ION PROJECT ROCKER Manual de usuario

Quickstart Guide English ( 3 – 8 )

Guía de inicio rápido Español ( 9 – 14 )

Appendix English ( 15 )

Quickstart Guide (English)

Introduction

Thank you for purchasing the Project Rocker. At ION, your entertainment is as important to us

as it is to you. That’s why we design our products with one thing in mind—to make your life

more fun and more convenient.

Note: Before you first use the product, please fully charge the battery. Your unit was

purposely shipped with a reduced battery charge to ensure safe transit.

Use the included power cable to connect the unit to a power outlet and let it charge for up to 5

hours. This helps ensure the longest life for your battery.

Box Contents

Project Rocker

1/8” (3.5 mm) Stereo Aux Cable

Power/Charging Cable

Quickstart Guide

Safety & Warranty Manual

Support

For the latest information about this product (documentation, technical specifications, system

requirements, compatibility information, etc.) and product registration, visit ionaudio.com.

For additional product support, visit ionaudio.com/support.

Rechargeable Batteries

Rechargeable lead-acid batteries are the same type used in automobiles. As with your car

battery, how you use this battery has a significant impact on its lifespan. With proper use and

treatment, a lead-acid battery can last for years. Here are some recommendations for getting

the longest life from the internal battery.

General Usage Fully charge the battery before using it.

Charge the battery completely after each use.

Storage For best product longevity, do not store at exceedingly hot (greater than

90°F/32°C) or exceedingly cold (less than 32°F/0°C) temperatures.

It is acceptable to leave your sound system plugged in. This will not

overcharge the battery.

If you leave the battery level low and do not charge it for 6 months, it may

permanently lose capacity.

Repair If the battery fails to charge, check your fuse near the power cable input. If your

fuse is intact and it still will not charge, contact ION Audio at ionaudio.com.

Disposal Bring the unit to a recycling center or dispose of in accordance with local

ordinances.

Outdoor Use and Care

Though Project Rocker is water-resistant and able to tolerate splashing water, please review

the tips below to get the best performance from Project Rocker:

•Project Rocker must only be used outdoors with power outlets or extension cords that are

rated for outdoor use.

•Bring Project Rocker indoors during extreme weather.

•Please do not place Project Rocker in standing water.

•Please do not connect the power cable to Project Rocker in a wet environment. Make sure

the power input, power cable, and power outlet are all completely dry before making any

connections.

•WARNING: Keep any non-water-resistant devices (phones, music players, etc.) in a dry

place where they will not be affected by water and cause a risk of electric shock.

Quick Setup

1. Make sure all items listed in the Box Contents are included in the box.

2. Read the Safety & Warranty Manual before using the product.

3. Make sure the battery is completely charged prior to first use for maximum battery life.

4. Ensure the Master Volume on Project Rocker is at zero.

5. Connect your devices.

6. Raise the volume to a comfortable level.

7. Return the Master Volume to zero before powering off when you are finished using

Project Rocker.

Features

Front Panel

10 11

1. Display: Displays the current radio station and device status.

•Charging Indicator: When the power cable is connected, movement of the top

battery segment shows the battery is charging. When fully charged, all battery

segments will be lit without blinking. When the power cable is disconnected, the

battery segment shows the level of the battery.

•Power Icon: The power icon will be lit when Project Rocker is powered on.

•Lightning Bolt Icon: The lightning bolt icon will be lit when the power cable is

connected to wall power.

•Bluetooth Icon: The Bluetooth icon will not be lit when Project Rocker is first

powered on (unless it was previously paired with a device). The Bluetooth icon will be

lit solid when a device is paired to Project Rocker.

•Bass Boost Indicator: The Bass Boost indicator will be lit when the Bass Boost

function is activated.

•AM/FM Status: When listening to AM or FM radio, the corresponding indicator will

appear next to the current station number on the right.

2. Power Button: Turns Project Rocker on or off. Please note that while Project Rocker is

connected to a power source, it does not need to be powered on to charge the battery.

When the power is on, the display will show the power indicator.

3. Bluetooth Button: Press the Bluetooth button to disconnect a paired Bluetooth device.

Press and hold this button for 1 second to disable (or enable) the voice prompts.

4. Light Button: Press this button to turn the LED light on or off.

5. Radio Selector: This button sets the radio to FM, AM, or turns the radio off.

6. Bass Boost: Press this button to enhance the overall bass frequency response.

7. Tune/Track Buttons (</>): Tap these buttons to tune in a radio station or go to the

previous/next track on a Bluetooth connected device. To “seek” (jump to the next available

station), hold either button down for a few seconds until it starts to seek a station. The unit

will remember the last station it was on and start at that station when powered off and on

again.

8. Play/Pause: Press to play or pause a track from a connected Bluetooth device. Press and

hold this button to select a previously saved preset station. See the section Using the

Radio for more details on saving and recalling presets.

9. Master Volume Control: This adjusts the speaker’s main mix volume, which includes the

Auxiliary Input, Radio, and the audio of a paired Bluetooth device.

10. Auxiliary Input: This stereo 1/8” (3.5 mm) input can be used to connect a CD player, MP3

player, or other audio source.

11. USB Charging Port: Connect your device’s charge cable here to charge it. USB charging

only functions when the unit’s power is turned on.

Note: To charge smartphones and tablets faster, put the device’s screen to sleep.

Top Panel

1. NFC: Tap your NFC (near-field communication) supported and enabled device

here to pair your phone by gently bumping on the ‘N’ logo.

2. Mechanical Features: Use this panel to hold drill bits/screws/parts, imperial and metric

rulers, a protractor, and a socket tray.

Rear Panel

1. Power Cable Input: Insert the included power cable here to charge the unit.

Note that the Project Rocker can be used with the power cable while it

simultaneously charges the battery.

Side Panels

1. Storage Pouches: Use these pouches for holding tools.

Operation

Pairing a Bluetooth Device

1. Turn on your Bluetooth device.

2. Power on Project Rocker. If you have previously connected to another Bluetooth device,

Project Rocker will reconnect. To disconnect pairing if the Bluetooth icon is lit solid, press

and release the Bluetooth button.

3. Navigate to your Bluetooth device’s setup screen, find “Project Rocker” and connect.

Note: If your Bluetooth device prompts for a pairing code, enter “0000”.

To disconnect pairing while the Bluetooth icon is lit solid, press and release the Bluetooth

button.

To connect to another Bluetooth device, repeat step 3.

Note: Maximum range will be achieved when using devices with Bluetooth 4.0 or higher.

Pairing a Bluetooth Device Using NFC

NFC (near-field communication) allows data exchange from devices, such as pairing, by gently

bumping them together. Check in your device’s manual to see if this feature is supported.

To use NFC to pair with Project Rocker:

1. In order to use NFC, your device must be turned on and unlocked.

2. Enter your device’s Settings menu and check that NFC is turned On (one-time step).

3. Power on Project Rocker.

4. Touch and briefly hold your device to the NFC logo located on Project Rocker’s top panel.

5. Follow the pairing instructions that appear on your phone. If a passcode is required, enter

“0000”.

6. To unpair, gently bump your device against the NFC logo.

Using the Radio

Selecting a radio station:

1. Press the Radio button.

2. Use the Tune/Track (</>) buttons to search for a radio station. To "seek" (jump to the next

available station), hold a Tune/Track button down for a few seconds until it starts to seek

a station. The unit will remember the last station you were on and start at that station when

you power off and power on again.

Saving a preset:

1. Press the Radio Selector button to choose FM/AM and select a radio station that you

want to save to a preset location using the Tune/Track (</>)buttons.

2. Press and hold Play/Pause for 3 seconds. A preset number will appear on the screen.

3. Use the </> buttons to select which preset you want to save it to.

4. Press Play/Pause to confirm. SAVE will appear on the screen.

Selecting a preset:

1. Press and hold Play/Pause for 3 seconds. A preset number will appear on the screen.

2. Use the </> buttons to cycle through the saved presets. The preset will load after a few

seconds.

Troubleshooting

If the unit is not charging: Make sure the power cable is properly connected to the power

input and the power outlet.

If the sound is distorted: Try lowering the volume control of your sound source. Also, try to

reduce the overall volume of Project Rocker using the Master Volume knob.

If there is too much bass: Try adjusting the tone or EQ control on your sound source to lower

the bass level. This will allow you to play the music louder before clipping (distortion) occurs.

If there is poor AM reception: To adjust AM reception, move entire unit.

If you can’t play music from a flash drive: The USB port is only for charging USB devices.

If you cannot connect your audio device to Project Rocker via Bluetooth:

•Have your audio device (e.g., smartphone or tablet) and Project Rocker as close together

as possible while trying to connect. Make sure both the audio device and Project Rocker

are unobstructed by walls, furniture, etc.

•Reset the Bluetooth connection on Project Rocker to disconnect Project Rocker from any

other audio device and restart the search process. If this does not work right away,

power off Project Rocker and then power it back on. See Pairing a Bluetooth Device for

more information.

•Reset the Bluetooth connection on your audio device by turning Bluetooth off and back

on. You can find this under the Bluetooth menu in the Settings for your phone or other

audio device.

If this does not work, and you have connected to Project Rocker before, find Project

Rocker in the list of available or previously connected devices in your audio device's

Bluetooth menu, tap the "gear" or “i” icon located next to it and then select Unpair or

Forget. Turn Project Rocker off and back on and try pairing again once it reappears in

your available devices list.

Note: If Project Rocker has been paired to another audio device recently that is still

within range, you may need to repeat this process with that audio device to fully

disconnect.

Guía de inicio rápido (Español)

Introducción

Gracias por comprar el Project Rocker. En ION, su entretenimiento es tan importante para

nosotros como para usted. Por eso es que diseñamos nuestros productos con una sola cosa en

mente—hacer que su vida sea más divertida y cómoda.

Nota: Antes de utilizar por primera vez el producto, cargue completamente la batería. Su

unidad se despachó intencionalmente con una carga reducida de la batería por razones de

seguridad en el tránsito.

Utilice el cable del suministro eléctrico incluido para conectar la unidad a una toma de

corriente y permita que la unidad se cargue durante hasta 5 horas. Esto contribuye a asegurar

la vida útil más larga de su batería.

Contenido de la caja

Project Rocker

Cable auxiliar estéreo de 3,5 mm (1/8 pulg.)

Cable de alimentación / carga

Guía de inicio rápido

Manual sobre la seguridad y garantía

Soporte

Para obtener la información más reciente acerca de este producto (documentación,

especificaciones técnicas, requisitos de sistema, información de compatibilidad, etc.) y

registrarlo, visite ionaudio.com.

Para obtener soporte adicional del producto, visite ionaudio.com/support.

Baterías recargables

Las baterías de plomo-ácido recargables son del mismo tipo que se usa en los automóviles.

Al igual que con la batería del vehículo, la forma en que se usa tiene una influencia significativa

en la duración de su vida útil. Con un uso y tratamiento correctos, una batería de plomo-ácido

puede durar varios años. He aquí algunas recomendaciones para prolongar la vida útil de la

batería interna.

Uso general Cargue completamente la batería antes de usarla.

Cargue la batería completamente después de cada uso.

lmacenamiento Para lograr la mayor longevidad del producto, no lo almacene a temperaturas

muy altas (superiores 32°C/90°F) o muy frías (inferiores a 0°C/32°F).

Es aceptable dejar su sistema de sonido enchufado. No sobrecargará la

batería.

Si deja que el nivel de la batería baje y no la carga durante 6 meses,

puede perder permanentemente su capacidad.

Reparación Si la batería no se carga, compruebe su fusible cerca de la entrada del

cable de alimentación. Si el fusible está intacto y la batería sigue sin

cargarse, póngase en contacto con ION Audio en ionaudio.com.

Disposición final Lleve la unidad a un centro de reciclaje o deséchela de acuerdo a las

ordenanzas locales.

Uso y cuidado a la intemperie

Aunque el Project Rocker es resistente al agua y capaz de tolerar salpicaduras, lea las

sugerencias que se incluyen a continuación para obtener el mejor rendimiento del Project

Rocker:

•El Project Rocker sólo puede usarse en exteriores con tomas de corriente o cables de

prolongación aptos para el uso en exteriores.

•Traiga a los Project Rocker bajo techo durante condiciones meteorológicas extremas.

•No coloque el Project Rocker sobre agua estancada.

•No conecte el adaptador de carga al Project Rocker en un ambiente húmedo. Asegúrese

de que la entrada para la entrada de alimentación, el cable de alimentación y la toma de

corriente estén completamente secos antes de realizar cualquier conexión.

•ADVERTENCIA: Coloque los dispositivos no resistentes al agua (teléfonos, reproductores

de música, etc.) en un lugar seco donde no sean afectados por el agua y causen un riesgo

de electrocución.

Instalación rápida

1. Asegúrese de que todos los artículos indicados en Contenido de la caja estén incluidos

en ella.

2. Lea el manual sobre la seguridad y la garantía antes de utilizar el producto.

3. Para asegurar una máxima vida útil de la batería, asegúrese de que esté completamente

cargada antes de utilizarla por primera vez.

4. Asegúrese de que el volumen maestro del Project Rocker esté en cero.

5. Conecte sus dispositivos.

6. Suba el volumen hasta un nivel confortable.

7. Regrese el volumen maestro a cero antes de apagar cuando termine de usar el Project

Rocker.

Tabla de contenidos

Idiomas:

Otros manuales de Sistema de altavoces de ION

ION

ION Total PA Spartan Manual de usuario

ION

ION Total PA Live Manual de usuario

ION

ION Total PA Supreme Manual de usuario

ION

ION EXPLORER EXTREME Manual de usuario

ION

ION BLOCK PARTY Manual de usuario

ION

ION Game Day Lights Manual de usuario

ION

ION Total PA Supreme Manual de usuario

ION

ION BLOCK ROCKER BLUETOOTH Manual de usuario

ION

ION WATER ROCKER Manual de usuario

ION

ION Block Rocker iPA76C Manual de usuario

ION

ION BLOCK ROCKER BLUETOOTH Manual de usuario

ION

ION Game Day Lights Manual de usuario

ION

ION TAILGATER BLUETOOTH Manual de usuario

ION

ION EXPLORER EXTREME Manual de usuario

ION

ION Total PA Premier Manual de usuario

ION

ION Total PA Premier Manual de usuario

ION

ION Offroad Manual de usuario

ION

ION TOTAL PA TITAN Manual de usuario

ION

ION TOTAL PA GLOW Manual de usuario

ION

ION Explorer Outback Manual de usuario

ION

ION TOTAL PA TITAN Manual de usuario

ION

ION Pathfinder Manual de usuario

ION

ION ANYROOM Manual de usuario

ION

ION TOTAL PA PRIME Manual de usuario

Manuales populares de Sistema de altavoces de otras marcas

JVC

JVC CA-MXK5R Manual de usuario

LG NB4532B Manual de usuario

JVC

JVC CA-FSH100 Manual de usuario

5Core

5Core Pro Series Manual de usuario

EAW

EAW MQV1394e Manual de usuario

Lynx

Lynx GXR-LA10A Manual de usuario

iLive

iLive ITB066B Manual de usuario

RDX

RDX QuickStation 4 Manual de usuario

Electro-Voice

Electro-Voice S-122 Manual de usuario

Sven

Sven SPS-619 GOLD Manual de usuario

Pioneer

Pioneer CS-7070 Manual de usuario

EAW

EAW UB82e Manual de usuario

Sondpex

Sondpex Active Speaker System and Digital Music... Manual de usuario

JVC

JVC NX-PN7 Manual de usuario

Marshall Amplification

Marshall Amplification AR-DM61-BT Manual de usuario

Yamaha

Yamaha NX-A01 - Speaker Sys Manual de usuario

SE Audiotechnik

SE Audiotechnik I-LINE Manual de usuario

Gemini

Gemini WRX-843 Series Manual de usuario