IPC Eagle SC4 Manual de usuario

OPERATIONS MANUAL

& PARTS LIST

SC4

Fastracts Extractor

IPC Eagle •3650 Dodd Rd, Eagan MN 55123 •800.486.2775 •www.ipceagle.com

WHEN THE MACHINE IS DELIVERED

Check the carton carefully for signs of rough handling. Remove the machine from the carton. If

the machine is damaged, notify the carrier immediately and request an inspection. Be sure to keep the

carton, packing inserts, packing lists and carrier’s receipt until the inspector has verified your claim.

Eagle Power’s liability ceases when the shipment is picked up by the carrier but our customer

service staff will be glad to furnish any information needed in connection with the claim and will

expedite repair of the machine.

Obtain a return authorization number from the factory before returning the machine to us for repair

or service.

BEFORE OPERATING THE MACHINE

Read the manual carefully and completely before attempting to operate the unit. This manual has

important information for the use and safe operation of the machine. Keep this manual handy at all

times. This machine will ensure years of satisfactory service if operated and maintained according to

recommendations in the manual. If additional information is needed, please contact your local

distributor or write to:

IPC Eagle

3650 Dodd Rd

Eagan, MN 55123

800-486-2775

All information and specifications printed in the manual and parts list are current at the time of printing;

however, because of Eagle Power’s policy of continual product improvement, we reserve the right to

make changes at any time without notice.

This machine is shipped with antifreeze in the solution line system to protect the pump and valves

from freezing during transport and storage. Before you use the unit, rinse the solution line system

with clean water (See Preparing The Machine).

WARRANTY

To protect your investment, promptly fill in the required information on the warranty card that

comes with the unit and mail it back to Eagle Power.

WARNING

To reduce the risk of fire, electric shock, or injury:

•Do not leave the machine when plugged in. Unplug from the outlet when not in use and before

servicing.

•Use indoors only.

•Do not allow to be used as a toy. Close attention is necessary when used by or near children.

WARNING

•The machine was designed for use on carpet, hard floors and upholstery extraction

application as per instructions and recommendations written in this manual. Any deviation

from its proper use or purpose and the consequential damage that may occur is the sole

responsibility of the end user.

•Do not use with damaged cord or plug. If machine is not working as it should, or has been

dropped, damaged, left outdoors, or dropped into water, return it to an authorized service

center.

•Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord

around sharp edges or corners. Do not run machine over cord. Keep cord away from

heated surfaces.

•Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

•Do not handle plug or appliance with wet hands.

•Make sure the machine is plugged into an electrical outlet with the same voltage and

frequency rating as shown on the nameplate of the machine. Do not attempt to plug a 115

volt machine into a 230 volt outlet.

•Do not immerse or use this machine in standing water. Such use can cause electric shock.

•Do not use to pick up flammable or combustible liquids such as gasoline or use in areas

where they may be present.

•Do not expose machine to freezing temperatures.

•To avoid electric shock, do not expose the unit to rain - store it indoors only.

•Connect to a properly grounded outlet only. See “Grounding Instructions.

•Turn off all controls before unplugging.

•Do not use without filters in place.

•Do not put any object into openings. Do not use with any opening blocked; keep free of

dust, lint, hair and anything that may reduce air flow.

•Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot

ashes.

•Do not use machine for dry vacuuming. This machine is not outfitted with a fine dust filter

and it will damage the vacuum motor(s).

•Do not turn on the vacuum-pump switch when the solution tank is empty.

•Use defoamer at all times to prevent damage to the vacuum motor.

•Do not use water in excess of 140 F (62 C).

WARNING

•Use only commercially available carpet cleaners and defoamer intended for use with extraction

machines of this type. Do not use dyes, bleaches, ammonia, or other additives. The use of

powdered cleaning solution if not diluted properly may result in damage to the pump.

•All servicing of Eagle Power equipment should be performed only by Eagle Power authorized

service centers.

•Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts.

•Use extra care when cleaning on stairs.

•Do not use replacement parts other than those specified in the parts list. Proper maintenance of

the machine could be affected if substitutions are made.

•Follow maintenance schedule strictly.

•FAILURE TO COMPLY WITH THE WARNING INSTRUCTIONS WILL VOID THE WARRANTY.

GROUNDING INSTRUCTIONS

To protect the operator from electric shock, Eagle Power equipped the machine with

an approved three conductor cord and grounding plug. This plug is to be used only

with the proper grounding type receptacle.

The machine has a plug like the one shown in figure (A). An adapter is available for

connecting three prong type plugs to two prong receptacles (see figure B). The green

colored rigid lug extending from the adapter must be connected to a permanent

ground such as a properly grounded outlet box. Do not break off or pull out the

grounding prong on the plug because it protects the operator from electric shock.

CLEANING TIPS

•Check the condition of the area to be cleaned. Look for loose carpet, heavily soiled area, stains

or spots and worn areas. Bring these to the attention of the person in charge before performing

the cleaning job. Make sure all edges of the carpet are securely tacked in place and all seams

are sewn (or glued) tight. This is your protection against shrinkage.

•Locate an inconspicuous spot on the area to be cleaned. Test carpet for colorfastness before

proceeding. Pour the concentrated cleaning solution on the spot, cover with a white towel and

place a heavy object on top to absorb the cleaning solution. Wait approximately 10 minutes for

any reaction to take place. Remove weight. If there is no color transfer, it should be safe to

clean. Apply this procedure if different color-texture carpet is seen in adjacent rooms or areas to

be cleaned.

•Remove the furniture from the area to be cleaned. Large pieces can be moved to opposite end

of the room from where you start cleaning and replaced when it is completed. After cleaning

carpet, place a small square of aluminum foil under the furniture legs to prevent moisture from

•Clean the area with an upright vacuum. DO NOT USE THIS MACHINE AS A DRY VACUUM! Heavily

soiled carpet or areas of concentrated foot traffic should be treated with recommended prespotting or

pre-spray chemicals. If a spotter is used, follow label directions exactly. Do not allow any spotter or pre-

spray to dry on the carpet as it may damage the carpet permanently.

•Identify the type of carpet fiber to be cleaned. Most commercial carpet fibers in use are acrylic or nylon

based. Best results in cleaning would be obtained if hot water is used to clean these type of fibers. On

the other hand, hot water would shrink natural fiber carpeting, like wool and cotton in particular.

Exercise caution when cleaning natural fibers by using cool water, testing for colorfastness and

applying the least amount of cleaning solution possible.

•Plan your cleaning route. Start cleaning at the farthest point away from where you plugged the machine

and work back towards the outlet so that the cord will not get in the way.

TO CLEAN CARPET

1. Prepare the Machine

Make sure “switch” is in the “off” position and all hoses are

connected. Using only approved cleaning solution, mix according

to the bottle instructions using the “bucket.” To reduce foaming pour

2 ounces of defoamer into the recovery bladder. Place bucket onto

machine and close lid.

2. To Clean

Turn switch to carpet position. Turn pump switch “on.” While pushing

“activate” switch pull machine as you step backwards. Release the

“Activate” switch 6 inches before ending a stroke. Repeat cleaning stroke

with 3" overlaps. Continue cleaning until cleaning solution is consumed.

Empty and rinse bucket, repeat steps 1 and 2.

3. Check Bucket Lid

If excessive foam appears in lid ad 2 ounces of defoamer or empty and

rinse bucket, repeat steps 1 and 2.

4. Clean Machine Before Returning

Clean “Lid Filter Screens” and rinse out bucket. Wipe all surfaces including

bottom of machine. Remove carpet lint and strings from brush and vacuum nozzle.

TO CLEAN UPHOLSTERY

Cleaning upholstery with success requires a good knowledge of the type of fabric to be worked on. Look

for cleaning instruction label sewn on the underside of the furniture for the recommended method of

cleaning the fabric. If it calls for dry cleaning, do not attempt to clean with the wet extraction method.

Otherwise, damage to the fabric could occur. Extraction works on most synthetic fabrics.

Before proceeding, test fabric for colorfastness. Pour a small amount of cleaning solution on the fabric

in an inconspicuous spot.

Rub the area with a white terry towel. If no color comes off the towel, the fabric should be safe to clean. If

color transfers, do not continue.

1. Prepare the Machine

Complete step 1 under Carpet Cleaning Instructions using approved Upholstery Cleaning Solution.

Disconnect vacuum hose with black hose cuff from lid and disconnect solution hose from back of

machine. Replace them with the upholstery hoses.

2. To Clean

Turn switch to upholstery position. If the machine is an all floor model turn the “solution control valve” located

on the side of the machine to “carpet.” Turn pump switch “on.” Depress upholstery tool trigger while pulling tool

across upholstery surface with overlapping strokes. To speed drying go over the upholstery without depressing

trigger. Continue cleaning until cleaning solution is consumed. Empty and rinse bucket, repeat Step 1 and 2.

3. Check Bucket Lid

See Step 3 under “To Clean Carpet.”

4. Clean Machine Before Returning See step 4 under To Clean Carpet.

DAILY MAINTENANCE

The Fastracts SC4TM is engineered and built to require minimum maintenance. But like any machine, it does

require some care to keep it in optimum working condition. Careful attention to these maintenance instructions

will give you maximum operating performance and life expectancy of the machine.

CAUTION: Disconnect power cord from the outlet before doing any clean up or maintenance on

the machine.

1. Keep the machine clean, inside and out including the lid, bucket, brush and brush chamber.

2. Pour a gallon of clean hot water in the smaller opening of the bucket. Turn the pump on and

flush the entire system through the spray nozzles for about a minute to prevent alkaline build-up.

3. Keep filters clean.

4. Quick connect coupler - spray with silicone lubricant to keep coupler from sticking.

5. Valve, upholstery tool - If the plunger on the valve sticks, spray with silicone lubricant.

TROUBLE SHOOTING

PROBLEM POSSIBLE CAUSE

ELECTRICAL SYSTEM

No electrical power. 1. Defective power cord.

2. House or building circuit breaker tripped.

Switch is turned on. 1. Faulty electrical cable.

Power is intermittent to 2. Defective Switches

all motor(s) 3. Loose terminal or terminal connections.

VACUUM SYSTEM

No Vacuum 1. Vacuum lid is not sealed against tank.

2. Loose vacuum hose, vacuum connection.

Low Vacuum 1. Accumulated dirt on lid screen.

2. Worn out vacuum lid gasket.

3. Lint & dirt build-up on vacuum nozzle.

4. Defective vacuum hose.

5. Loose connection in the vacuum motor(s)

SOLUTION SYSTEM

Pump motor is on, no 1. Small opening side of bucket is empty.

spray through spray tip. 2. Clogged spray tip.

3. Clogged filter screen on end of dome hose.

4. Plugged female quick disconnect coupler.

5. Punctured pump diaphragm.

6. Defective pump check valve.

7. Crack in pump housing.

8. Debris in check valve.

Uneven or weak spray 1. Clogged or dirty spray tip.

from tip. 2. Accumulated dirt on filter screen of dome hose.

3. Accumulation of debris inside pump and plumbing.

4. Worn pump bearing (excessive noise)

5. Punctured pump diaphragm.

6. Defective rectifier or motor.

7. Worn nozzles.

BRUSH SYSTEM

Motor runs, 1. Defective belt.

brush won’t spin 2. Brush jammed.

Brush motor fails 1. Brush jammed.

to turn on after 2. Blown breaker.

circuit breaker has 3. Defective motor.

been reset. 4. Defective switch.

5. Loose wiring connection.

ITEM # PART # QTY FIG.

1 C00311

PARTS LIST

DESCRIPTION

8-32 X 3/8 ROUNDHEAD MACHINE BLACK PHILLIPS SS 21

2 D10483 PLATE, MNTNG, SWITCHES, 115V, GREY 1 1

2A D10713A ASSY, SWITCHPLATE W/SILKSCREEN LABEL (3 SWITCHES) 11

2B D10998A ASSY, SWITCHPLATE W/SILKSCREEN LABEL (1 SWITCH) 1 1

3 B00214-2 COVER, SWITCH, ROCKER 2/3 1

4 B00188 SWITCH, ROCKER, DPDT BLACK 1 1

5 E10698

GASKET, SWITCHPLATE, EVA, ADHESIVE BACKED, 3 GALLON UNIT

6 C10739 SCREW, 6-32 X 5/8, PHIL. PH. BLACK OXIDE 2 1

7 D10481 PLATE, MNTNG, MOMENTARY SWITCH, WHITE EPOXY FINISH 11

7A D10481-1 PLATE, MNTNG, MOMENTARY SWITCH, GREY EPOXY FINISH 11

8 B10513 SWITCH, PUSHBUTTON, 250V DP N/O 12 AMP 1 1

9 D10590-1 PLATE, MOMENTARY, MOMEN, EPOXY GREY 1 1

10 E10705 GASKET, MOMENTARY 1 1

11 H10518-5 LABEL, INSTRUCTION 1 1

12 D10496 PLATE, COVER, MNTG, POWER CORD, BLACK 1 1

13 C00311 8-32 X 3/8 ROUNDHEAD MACHINE BLACK PHILLIPS SS 4 1

14 B02211-1 SWITCH, ROCKER, LIT GREEN, 115 / 230V, 20A 1/2 1

15 B10554 CIRCUIT BREAKER, 1.2 AMP, 250 VAC, RESETTABLE 1 1

16 B02193 CIRCUIT BREAKER SEAL 1 1

17 H10509 LABEL, SWITCH PLATE, (2 SWITCHES) 1 1

Not Shown B10509 HOUR METER 1 1

Tabla de contenidos

Otros manuales de Máquina de piso de IPC Eagle

IPC Eagle

IPC Eagle B1500 Manual de usuario

IPC Eagle

IPC Eagle CT230 BT100 Manual de usuario

IPC Eagle

IPC Eagle 1050 Manual de usuario

IPC Eagle

IPC Eagle CT110 Manual de usuario

IPC Eagle

IPC Eagle SC7 Manual de usuario

IPC Eagle

IPC Eagle Integra-D ORB20 Manual de usuario

IPC Eagle

IPC Eagle BT85 Manual de usuario

IPC Eagle

IPC Eagle PB24 Manual de usuario

IPC Eagle

IPC Eagle Cleantime CT230 Manual de usuario

IPC Eagle

IPC Eagle BB20N Manual de usuario

IPC Eagle

IPC Eagle CT70R Manual de usuario

IPC Eagle

IPC Eagle 512 Rider Manual de usuario

IPC Eagle

IPC Eagle B2000 Manual de usuario

IPC Eagle

IPC Eagle ct70 rider Manual de usuario

IPC Eagle

IPC Eagle CT160 700 Manual de usuario

IPC Eagle

IPC Eagle FLEC02-B Manual de usuario

IPC Eagle

IPC Eagle 1404 Manual de usuario

IPC Eagle

IPC Eagle BX2 Fastracts Extractor Manual de usuario

IPC Eagle

IPC Eagle BX12 Manual de usuario

IPC Eagle

IPC Eagle CT160 Manual de usuario

IPC Eagle

IPC Eagle Propane Powered Floor Care Equipment Guía del usuario

Manuales populares de Máquina de piso de otras marcas

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Manual de usuario

Numatic

Numatic ET 4045 Manual de usuario

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Manual de usuario

Mytee

Mytee 8070 Mytee-Lite Manual de usuario

Kärcher

Kärcher B 140 R Manual de usuario

Triple S

Triple S Ace 26T1 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance SW 750 Manual de usuario

Tornado

Tornado Marathon 2000 98190 Manual

Windsor

Windsor ADMIRAL Admiral 8 Manual de usuario

Numatic

Numatic TTB 1117/100 Manual de usuario

Tennant

Tennant 8210D Manual de usuario

Nobles

Nobles Frontier Manual del producto

lavina

lavina 21-X Manual de usuario

KENT

KENT Edge 28B Manual de usuario

Tennant

Tennant 215 Manual del producto

Windsor

Windsor BDP 51/2000C Manual de usuario

CleanFreak

CleanFreak DURA-18HD Manual de usuario

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Guía del administrador