Intex FastFill I637USB Manual de usuario
(37IO) I637USB ELECTRIC PUMP ENGLISH 4.875” X 7.25” 06/19/2021
English 37
IO
SAVE THESE INSTRUCTIONS
Page 1
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT
INTEX® OWNER’S MANUAL
FastFill™ USB Pump
Model I637USB 5V 2A
037-*IO-R0-2206
•NEVER PLACE AN INFANT TO SLEEP ON AIR MATTRESSES.
• Never introduce any flammable substance into the inflatable airbed, SUCH AS AEROSOL TIRE
REPAIR PRODUCTS, as it may ignite or explode.
•This is not a toy. Children must not be left unattended when using the airbed.
•If a storage bag is included,
keep the storage bag away from babies and children. The storage bag is
not a toy. When not in use, fold the bag and put it away out of the reach of children.
•Do not walk, stand on or jump on or use the airbed as a trampoline.
•Do not use on or near water. This is not a raft.
•Do not set up bed near stairs, doors, sharp edges or breakable objects. Provide adequate space
between bed and objects to avoid entrapment.
•Make sure the area is flat, smooth, even and free of sharp objects that could puncture the bed.
•Keep pets away from the airbed. Pets may puncture the surface of the bed.
•Avoid sleeping on the edge of the airbed. Edges produce less support than the middle of the bed.
•Do not obstruct the air passage opening or insert any objects into the air passage opening.
•
To reduce the risk of electric shock, do not expose to rain. Store indoors.
• Thisappliancecanbeusedbychildrenagedfrom8yearsandaboveandpersonswithreduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved.
• Childrenshallnotplaywiththeappliance.Cleaningandusermaintenanceshallnotbemadeby
children without supervision.
FOLLOW THESE RULES AND ALL INSTRUCTIONS TO AVOID SUFFOCATION, PROPERTY
DAMAGE, ELECTRIC SHOCK, BURNS OR OTHER INJURY.
WARNING
©2021 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Recreation Corp. All rights reserved/Tous droits réservés/Todos los derechos
reservados/Alle Rechte vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous licence de/Marcas registradas
utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/
a/an Intex Development Co. Ltd., Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801•DistributedintheEuropeanUnion
by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union durch/Intex Trading B.V., Venneveld
9, 4705 RR Roosendaal – The Netherlands
www.intexcorp.com
(37IO) I637USB ELECTRIC PUMP ENGLISH 4.875” X 7.25” 06/19/2021
English 37
IO
SAVE THESE INSTRUCTIONS
Page 2
NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale.
Due to a policy of continuous product improvement, Intex reserves the right to change
specifications and appearance, which may result in updates to the instruction manual,
without notice.
PARTS REFERENCE
Part Descriptions:
1. Control dial
2. Inflation mark ( )
3. Off mark ( )
4. Deflation mark ( )
5. Manual inflation port and cap
6. Cord compartment cover
7. USB cable
8.Airbed
8
3
46
5
7
1
2
INSTRUCTIONS
The pump uses the power supplied by a standard USB socket. Older USB adapters do not
supply enough power for the pump to fully inflate the airbed. Newer “fast charge” adapters
need to be used. Check that your adapter’s output is 2A or more for optimum operation.
Most USB charge ports in vehicles are too weak: a 12 volt USB adapter (12V Car Charger)
may be needed. If the pump won’t inflate the bed fully within 7 minutes, you probably need
higher output.
General
• Theairpumprequiresanexternalpower adapter (not included) to operate.
• Airpumpinputvoltage/currentrating: 5V / 2A or more.
• Makesuretheoutputoftheexternalpoweradapter,suchasUSB Wall Charger, Portable
USB Charger, 12V Car Charger or USB Port is rated 5V / 2A or more.
• Nospecific air pump maintenance is required. Air pump has no user serviceable parts.
• Make sure the area is flat, level, clean and free from sharp objects. To prevent puncture
or damage to the airbed, never drag the airbed across the ground. Lift the inflated airbed
when moving or changing location.
• During outdoor use, place a protective layer such as a tarp (not included) between the
selected surface and the airbed in order to prevent damage to the airbed.
• For cleaning use only clean cloth with mild soapy solution. Do not use any chemicals.
• Incaseofrepairs,useonlycommonPVCrepairglueandpatches.For flocked surfaces:
rub away the flocking material with an eraser first before applying the glue and/or patch.
(37IO) I637USB ELECTRIC PUMP ENGLISH 4.875” X 7.25” 06/19/2021
English 37
IO
SAVE THESE INSTRUCTIONS
Page 3
2. Connect the USB cable to one of the following external power adapters (not included):
• USB Wall Charger rated 5V / 2A or more. See Fig (2).
•Portable USB Charger rated 5V / 2A or more. See Fig (3).
• 12V Car Charger rated 5V / 2A or more. See Fig (4).
• USB Port rated 5V / 2A or more. See Fig (5).
3. Turn the control dial to the inflation mark ( ). See Fig (6).
4. When the airbed is fully inflated, turn the control dial back to the off mark ( ) position
closing the inflation valve. See Fig (7).
5. Lie down on the airbed to test the firmness.
6. If the airbed feels too firm, release some air by simply turning the control dial to the
deflation mark ( ) until desired firmness is achieved, then turn the control dial back to
the off mark ( ) position. If the bed feels too soft, repeat steps #3 to #6 as necessary.
FIG (2)
USB Wall Charger
FIG (3)
Portable USB Charger
FIG (4)
12V Car Charger 5V/2A USB Port
FIG (5)
FIG (7)
FIG (6)
Inflation
mark
INFLATION
1. Open line cord compartment cover and pull out the USB cable. See Fig (1).
FIG (1)
(37IO) I637USB ELECTRIC PUMP ENGLISH 4.875” X 7.25” 06/19/2021
English 37
IO
SAVE THESE INSTRUCTIONS
Page 4
DEFLATION
1. Connect the USB cable to an appropriate external power adapter. See Fig (2-5).
2. Turn the control dial to the deflation mark ( ). See Fig(8).
3. With the airbed fully deflated begin rolling the airbed from the end opposite of the pump
towards the end where the pump is located. See Fig (9).
4. When all the air is removed from the airbed, turn the control dial back to the off mark
(
) closing the valve.
5. Disconnect the USB cable from the external power adapter, place it inside the cord
compartment and close the cover. Make sure the USB cable is free of twists, kinks or
knots.
FIG (9)
FIG (8)
Deflation
mark
Proper inflation of the airbed.
The ambient temperatures of air have an effect on the airbed internal pressure. At low
ambient temperature the air will contract within the airbed and the airbed will feel softer:
add air as necessary. At high ambient temperature the air within the airbed will expand
significantly and the airbed will become hard and may burst: release air to avoid damage
to the airbed or to soften the feel. Do not expose the airbed to extreme temperatures (hot
or cold). Stretching is a natural characteristic of new vinyl. During initial use, the airbed
may become soft and require additional inflation to maintain desired firmness. This is
normal for the first few days of use. Dimensions shown are approximate and will vary due
to the vinyl temperature and the air temperature.
In no event shall Intex, their authorized agents or employees be liable for damages
(such as pin holes) to the airbed caused by negligence, ordinary wear and tear,
abuse and carelessness, or external forces.
IMPORTANT NOTE
STORAGE INSTRUCTIONS
1. Deflate the airbed following the “DEFLATION” instructions.
2. Make sure the airbed is clean and dry.
3. Lay the airbed flat with the sleeping surface facing upwards and follow the folding steps
on Figs (10 - 14). Fold the airbed loosely and avoid sharp bends, corners and creases
which can damage the airbed.
FIG (10) FIG (11) FIG (12) FIG (14)
FIG (13)
4. Place the airbed inside the storage bag (if included) or the original packaging and store
in a dry place.
(37IO) I637USB ELECTRIC PUMP ENGLISH 4.875” X 7.25” 06/19/2021
English 37
IO
SAVE THESE INSTRUCTIONS
Page 5
TROUBLESHOOTING GUIDE
PROBLEM CAUSE SOLUTION
Air pump does
not work
•Theexternalpoweradapter/
supply output is not correct.
•Pumprunningcontinuouslyfor
30 minutes, motor protection
system activated.
•Pumpcontinuouslyconnected
to a portable USB charger and
idled, hence the portable USB
charger is in rest mode.
•Makesuretheoutputoftheexternalpower
adapter, such as USB Wall Charger, Portable
USB Charger, 12V Car Charger or USB Port
is rated 5V / 2A or more. See “INFLATION”
section.
•Switchoffanddisconnectthelinecordfrom
the power adapter/ supply. Let the pump rest
for 1 minute before restarting.
•DisconnectandreconnecttheUSBcableto
the portable USB charger.
Airbed not fully
inatedafter
5 - 7 minutes
ofination
•Theexternalpoweradapter/
supply output amperage (A) is
less than 2A.
•Themanualinflationportcapis
not securely closed.
•Makesuretheoutputoftheexternalpower
adapter, such as USB Wall Charger, Portable
USB Charger, 12V Car Charger or USB Port
is rated 5V / 2A or more. See “INFLATION”
section.
•Pushthecapfirmlyintothemanualinflation
port.
Air leaking from
the pump panel
or compartment
cover
•Thecontroldialisnotintheoff
mark ( ) position.
•Themanualinflationportcapis
not securely closed.
•Turnthecontroldialtotheoffmark
( )
position after inflation is completed.
•Pushthecapfirmlyintothemanualinflation
port.
INFLATION OPTION
If electrical power is not available, a conventional foot, manual, or battery-operated air
pump can be used by connecting it to the manual inflation port located inside the line cord
compartment. Do not use high-pressure air compressors. See Fig (15). Follow these steps:
1. Open line cord compartment cover and locate the
manual inflation port.
2. Make sure the control dial of the internal electric
pump is still in the off mark ( ) position.
3. Remove the cap from the manual inflation port and
insert the nozzle of the pump into the port. Inflate the
airbed to desired firmness.
NOTE: Do not overinflate. The firmness should be
approximately the same as the level achieved with the internal electric pump.
4. Remove nozzle from manual inflation port and close the cap and the line cord cover.
FIG (15)
Otros manuales para FastFill I637USB
2
Tabla de contenidos
Otros manuales de Bomba de agua de Intex
Intex
Intex Krystal Clear 604 Manual de usuario
Intex
Intex Krystal Clear 601 Manual de usuario
Intex
Intex Krystal Clear Deluxe Manual de usuario
Intex
Intex Krystal Clear C1500 Manual de usuario
Intex
Intex QUICK FILL PLUS Manual de usuario
Intex
Intex Fast-Fill AP640R Manual de usuario
Intex
Intex SF80220RC-1 Manual de usuario
Intex
Intex AP619A Manual de usuario
Intex
Intex Quick-Fill AP609 Manual de usuario
Intex
Intex Quick-Fill AP640 Manual de usuario
Intex
Intex Krystal Clear SF10220 Manual de usuario
Intex
Intex Quick-Fill AP640 Manual de usuario
Intex
Intex Krystal Clear 601 Manual de usuario
Intex
Intex 128644GS Manual de usuario
Intex
Intex Quick-Fill AP644 Manual de usuario
Intex
Intex Fast-Fill AP640R Manual de usuario
Intex
Intex SF20220R Manual de usuario
Intex
Intex FastFill AP619DA Manual de usuario
Intex
Intex Quickfill Plus AP620D Manual de usuario
Intex
Intex SF15220 Manual de usuario
Manuales populares de Bomba de agua de otras marcas
Sykes AmeriPumps
Sykes AmeriPumps GP100M Guía de solución de problemas
DUROMAX
DUROMAX XP WX Series Manual de usuario
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Manual de usuario
Franklin Electric
Franklin Electric IPS Manual de usuario
Xylem
Xylem e-1532 Series Manual de usuario
Milton Roy
Milton Roy PRIMEROYAL Manual de usuario