Interpack RSA 20-B Manual de usuario
USER MANUAL
RSA 20-B
For Serial Numbers:
TM123 and TM623 XX X XXX
REV 3 06232022
2
Interpack RSA 2024-SB Rev 3
Rev 3 UM122TW
3
Replacement Parts 4
Explanation of Signal Word Consequences 14
Operator Skill Level Descriptions 15
Receiving and Handling 20
Set up 20
Optional Equipment: Caster Installation 21
Optional Equipment: In-feed/Out-feed Table Installation 22
Optional Equipment: Installation of External In-feed and Exit Conveyors 24
Preparing Cases to be Processed 34
The Machine is Turned on and Nothing Happens 39
Front Tape Leg Not Sticking 40
Rear Tape Leg Not Sticking 41
Case is Getting Crushed? 42
Tape Does Not Cut 43
Tape Jam 44
Wrinkles in the Tape 45
Tape Not Dispensed 46
Lubrication: 47
Cleaning: 47
Recommended Spare Parts: 47
Changing the Air Regulator Filter 48
Removing the Top Tape Head 49
Removing the Top Tape Head 50
Cleaning the Cutter Blade, Top Tape Head 51
Cleaning the Cutter Blade, Bottom Tape Head 52
Cutter Blade Maintenance 53
Cutter Blade Replacement 54
Drive Belt Replacement 55
Drive Belt Adjustment 56
4
Interpack RSA 2024-SB Rev 3
This is the Interpack Model Side-Belt Case Sealer you ordered. It has been set up and
tested in our factory with Intertape manufactured water activated tapes. If any problems occur when setting up or operating this
equipment, please contact the authorized distributor from where you purchased this item.
If contact with the authorized distributor is not possible, is available. Should the need to contact
arise, This information
can be found on the nameplate of the tape head as well as on the machine, both sets of information may be necessary to
assist. A section at the bottom of this page is available to writ this information down. is available during
normal business hours (M-F 8am-5pm) Eastern Time.
A breakdown of parts, including part numbers, can be found in the appendix of this manual. If you know the part number that
you require please contact your authorized distributor or IPG Customer Service 877-447-4832 Option 3
Please use this area to enter the detailed information on your Case Sealer and Tape Heads. This should be lled out at the
time of install. This information can be found on the nameplate of the machine, typically on the side the electrical box is on.
On pressure sensitive tape the nameplate is located on the same side the tape is loaded from. On the WAT Tape Heads serial
information can be found near the air intake of the head.
(if applicable)
Rev 3 UM122TW
5
Your Interpack Case Sealer and Tape Heads are designed to provide years of trouble free operation. This is not without proper
preventative maintenance, a recommended schedule can be located in the maintenance section of this manual, performed by
then end user of the equipment. If any problems arise with this machine during the normal course of operation, your properly
trained and qualied internal service personnel should be able to repair any issues after consulting the troubleshooting section
of this manual in conjunction with phone and/or email support from IPG Machinery Support.
Field Service Support is available from your IPG Authorized Distributor at additional cost if the problem cannot be remedied after
consulting the troubleshooting section of this manual.
IPG oers comprehensive programs that help keep your equipment up and running.
Proactive maintenance eorts help to prevent equipment failures and costly emergency repairs. Keeping your machine in
optimal working condition also enhances employee safety, reduces facility downtime and eciently allocates internal resources.
Please contact your IPG Representative to discuss the best options for your IPG equipment.
6
Interpack RSA 2024-SB Rev 3
EQUIPMENT WARRANTY AND LIMITED REMEDY: The following warranty is made in lieu of all other warranties, express
or implied, including, but not limited to, the implied warranty of merchantability, the implied warranty of tness for a particular
purpose, and any implied warranty arising out of a course of dealing, a custom or usage of trade:
Intertape sells its Interpack Tape Heads, Case Tapers and Case Erectors with the following warranties:
1. The HSD® 2000 Tape Heads’ knife blades, springs and wipe down rollers will be free from all defects for a period of
ninety (90) days.
2. All other HSD® 2000 Tape Head parts will be free from all defects for one (1) year after delivery.
3. Water Activated Tape Heads’ blades will be free from defects for ninety (90) days after delivery.
4. Drive Belts will be free from defects for ninety (90) days after delivery
5. The Gear Motors will be free from defects for one (1) year after delivery.
6. All other components for Case Tapers and Case Erectors will be free from defects for one (1) year after delivery.
If any part is proven defective within its warranty period, then the exclusive remedy and Intertape’ s and the seller’s sole
obligation shall be, at Intertape’ s option, to repair or replace the part, provided the defective part is returned immediately to
Intertape’ s factory or an authorized service station designated by Intertape.
A part will be presumed to have become defective after its warranty period unless the part is received or Intertape is notied of
the problem no later than ve (5) calendar days after the warranty period.
If Intertape is unable to repair or replace the part within a reasonable time, then Intertape, at its option, will replace the
equipment or refund the purchase price. Intertape shall have no obligation to install the repaired or replacement part.
Intertape shall have no obligation to provide or pay for the labor required to install the repaired or replacement part.
Intertape shall have no obligation to repair or replace (1) those parts failing due to: operator misuse, carelessness, or due to any
accidental cause other than equipment failure, or (2) parts
7. Failure or damage is due to misapplication, lack of proper maintenance, abuse, improper installation or abnormal
conditions such as temperature, moisture, dirt or corrosive matter, etc.
8. Failure due to inadequate cleaning, improper operating environment, improper utilities or operator error.
9. Failure due to operations above the rated capacities, or in any other improper manner, either intentional or otherwise.
10. Failure is due to equipment, which has been altered by anyone other than an authorized representative of Intertape
Polymer Group.
11. Failure is due to an attempt by the purchaser to correct alleged defective equipment. In this event the purchaser is
responsible for all expenses incurred.
LIMITATION OF LIABILITY: Intertape and seller shall not be liable for direct, indirect, special, incidental or consequential
damages based upon breach of warranty, breach of contract, negligence, strict liability or any other legal theory.
The foregoing Equipment Warranty and Limited Remedy and Limitation of Liability may be changed only by written agreement
signed by authorized ocers of Intertape and seller.
Rev 3 UM122TW
7
This machine is designed to provide years of trouble free operation. If any problems arise with this machine during the normal
course of operation, your properly trained and qualied internal service personnel should be able to repair any issues after
consulting the Troubleshooting section of this manual.
The Interpack RSA 20-B Case Sealing Machine with HSD®2000-ET II+ Tape Head is designed to apply Intertape brand
pressure sensitive case sealing tape to the bottom center seam of regular slotted corrugated cases. The RSA 20-B is auto
adjustable to a random variety of case sizes.
Common terms that will be used throughout this manual.
– This will refer to the HSD®2000-ET II+ Tape Head for the remainder of this manual
– Refers to IPG manufactured Case Sealers
– Refers to the fully assembled Case Sealer with the Tape Head(s) installed
– The individual who has been trained on the daily use of the Machine System
– The individual(s) who work for the end user of the Machine System who are responsible for
conducting general and preventative maintenance
8
Interpack RSA 2024-SB Rev 3
The RSA 20-B can be outtted with a variety of optional equipment. The below list is standard and should be discussed with
your distributor or authorized IPG representative if you would like them to be added to your machine.
It is recommended to keep a spare tape head in the event any failure or malfunction causes the machine to stop production.
This is to help reduce any possible downtime.
Feed Table 16” (.4M) UM894T 1
Feed Table 24” (.6M) UM998T 1
Feed Table 36” (.9M) UM898T 1
Casters UM841 1 set of 4 (36” Feed Table will require 2
additional casters)
Secondary Emergency Stop UM9003 1
4” Drive Bases UAM1079 (right) and UAM10798 (left) 1
Reverse Electrical Box UM085 1
Reverse Operator Control Pneumatic UM087 1
Low Tape No Tape Box UH1426 1
HSD® 2000-ET II+ 2” UH275TW
HSD® 2000-ET II+ 3” UH775TW
ET Extreme 2” UH230TW
ET Extreme 3” UH430TW
Casters
Infeed/Outfeed
Tables
ETX Tape
Head
Rev 3 UM122TW
9
There are a number of safety labels used on the RSA 20-B Case Sealer. These labels are placed at dierent locations on the
machine to warn operators and service personnel of possible dangers. Please read the labels on the machine and the following
safety precautions before using the machine.
Should any of the safety labels on the Case Sealer be damaged or destroyed, replacements can be ordered through your
distributor.
10
Interpack RSA 2024-SB Rev 3
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Equipos industriales de Interpack
Interpack
Interpack USA 2024-SB Manual de usuario
Interpack
Interpack CE-12P Manual de usuario
Interpack
Interpack USA 2024-SB DH Manual de usuario
Interpack
Interpack CE-12P Manual de usuario
Interpack
Interpack ipg RSA 2625-TB Manual de usuario
Interpack
Interpack ETII+ LD Manual de usuario
Interpack
Interpack HSD2000 XS II Series Manual de usuario
Interpack
Interpack HSD2000 ET II RC Manual de usuario
