IOptron IPolar Manual de usuario

Replacing a iPolar with a Optical Polar Scope

Tool needed: a set of metric hex key wrench and a small

Phillips screwdriver

1. Loosen two screws at the front of the mount and

two others on the top of a SkyGuider Pro main

board cover and remove the black cover.

2. Unplug the 6-wire motor driver cable and DC power

cable. Remember how wires wrapped.

3. Remove two mounting screws.

4. Gently pull the circuit board with sockets end up

and slide the circuit board out. If the board is stuck

by the motor, loosen two Phillips screws hold the

motor.

5. Remove polar scope base plate.

6. Rotate the RA axis to find TWO set screws which are

used to secure the iPolar in place. Use a 1.5mm hex

key to release the set screws. Pull the iPolar out of

the RA axle.

7. Insert optical polar scope into the RA axis. Rotate

the front camera mounting adapter to desired

orientation and adjust the polar scope so that the

LED illuminating hole is facing upward.

8. Lock polar scope via these 2 set screws.

Wire wrapping

9. Install the polar scope LED abr. Make sure the cable

plug is placed on the left side as shown.

10. Connect the polar scope LED cable between the LED

bar and the control board.

11. Sliding the front end of the control board in. Make

sure the LED cable underneath is not jammed.

12. Gently push the board in when the power cable

goes through the small cut on the board.

13. If you release the motor to gain more space while

remove the board, tighten motor locking screws

while push the motor against worm assembly to

tension the belt properly.

14. When securing the board with two screws, make

sure that the battery and wires underneath are

properly seated. Fully tighten the screws.

15. Plug in the battery wire and motor cable. Refer to

step 2 to wrap the wire properly. Put the cover and

screws on.

16. Replace the polar scope base plate.

Otros manuales para iPolar

3

Otros manuales de Accesorios de iOptron

iOptron

iOptron SmartStar CubePro Manual de usuario

iOptron

iOptron SmartEQ Pro Plus Manual de usuario

iOptron

iOptron CEM60 Manual de usuario

iOptron

iOptron ZEQ25GT Manual de usuario

iOptron

iOptron iEQ45 Pro Manual de usuario

iOptron

iOptron SmartStar Cube Manual de usuario

iOptron

iOptron CEM60EC Manual de usuario

iOptron

iOptron CEM26 Manual de usuario

iOptron

iOptron AccuAligning Manual de usuario

iOptron

iOptron CEM70 Manual de usuario

iOptron

iOptron ZEQ25 Manual de usuario

iOptron

iOptron SmartStar iEQ45 Manual de usuario

iOptron

iOptron SkyGuider Manual de usuario

iOptron

iOptron HAE69 Manual de usuario

iOptron

iOptron CEM70 Manual de usuario

iOptron

iOptron SmartStarMiniTower II Manual de usuario

iOptron

iOptron MiniTower-II Manual de usuario

iOptron

iOptron HEM15 Manual de usuario

iOptron

iOptron HAE29 Manual de usuario

iOptron

iOptron iPolar Manual de usuario

iOptron

iOptron SmartEQ Manual de usuario

iOptron

iOptron PoleMaster 3338-25? PoleMaster 3338-34? PoleMaster... Manual de usuario

iOptron

iOptron SmartStar 8600A Manual de usuario

iOptron

iOptron iPolar 3339R-SGP Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario