Interlogix TX-4200-01-1 Instrucciones de montaje

P/N 466-4431 • REV B • 14FEB14 1 / 4

Description

The Personal Panic Device is a wireless

device that can be used to activate police or

auxiliary alarms throughout the premises.

When the help button is pressed, both red

LEDs flash and information is transmitted.

The transmitted signal includes alarm and

battery status information. When the help

button is released, an alarm-restore-all

message is sent. Note: To activate, press

and hold the help button until the red LEDs

stop flashing, then release the button.

The Personal Panic Device is shipped with

a watch type wristband installed. A pendant

adaptor kit and lanyard are also included for

an optional necklace arrangement. The

pendant kit includes a pendant loop and a

pendant plug (shown below).

The Personal Panic Device is water

resistant and has been tested in water at

three meters for one hour.

Installation

Assembly Guidelines

•Program the Personal Panic Device

into the appropriate panel groups.

Refer to the “Programming” section for

more information.

•The transmitter on the Personal Panic

Device has a maximum range of 375

feet. Test the device at the outer limits

of the installation to ensure it works

properly. The outer limits may vary due

to different environments that may

affect the range. Refer to the “Testing”

section for more information.

•Verify the user can activate the help

button by pressing it with their thumb

or finger.

•When worn as a pendant, it is

important that the user does not

activate the help button by pressing it

against their chest. This may reduce

the signal’s effective range.

Watch Style Wristband

Adjust the length of the wristband by

measuring and cutting the band in the

following manner:

1. Position the wristband tightly around

the wrist and in the intended position

as shown in Step 2.

2. Using a washable marker, place a

mark on the edge of each strap, near

the center of the wrist.

Personal Panic Device Installation Sheet

2 / 4 Personal Panic Device Installation Sheet

3. Align the band so the ends of the band

are even. Cut the band in the center of

the two marks as shown below.

4. Attach the band to the clasp. Feed the

band through the retainer opening and

close the lever to lock the band in

place. Repeat for the other side.

Pendant

The Personal Panic Device can be worn as

a pendant by removing the wristband and

installing the pendant adaptor components

and lanyard in the following manner:

1. Remove the two screws on the back of

the Personal Panic Device.

2. Carefully separate the cover and base.

3. Remove the wristband.

4. Separate the components from the

pendant adaptor kit and discard the

circular center section.

5. Insert the pendant loop adapter into

the small loop end of the lanyard.

6. Insert the plugs into the base and

reattach the cover and base. Note:

Compress the panic button and base

assembly together before tightening

the screws.

Programming

Review the following information for adding

a Personal Panic Device to the panel. Refer

to the specific panel Installation Instructions

for further detail.

1. Set the panel to Program Mode.

P/N 466-4431 • REV B • 14FEB14 3 / 4

2. When prompted, enter the appropriate

group number and select the desired

sensor number.

3. Press the help button on the Personal

Panic Device to trip the selected

sensor.

4. Exit from Program Mode.

Maintenance and Testing

Testing

Review the following for testing the help

button. Refer to the specific panel

Installation Instructions for further detail.

1. Set the panel to Sensor Test Mode.

2. Press and hold the help button for a

second to monitor the beeps for the

packet count.

3. Listen for the panel siren. You should

hear 6 to 8 beeps.

4. Test the help button from several

locations to ensure a consistent

response.

5. Test the help button weekly to ensure

proper operation.

6. Verify the end-user can operate the

unit without any difficulty.

Cleaning

1. Gently rub a lanoline-based cleaner,

such as Go-Jo, onto all surfaces of the

Personal Panic Device to remove any

debris.

2. Rinse off using warm water.

3. Wipe clean using a dry, lint-free cloth.

Replacing the Battery

CAUTION: To avoid an alarm

condition set the panel to Sensor Test

Mode prior to changing the battery.

Pour éviter une condition d'alarme

metter le panneau en Mode d'essai

des capteurs avant de changer la

batterie.

CAUTION: Use static electricity

precautions when handling electronic

components.

Utiliser les précautions de l'électricite

statique lors de la manipulation des

composants électroniques.

1. Depending on the situation, it may be

necessary to contact the central

monitoring station before starting the

installation.

2. Remove the two screws on the back of

the Personal Panic Device and

observe how the pendant or wristband

components are attached.

3. Carefully separate the cover and base.

4. Remove the electronic subassembly

from the base.

5. Remove the battery from the electronic

subassembly.

6. Install the new battery. Observe

polarity.

Note: Install Panasonic CR1632.

7. Place the electronic sub assembly into

the base. Note: A generic diagram is

shown above. For diagrams showing

the wristband and pendant

configurations, see the assembly

diagrams in the “Installation/Pendant”

section.

8. Inspect the water seal area and the

plugs to ensure they are free from

debris.

9. Reattach the cover, lanyard assembly

or wristband and the base. Note:

4 / 4 Personal Panic Device Installation Sheet

Press the pushbutton and cover

together before tightening the screws.

10. Test the help button for proper

operation.

11. If the central monitoring station was

notified, inform them this operation is

complete.

Specifications

Model no.

TX-4200-01-1 (white)

TX-4200-01-2 (black)

RF frequency

319.5 MHz

Compatibility

Interlogix Learn Mode Panels

and Receivers

Battery type

3.0 V lithium (CR1632)

Recommended

battery

Panasonic CR1632

Typical standby

current (μA)

≤1

Estimated battery

life

5 years

Supervisory

interval

Less than 64 minutes

Operating

temperature range

32° to 120°F (0° to 49°C)

Storage

temperature range

-30 to 140°F (-34 to 60°C)

Relative humidity

5-90% non-condensing

Dimensions

(L x W x D)

1.60 x 1.40 x 0.410 in. (4.1

x 3.6 x 1.0 cm)

Regulatory Information

Manufacturer

UTC Fire & Security Americas

Corporation, Inc.

1275 Red Fox Rd., Arden Hills,

MN 55112-6943, USA

FCC

Compliance

This device complies with part 15

of the FCC Rules. Operation is

subject to the following two

conditions: (1) This device may

not cause harmful interference,

and (2) this device must accept

any interference received,

including interference that may

cause undesired operation.

Changes or modifications not

expressly approved by Interlogix

can void the user’s authority to

operate the equipment.

FCC ID: B4Z-984-PANIC

IC: 1175C-984PANIC

This Class B digital apparatus

complies with Canadian ICES-

003.

Cet appareil numérique de la

classe B est conforme à la norme

NMB-003 du Canada.

Le fonctionnement est soumis

aux deux conditions suivantes :

(1) cet appareil peut ne pas

provoquer d’interférences et (2)

cet appareil doit accepter toutes

interférences, y compris les

interférences pouvant

provoquer un fonctionnement

non désiré de l’appareil.

US Patents

4,855,713; 4,864,636 and

others pending.

Contact Information

For general information, see

www.interlogix.com. For customer support,

see www.interlogix.com/customer-support

or call +1 855 286 8889.

Interlogix is part of UTC Building and

Industrial Systems, a unit of United

Technologies Corporation. All rights

reserved.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sensor de seguridad de Interlogix

Interlogix

Interlogix TX-2511-03-1 Instrucciones de montaje

Interlogix

Interlogix EV1012 Series Instrucciones de montaje

Interlogix

Interlogix DD1012AM-D Instrucciones de montaje

Interlogix

Interlogix EV1116-D Series Instrucciones de montaje

Interlogix

Interlogix SB Series Manual de usuario

Interlogix

Interlogix DD490 Series Instrucciones de montaje

Interlogix

Interlogix EV520-P Series Instrucciones de montaje

Interlogix

Interlogix ACL870FL-BS Manual de usuario

Interlogix

Interlogix DI601 Instrucciones de montaje

Interlogix

Interlogix DD100PI Instrucciones de montaje

Interlogix

Interlogix Firefighter SLX-AD-T3 Guía

Interlogix

Interlogix DDV1016AM Instrucciones de montaje

Interlogix

Interlogix TVK-600 Hoja de instrucciones

Interlogix

Interlogix GS960AM Instrucciones de montaje

Interlogix

Interlogix EV100 Instrucciones de montaje

Interlogix

Interlogix DDI602AM Instrucciones de montaje

Interlogix

Interlogix EV660 Series Instrucciones de montaje

Interlogix

Interlogix EV1012-D Series Instrucciones de montaje

Interlogix

Interlogix ACL870SU-BSMF Manual de usuario

Interlogix

Interlogix VE1120-D Series Instrucciones de montaje

Interlogix

Interlogix xGen Lite Guía de instalación

Interlogix

Interlogix PB501 Instrucciones de montaje

Interlogix

Interlogix DC111 Instrucciones de montaje

Interlogix

Interlogix GS960 Instrucciones de montaje

Manuales populares de Sensor de seguridad de otras marcas

THORLABS

THORLABS PDA10JT Manual de usuario

Waeco

Waeco UV-DETECT Manual de usuario

Intermatic

Intermatic IOS-DSIMF Manual de usuario

urmet domus

urmet domus 1083 Manual de usuario

Siemens

Siemens AZL66 Series Manual de usuario

BTI

BTI Profiline Multi Finder Manual de usuario

Challenger

Challenger SL01 Manual de usuario

DMP Electronics

DMP Electronics 1122INT Manual de usuario

Rielta

Rielta Ladoga MK-RK Manual de usuario

Mirion Technologies

Mirion Technologies ACCURAD PRD Manual de usuario

Bosch

Bosch DS835 Manual de usuario

DBI SALA

DBI SALA EZ Stop Manual del operador

Lamptime

Lamptime ST05C Manual de usuario

Ubiquiti

Ubiquiti MFI-MSC Manual de usuario

Subsite

Subsite 910R Instrucciones de instalación

Satel

Satel OPAL Pro Manual de usuario

Aleph

Aleph XC-1XTEU Manual de usuario

Pima

Pima LARIS QUAD Manual de usuario