVCE
RequiredEquipment(notincluded)
PowerSource
12-24VDC+/-10% / Minimum 24W (12VDC @ 2AMPS)
(MeasuredatiCAMunit)
UninterruptablePowerSupply(strongly recommended)
Network
EthernetWiring CAT5eEthernetCabling(orbetter)
EthernetSwitch
Software
RequiredSoftwarefordesired system type
(IrisAccessEAC,iData SDK, etc.)
What’sintheBox
iCAM7000series
HardwareGuide
Lwrench
Lwrench
iCAM7101
iCAM7111
2
Front View
Bottom View
Rear View
Hardware Information
Mirror
Up / Down Tilt Buttons
Face Camera Flash
Proximity Sensor
4.3” Color Touch Screen LCD
Cable Channel
Knock-out
Function Buttons
USB Connector / Screw CAP
Face Camera
Alignment Guide
Smart Card Reader (optional)
Speaker
Status LED
Tripod Socket
(1/4-20 (1/4 diameter, 20 threads per inch))
Surface Mounting
Screw Hole
Gang Box Screw Hole
CCTV Camera (optional)
MIC / Screw Cap
Function Buttons
Tamper Switch
Desktop Stand Hole
Installation Plate
Camera Unit
Interface Panel
3
Hardware Information
OFF ON
Inside
Wiring Legend Guide Rear View
Installation Plate Screw
RTC Battery
Fuse Power LED
Factory Default Button
Power Connection
On/Off Switch
Ethernet Connection
Extra Fuse
Input / Output
Connections
Tamper
Switch
Extra Fuse
Wiring Legend
Guide
4
NOTE
NOTE
NOTE
Installation Guidelines
1. Recommended Mounting Information
2. General Wiring Requirements
54.3”
(138cm)
61”
(155cm)
This is based
on the assumption
that users’ average
height is 5‘7”(170cm)
Floor
Bottom of
Mirror
7.01”
(178mm)
8.31”
(211mm)
2.52”
(64mm)
Ethernet network wiring to connect with the network switch for communication.
Power Wiring: The minimum recommended wire gauge used for power is 16AWG (1.0mm )
Power Requirements: 12-24VDC +/- 10% / Minimum 24W (12VDC @ 2AMPS)
The iCAM7100 series requires at least the following wires:
2
IMPORTANT: IT IS RECOMMENDED THAT THE IRISACCESS SYSTEM BE PLACED ON A PRIVATE NETWORK
SEPARATE FROM GENERAL CORPORATE OR PUBLIC ACCESS. SYSTEM PERFORMANCE AND STABILITY MAY BE
AFFECTED DEPENDING ON AMOUNT OF GENERAL NETWORK TRAFFIC.
IMPORTANT: IT IS RECOMMENDED TO SUPPLY THE CORRECT AMOUNT OF POWER TO THIS UNIT. AN OVER OR
UNDER VOLTAGE APPLIED TO THIS PRODUCT MAY CAUSE PERMANENT DAMAGE AND VOID THE WARRANTY.
2
The iCAM was designed for indoor use only. This device is not weatherproof and must not be
exposed to precipitation or extreme temperatures. If it is required to use this product in an
outdoor or extreme environment, a 3rd Party enclosure may be used to protect the unit from
exposure to dust, moisture, and extreme temperatures. See www.irisid.com - Support &
Service for more information. Installation in a extreme environment without proper protection
may cause permanent damage and void your warranty.
The recommended mounting height for the iCAM7100 series is 138cm (54.3inches) from the
floor to the bottom of the unit. This mounting height can be adjusted to accommodate the
height of the average user at the installed location.
High amounts of ambient light must be avoided. Intense light sources such as sunlight or
halogen lamps may reduce the image capture performance of the iCAM which may result in
an increased “failure to acquire” rate.
Use of a stable power supply and proper guage wire is required. Wire length voltage
drop must be accounted for in order to maintain the correct power at the iCAM unit (with
iCAM connected). For example; with a 12VDC source and 16AWG (1.0mm ) copper wire, the
maximum distance is 71.5 Feet (21 Meters). If a longer power wire distance is required, it is
recommended that a 24VDC power source be used. Voltages within the range of 12VDC and
24VDC are acceptable as long as 24W of power is supplied to each iCAM.
(e.g. 12VDC @ 2AMPS = 24Watts OR 24VDC @ 1AMP = 24Watts).
For systems consisting of only the iCAM and a computer, an Ethernet cross-over cable
may be used.
5
1Open each cap at both sides of unit,
and loosen the captive screws (with included L wrench)
to release the interface panel.
(Left : MIC / Screw Cap.
Right : USB Connector / Screw Cap)
2
iCAM7100 Mounting & Stand Solutions
iCAM Installation
The iCAM7100 series unit can be fitted to a surface mount (available out-of-the-box), recess mount
(with optional recess mounting kit), or optional desktop stand.
Surface Mounting
After opening the interface panel, loosen the screw.
Unscrew the installation plate screw to seperate from the installation plate.
Seperate the installation plate
by sliding the plate downward.
3
Cover Rear
Installation Plate
The iCAM can be surface mounted with standard equipment provided with the contents of your unit.
Review the following procedure for instruction on how to surface mount your iCAM7100 series unit.
6
Slide the iCAM7100 series
into the installation plate
and fasten the installation
plate with a screw.
OR
5
Place the installation plate on the desired wall and screw into wall.
Feed any needed wiring through the installation plate hole (i.e.: Power, Ethernet, etc).
Attach the installation plate to the wall surface using the appropriate fastener (recommended
#10 screws) and anchors for the wall material. Another option is to mount and fasten the
installation plate to a previously installed electrical gang box.
4
Installation Plate
Surface Mount
Gang Box Mount
Hole Marking
Installation Plate
OFF ON
Turn on power source and switch the power switch of the iCAM7100 series
unit to the ON position.
8
After wiring the unit and switching
it to the ON position, close the interface panel
and fasten the screws.
(with screw caps placed back into closed position).
9
Remove protective film from RTC battery.
6
Before wiring unit, confirm the power
is in the off position. Route and connect
the Power and Ethernet wires to
iCAM7100 series.
7
NOTE
OFF ON
Remove the coin
battery protect film
OFF ONOFF ON
Power on
Power Supply
Connector
Ethernet
Cable
OFF ON
If connecting any other wiring such as Wiegand, GPI/O to the iCAM, review the following
section “Wire Connection Details” before closing interface panel and fastening screws.
7
Relay Output
A
A B C
D FE
G
Wire Connection Details
Relay Output
Two independent dry contact relays. The purpose and the duration of the relays are defined
by the controlling software. Typically, Relay_1 (NC_1, COM_1, NO_1) is triggered upon user
acceptance (access granted). The diagram shows Relay_1 connected to indicators which
changes from Red to Green for an accepted user. Relay_2 (NC_2, COM_2, NO_2) is typically
used to indicate iCAM tamper. In this diagram the relay is activated when the iCAM tamper
switch is triggered. The maximum electrical rating for the relay is 3A at 24VDC.
IMPORTANT: ONLY KNOWLEDGEABLE PROFESSIONAL INSTALLERS SHOULD BE USED TO INSTALL ALL
ELECTRONIC ENTRY/EXIT LOCKING DEVICES. DIRECT CONNECTION OF ELECTRONIC ENTRY/EXIT LOCKING
DEVICES SHOULDN’T BE MADE FROM THE RELAY OUTPUTS ON THE ICAM. IT IS THE RESPONSIBILITY OF THE
INSTALLER TO ASSURE THAT THE INSTALLATION IS PERFORMED IN ACCORDANCE WITH ALL COUNTRY/STATE/
LOCAL FIRE AND SAFETY REGULATIONS AND THAT ANY 3RD PARTY PRODUCTS USED WILL NOT CREATE A
HAZARD.
NC_1
RED
LIGHT
POWER
SUPPLY
COM_1
NO_1
NC_2
COM_2
NO_2
ALARM
SYSTEM
24 HOUR
ZONE
GREEN
8
GPIO Specifications:
o'PSPVUQVUUIF(1*0DBOQSPWJEF7%$!N"
o'PS*OQVUUIF(1*0JTTFMFDUBCMFCFUXFFOBDUJWF)JHIBDUJWF-PX
o"TTJHONFOUPG(1*0JTIBOEMFEUISPVHI4PGUXBSF
Wiegand Output
8JFHBOE4QFDJGJDBUJPOT
o8JFHBOEPVUQVUVTFTXJSFJOUFSGBDF%BUB%BUBBOE(SPVOE
o.BYJNVNXJSFMFOHUIGSPNJ$".UP"DDFTT$POUSPM1BOFMJTGFFUN
C
External GPIO
(1*0BOEDBOCFVTFEUPDPOUSPMUIFUJMUQPTJUJPOPGUIFUJMUVOJUPGBOJ$".
6TF(1*0BOE(/%GPSVQUJMUJOH6TF(1*0BOE(/%GPSEPXOUJMUJOH
D
External GPIO
External Tilt
ACCESS
CONTROL
PANEL
GPIO1
GND
GPIO2
GND
GPIO3
GND
GPIO4
GND
GROUND
DATA_1
DATA_0
GPIO3
GROUND
GPIO4
GROUND
Wiegand Output
NC
DATA_0
DATA_1
GND
Card Reader
Interface
Up
Down
5IF8JFHBOE0VUQVUGSPNUIFJ$".TFSJFTDBNFSBVOJUDBOCFVTFEXJUISEQBSUZ
EFWJDFTDBQBCMFPGSFDFJWJOH8JFHBOEEBUB5IJT8JFHBOEPVUQVUFNVMBUFTBUZQJDBM"DDFTT
$POUSPM$BSE3FBEFS$POGJHVSBUJPOPGUIJTPVUQVUJTQSPWJEFEUISPVHITPGUXBSF
4FFUIFBTTPDJBUFEJNBHFGPSHFOFSBMXJSJOHPG8JFHBOE0VUQVUUPBO"DDFTT$POUSPM1BOFM
9
Wiegand Input
B
Wiegand Intput
12VDC
12VDC
DATA_0
DATA_1
GROUND
DATA_0
DATA_1
GND
External
Prox Card
Reader
8JFHBOEJOQVUJTBWBJMBCMFPOUIFJ$".GPSDPOOFDUJPOGSPNSEQBSUZQSPYJNJUZDBSESFBEFST
5IJTDPOOFDUJPODBOQSPWJEF7%$BOEBNBYJNVNN"DVSSFOUUPBQSPYJNJUZDBSESFBEFS
10
External Smart Card Interface RS232 Smart Card
F
External Smart Card Interface
RS232 Smart Card
12VDC
TXD
RXD
GND
External
Smart Card
Reader
Allows connection of internally (ex. HID OEM150) and externally installed smart card readers
which utilize serial (RS232) communications. This connection can provide 12VDC and a
maximum of 500mA current to a smart card reader.
RS422 Output
E
RS422
Output
To RS422 port
of computer
or access system
RXD_P
RXD_N
TXD_P
TXD_N
RXD_P
RXD_N
TXD_P
TXD_N
RS422 serial communication port for connection with an access panel or to other computer
equipment. When configured, the Card ID associated with the user is output from the
RS422 output port upon a successful identification.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Controladores de acceso IP de IRIS ID
