INVENTOR MOB-GPC12AF Manual de usuario

MOBILE AIR CONDITIONER

MOB-GPC12AF

.................................................................................

.....................................................................

................................................................................

.............................................................................

............................................................................

.................................................................... 20

.................................

..........

16-17

.......................................................................

3-7

8-10

...............

CONTENTS

SUMMARY

WORKING PRINCIPLE

STRUCTURE

OPERATING METHODS

NAMES AND FUNCTIONS OF THE REMOTE CONTROLLER

CARE AND MAINTENANCE

TROUBLESHOOTING

USER NOTICES

AFTER SERVICE

.............................................................

................................................................

OPERATIONOF THE REMOTE CONTROLLER

11-12

13-15

ACCESSORIES AND INSTALLATION OF HEAT EXHAUST HOSE

CIRCUIT DIAGRAM 21

....

SUMMARY

-1-

INVENTOR MOBILE AIR CONDITIONER is a small, moveable air conditioner. It possess

the functions of COOL, DRY and the Separate Ventilation, and depends on different places,

it can be moved as will. It is fit for home and office use, especially fit for the house with many

rooms. With the compact configuration, excellent workmanship, elegant appearance, it is

convenient for moving,energy saving, and low noise.

Note: Please read this manual carefully before operating the unit, the manual is used for

reference, and the technical parameters are subject to change without notice.

WORKING PRINCIPLE

With the help of upper motor, the airflow of indoor passes through the evaporator becomes the

cooling wind, but with the help of lower motor, the airflow of indoor passes through the condenser

becomes the heating wind. It was designed two duct systems in its structure The heating wind is discharged

by the rear outlet, the cooling wind is discharged by the front outlet, flow-guided by the louver, and it

brings the gentle cooling airflow, and the low temperature environment is maintained.

The Working Principle

Cooling wind

Upper motor

Lower

motor

Evaporator

Airflow 1

Airflow 2

Capillary

Heating wind

Condenser

－2－

STRUCTURE

Front

Rear

Air outlet

Controller panel

Handle

Remote box

Upper air inlet grille

Air exhaust outlet

Lower air inlet grille

50cm

The working range of COOL mode and HEAT modeis16℃-

30℃

At DRY mode,the static pressure range is 0～25 pa.

When operating, the unit should be placed on the horizontal place, more

than 50cm away from the wall or other obstructions.

The working range of COOL

mode,Heat mode and DRY

mode.

Location requirement

Power supply Before the unit is power-on, please check the following:

The power supply is rated voltage ±10%.

The power plugs and the

sockets can be supported by the current

that is more than 16A.

The thread section of the lead wires and any continued use lead wire

is no less than 1.5mm2.

The air conditioner must be safety earthed. Earth wire must be

connected to the special device of the building. In order to provide

the good earthing for the air conditioner.

The appliance must be positioned so that the plug is accessible,

If the supply cord is damaged, it must be replaced by the manufacturer

or its service agent or a similarly qualified person in order to avoid a hazard.

The appliance shall not be installed in the laundry.

The minimum clearance from the appliance to combustible surface is 50cm.

When children use the appliance, it must be supervised by adults or supervisors.

Including an air switch with suitable capacity, please note the following table. Air switch

should be included magnet buckle and heating buckle function, it can protect the

circuit-short and overload. (Caution: please do not use the fuse only for protect the circuit)

The appliance shall be installed in accordance with national wiring regulations.

The appliance is for indoor use only.

12K 16A

Air switch capacityAir-conditioner (W)

OPERATING METHODS

-3-

OPERATING METHODS

● Can not use the steel wire or the brass wire replace the fuse, the

capability of the fuse must be appropriate.

In order to avoid the power

cord damaged and electrical leakage, do not fix the power supply on the

knife edge or the sharp object.

● The wiring must be operated by the professional

and according

to the national regulations.

－4－

-5-

OPERA TING METHODS

Control paneland the function

1."ON/OFF"key

Press once to start and press once more to stop the unit.

2."MODE" key

Press this button to change the operation mode in order of:

LOOC → DRY→ FAN→ HEAT(No Heat mode for the cooling only unit.)

3. key

In "COOL"and "HEAT" mode,press

" once, the SET TEMP. will decrease 1

" once, the SET

TEMP.

will increase 1 The SET TEMP. can

be selected from 16℃(61 )～30℃(86 ).

Press. " ℃(1 )

℃(1 ),

F°

WATE full

ON/OFFkey

MODEkey

COOL mode

Set TEMP.

DRY mode

FAN mode

key

" "" "

→ COOL

I1M-12

-6-

OPERATING METHODS

1). To select a place near the door and window, install the exhaust duct.

2). Press"MODE"key to select"COOL"mode.

3).Press key to set the suitabletemp.16℃(61 )～30 86

℃.

When the unit is running in the COOL mode, in order to keep the good cooling effect,

please paymore attention to:

If there is thedirect sunlight near the window, please use the curtain to shield.

conditioner room.

Please close the door and window, in order to obtain the better dehumidifying effect:

Press"MODE"

key, select the "DRY" mode, the unit will run in the "DRY" mode, at the

same time, the upper motor is running at the low speed, it is not adjustable.

COOL mode

CAUTION

DRY mode

When in COOL or DRY mode, the dew water will drain into the tank.

When the tank gets full, the indicator will flash, and the buzzer will sound eight times,

LED window shows error code “H8”,at the same time the unit stop running.

WATER

DRAINAGE

"""°F°F

℃(61 )～30 86

℃.

°F°F

1). Press"MODE"key toselect "HEAT"mode.

2).Press key to setthe suitabletemp.16

HEAT mode "

"""

When the unit running in cool mode,do not use other heat sources in the air

Drain cap

Drain port

Install Drain Hose

1.Remove drain cap from drain port.

Drain Cap

2. Attach one end of the drain hose to the drain port with the clamp. See Drain Hose graphic.

3. Insert the drain plug into the other end of the drain hose and secure with clamp. See Drain Hose graphic.

4. Attach the drain hose clip to the back panel of the air conditioner near the drain port with the screw

provided.

Installof drainage hose (as shown in following figure):

Note Drainage hose must be installed before using otherwise block of drain may occur and

affects normal run of unit.

Drain Hose included:

Drainage pipe Clamp Pipe clip Rubber plug Screw

When COOL or DRY is running, condensate will drain to water tank.When water tank is fillbuz-

er will sound 8 timers for warn,water tank green indicated light on panel on with H8 displayed on

fro-m fixing clamp,then drain out water in tank.After that,plug the pipe plug onto pipe to prevent

leaka-ge of condensate and fix drainage pipe fixing clamp as shown in following figure.The unit

will resume running when water filled protect released and compressor stops for 3 minutes.

display window and whole unit stop running.Plug out plug on drainage hose and take off the hose

5. Snap the free end of the drain hose into the drain hose clip.

Drain Hose

Drain Hose Clip

Drain port

fixed clamp with screw

Drain plug

clip clip

drain hose

-7-

OPERATING METHODS

- -

●

AUTO

COOL

DRY

FAN

HEAT

FAN FAN speed button

Press this button once, fan speed will change

as below: Auto

Low speed Middle speed

High speed

Note:Under the Dry mode, the fan speed isn't

●

Simpleness swing mode is defaulted for wireless

remote control, in this mode, press this button,

(＋/－)

16 ～30℃

●

Note: Be sure that there are no obstructions between receiver and remote control; Don't drop

or throw the remote control; Don't let any liquid in the remote control and put the remote control

directly under the sunlight or any place where is very hot

Signal transmitter

Remote control

ON/OFF

ON/OFF button

Press this button, the unit will be started or stopped,

which can clear the timer or sleeping function of

last time.

●

.PMET button

(＋/－)

When press +button , the setting temp. will b

increasedby1 (1 ),When press-button,the

setting temp. will be decreased by 1

The temp. will be changed quickly

the button continuously and setting temp. range

℃

by pressing

●

Swing up and down button

℃

below.

Press this button, the running mode

will change as

Mode button

MODE

could turn on or turn off the Up and down

swing function.

When unit is turned off, synchronously press

"+" and Up and down swing buttons, it could

be switched between the simpleness swing

mode and stationary swing mode, at this time,

blinks 2 seconds.

In Stationary swingmode,pressthis button,the

angleforUpanddown swing as showinbelow:

Whenup anddownswing louverisworking,

whenturn offtheunit, thesiwnglouver will

●

immediatelystopat currentposition.

showsupand downswinglouverswings back

andforth as showintheabove figure.

adjustable, low fan speed is imperative,

but whenoperating thisbutton,thewireless

remote control will send this signal.

NAMES AND FUNCTIONS OFTHE REMOTE CONTROLLER

°F(1 )

°F

℃°F°F

FAN

AUTO

OPER

HEALTH

AIR

FILTER

TURBO

ON/OFF

X-FAN

HOUR

HUMIDITY

ON/OFF

MODE

FAN

X-FAN

TURBO

TEMP TIMER

SLEEP LIGHT

signal of heating operation.

)

(Note:no for coolling only unit

As for

cooling only unit, it won’t have

any action when it receives the

Tabla de contenidos

Otros manuales de Acondicionador de aire de INVENTOR

INVENTOR

INVENTOR V4MVI-09WFR/V4MVO-09 Manual de usuario

INVENTOR

INVENTOR RG57 Manual de usuario

INVENTOR

INVENTOR COOL Manual de usuario

INVENTOR

INVENTOR SUVI-09WFI Manual de usuario

INVENTOR

INVENTOR V6MCRI32-18WiFiR Instrucciones de funcionamiento y mantenimiento

INVENTOR

INVENTOR AR3VO32-09 Manual de usuario

INVENTOR

INVENTOR U4MRS-18 Manual de usuario

INVENTOR

INVENTOR V4MKI-24UR Manual de usuario

INVENTOR

INVENTOR V4MFI-66 Manual de usuario

INVENTOR

INVENTOR V4MFO-24 Manual de usuario

INVENTOR

INVENTOR DR2VO32-09 Guía

INVENTOR

INVENTOR LDVI-09WFI/LDVO-09 Manual de usuario

INVENTOR

INVENTOR P9VI32-12WF Manual de usuario

INVENTOR

INVENTOR O2MVI-09WiFiR/O2MVO-09 Manual de usuario

INVENTOR

INVENTOR V5MDI32-12WiFiRB Manual de usuario

INVENTOR

INVENTOR B2VI-18 Manual de usuario

INVENTOR

INVENTOR AR1MVO-09 Manual de usuario

INVENTOR

INVENTOR V4MLI-12/V4MLO-12 Manual de usuario

INVENTOR

INVENTOR CRVO32-09 Manual de usuario

INVENTOR

INVENTOR V4MVO-09 Manual de usuario

INVENTOR

INVENTOR V1DI-09 Manual de usuario

INVENTOR

INVENTOR P9VO32-09 Manual de usuario

INVENTOR

INVENTOR O1MVI-09WFR/O1MVO-09 Manual de usuario

INVENTOR

INVENTOR V1KI-09 Manual de usuario

Manuales populares de Acondicionador de aire de otras marcas

Spheros

Spheros CC 355 Manual de usuario

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manual de usuario

Panasonic

Panasonic CS-E12HKEW Manual de usuario

nedis

nedis ACMB1WT7 Manual de usuario

Samsung

Samsung AR KV Series Guía

Daikin

Daikin FCFV50A Manual de usuario

Fujitsu

Fujitsu Inverter ASBA30JFC Manual de usuario

Toshiba

Toshiba RAS-M10SMUV-E Manual de usuario

Daikin

Daikin FXLQ20MAVE Manual de usuario

Hitachi

Hitachi RAS-E24CAK Manual de usuario

CIAT

CIAT Magister 2 Series Guía

Bestron

Bestron AAC6000 Manual de usuario

Hisense

Hisense 7K Manual técnico

Frigidaire

Frigidaire FFRE0533S1E0 Manual de usuario

Samsung

Samsung AS09HM3N Manual de usuario

Frigidaire

Frigidaire CRA073PU11 Manual del propietario

Soleus Air

Soleus Air GB-PAC-08E4 Manual de usuario

McQuay

McQuay MCK020A Manual de usuario