Interlogix HDX-135Z-433 Manual de usuario

Attention: Please take a few minutes to thoroughly read this user guide which should be

saved for future reference.

NOTE: Leave this user guide with the home owner.

You do NOT need a home wi-fi system to use these units. Multiple wireless units create

their own independent wireless alarm network.

HDX-135Z-433

Wireless Interconnected

Heat/Freeze sensor 433-63

User Guide

Thank you for purchasing this Interlogix heat alarm

This model is powered by a non-replaceable, long life sealed lithium battery system, and

includes SMART HUSH®Control to temporarily silence nuisance alarms. It is capable of

Wireless Interconnect with compatible units.

WARNING! THIS HEAT ALARM IS NOT DESIGNED TO PROTECT LIFE SAFETY

AGAINST FIRE AND SMOKE. SEE LIMITATIONS IN SECTION 6 FOR DETAILS.

READ SECTION 8: Installation / Activation / Wireless, before powering the units.

You do NOT need a home wi-fi system to use these units. Multiple wireless units

create their own independent wireless alarm network.

Teach children how to respond to the alarm and that they should never play with the unit. Your

Interlogix heat alarm was designed for use in a residential environment. It is not designed for

use in a recreational vehicle (RV) or boat.

NOTE: Please thoroughly read this user guide and save the document for future reference and

to pass on to any subsequent owner.

The manufacturer recommends replacing this alarm ten years from the date code on back of

the alarm.

Customer Service: 1-855-286-8889

Please write down the below information and have this at hand when you call.

Model (on back): _________________

Date Code (on back): _________________

Date of Purchase: _________________

Where Purchased: _________________

Date to Replace: _________________

Contents

1. Heat Alarm: What To Do When The Alarm Sounds.........................................................4

2. Other Alarm Visual And Audible Indicators .....................................................................5

3. Troubleshooting Guide ...................................................................................................... 7

4. Introduction, Product Features & Specifications............................................................ 9

5. Limitations Of Heat Alarms.............................................................................................. 13

6. Recommended Locations For Heat Alarms ...................................................................14

7. Locations To Avoid ........................................................................................................... 17

8. Installation / Activation / Wireless ................................................................................... 18

8.1 Set Up A Wireless Alarm Network (Wireless Interconnect) .................................................. 19

8.2 Adding Alarms to an Existing Wireless Interconnected Network ......................................... 21

8.3 Resetting an Alarm’s Wireless Interconnect Settings ........................................................... 22

9. Operation and Testing……………………………………………………............................. 23

10. Recognizing Nuisance Alarms …………………………………………............................. 25

11. Battery ………………………………………….................................................................... 26

12. Permanently Disable Alarm / Discharge Battery .......................................................... 27

13. Cleaning Your Alarm …………………….......................................................................... 28

14. Good Safety Habits ……………………........................................................................… 29

15. Service And Warranty …………………........................................................................…31

1. Heat Alarm: What To Do When the Alarm Sounds

Heat alarm pattern is three long beeps, a 1.5 second pause, and three long beeps repeating.

The red LED blinks in time with alarm pattern.

•Alert small children in the home as well as anyone else that might have difficulty recognizing the

importance of the alarm sounding or that might have difficulty leaving the area without help.

•Leave immediately by your escape plan. Every second counts, so don’t waste time getting dressed or

picking up valuables.

•In leaving, don’t open any inside door without first feeling its surface. If hot, or if you see smoke seeping

through cracks, don’t open that door! Instead, use your alternate exit. If the inside of the door is cool,

place your shoulder against it, open it slightly and be ready to slam it shut if heat and smoke rush in.

•If the escape route requires you to go through smoke, stay close to the floor where the air is cleaner.

Crawl if necessary, and breathe shallowly through a cloth, wet if possible.

•Once outside, go to your selected meeting place and make sure everyone is there.

•Call the fire department from your cell phone outside, or from your neighbor’s home-not from yours!

•Don’t return to your home until the fire officials say that it is all right to do so.

•There are situations where an alarm may not be effective to protect against fire as stated in the NFPA

Standard 72. For instance:

a) smoking in bed

b) leaving children home alone

c) cleaning with flammable liquids, such as gasoline

NOTE: See Section RECOGNIZING NUISANCE ALARMS, for nuisance alarm situations.

2. Other Alarm Visual and Audible Indicators

Operational Mode Visual Indications Audible Indications Action/Note:

Normal Operation

(standby)

One GREEN LED blink

every 60 seconds.

Freeze Warning One RED LED blink

every 20 seconds.

None None. Flashing continues

while condition exists.

Tamper Condition One RED LED blink

every 30 seconds

(after a 3 minute

delay).

Alarm chirps once when tamper

condition is rst sensed, then the

alarm will chirp every 30 seconds

after a 3 minute delay.

Reattach alarm to its trim

plate, otherwise ashing and

chirping will continue while

condition exists.

System Test Mode Rapidly ashing RED

LED for 10 seconds

duration

1 alarm chirp when magnet

detected, 2 alarm chirps when System

Test mode enabled

Hold magnet next to button

for 4 seconds. See Figure 5.

Local Alarm Test

(button press when

no alarm condition

is present)

Flashes RED, AMBER,

GREEN, then current

protocol

Temporal T3 pattern Allow completion of test or

perform button press to

cancel, return to normal

operation

System Alarm Test (but-

ton press in System Test

Mode when no alarm

condition is present)

Flashes RED, AMBER,

GREEN, then current

protocol on each alarm

in the network

Temporal T3 pattern Allow completion of test or

perform button press to

cancel, return to normal

operation.

Operational Mode Visual Indications Audible Indications Action/Note:

Heat Alarm Memory

(alarm has experienced

an alarm event within

the last hour)

Alternating ashing

RED and AMBER

LEDs. 1 second RED/1

second AMBER/ 10

seconds OFF,

repeating for 1 hour

None Press test button to clear alarm

memory, or allow 1 hour time out

to return to normal operation.

NOTE: standard test sequence

will follow. (Push/release button

again to cancel test).

Heat Alarm Hush Mode

(Heat HUSH

CONTROL)

Red LED blinks

every 2 sec.

After button push: Heat alarm

pattern stops. (If the unit still

detects a dangerous situation

the alarm will sound again)

This feature is to be used only

when a safe condition is known

to exist.

Locate None After button push on non-ini-

tiating unit, only initiating unit

continues alarm pattern.

Use this to quickly locate the

alarm source and determine if

alarm is nuisance or real.

Initiating Alarm Alarm

(multiple alarms in an

interconnected system)

Green LED blinks once

per sec indicating that

this is the unit

initiating the alarm in

an interconnected,

multiple alarm, system.

Unit in Heat Alarm mode. During alarm, the initiating alarm

red blink will be interrupted by a

green blink.

3. Troubleshooting Guide

Trouble Condition Visual Indications Audible Indications Action:

Fault Mode/Fatal

Error

One AMBER

LED blink every 5

seconds.

Alarm chirps

every 30 seconds.

1. Push the Test/Hush button once to attempt to

reset the alarm.

The RED LED will blink out an Error Code

(number of blinks) when the Test/Hush button

is pushed/released once.Report the number of

blinks to Customer Service, if needed.

2. Clean your alarm. See “Cleaning Your Alarm”

for instructions.

3. Remove alarm from service. If fatal error

cannot be cleared, permanently discharge and

decommission the alarm.

Network Error

(if a alarm loses

wireless interconnect

connection due to

loss of signal)

One AMBER

LED blink every 5

seconds.

Alarm chirps every

30 seconds. (NOTE:

chirps only occur if

network includes more

than 2 alarms.)

Remove device from mounting bracket, and try

rotating and re-installing the device in a different

orientation on the mounting bracket. This might

align the antenna in a better position.

1. Push the Test/Hush button once to silence the

audible indication for 24 hours at a time.

The RED LED will blink out an Error Code

(number of blinks) when the Test/Hush button

is pushed/released once. Report the number of

blinks to Customer Service, if needed.

2. Follow instructions in “Resetting an Alarm’s

Wireless Interconnect Settings.”, then attempt

to rejoin the network by following the instruc-

tions in ”Adding Alarms to an Existing Wireless

Interconnected Network .”*If the error persists,

remove, discharge, and replace the alarm as

soon as possible.

Network Error due to

loss of radio

(CCI supervision)

One AMBER

LED blink every 5

seconds.

Alarm chirps every 30

seconds, regardless of

the number of

alarms in the network.

1. Push the Test/Hush button once to silence the

audible indication for 24 hours at a time.

The RED LED will blink out an Error Code (4

blinks) when the Test/Hush button is pushed/

released once. Report the number of blinks to

Customer Service, if needed.

2. Remove, discharge, and replace the alarm as

soon as possible.

Trouble Condition Visual Indications Audible Indications Action:

Low Battery One AMBER LED blink

every 5 seconds.

Alarm chirps every 60

seconds

Remove, discharge, then dispose of

alarm. Replace as soon as possible.

End of Alarm

Life (EOL)

One AMBER LED blink

every 5 seconds.

Double alarm chirp every

30 seconds.

The RED LED will blink out an Error

Code of 9 blinks. Start of EOL will be

delayed if Night Detect is active.

Hush (for Network

Error, End of Life)

One AMBER LED blink

every 5 seconds.

Chirp temporarily

silenced for 24 hours.

Push the Test/Hush button to

initiate Hush for 24hrs.

Alarm Fault: Number of RED LED Blinks (short

duration blinks) Wireless Fault: Number of RED LED Blinks (long duration

blinks)

7: Push to Test

8: Memory

9: Life Expiration

12: Temperature Sensor Supervision

2: Fault Coordinator

3: Fault RFD

4: CCI Supervision

5: RFD Check In

6: RFD Time Sync

4. Introduction, Product Features and Specifications

Introduction

The HDX-135Z-433 supervised heat alarm with freeze sensor is a self-diagnostic alarm with wireless

interconnection, 10-yr sealed battery and sensor life, built-in sounder, diagnostic/status LED,

integrated fixed temperature and rate-of-rise heat sensor and a pre-freeze condition indicator.

The HDX-135Z-433 uses a 918MHz transceiver for interconnection communication between

networked alarms. Up to 24 alarms can be a part of the same interconnected network.

The HDX-135Z-433 uses 10-year sealed-in lithium batteries ensuring continuous operation over the

10 year life of the alarm. This eliminates worry about battery removal or unauthorized deactivation of

the alarm. The self-activation feature activates the alarm when attached to the mounting bracket. At

the end of alarm life, the unit will chirp, indicating the alarm is in need of replacement (see

Troubleshooting Guide).

To help identify the date to replace the alarm, a label has been affixed to the side of the alarm. Write

the “Install date” in the space provided, and then write in the “Replace by” date (10 years from initial

power up) in permanent marker on the label prior to installing the alarm.

Power 3V DC non-replaceable sealed lithium batteries

Temperature sensor NTC Thermistor

Battery life 10 years*

Alarm life 10 years

Audible alarm

Heat

85dB at 10’ @ 3.0 to 3.5 KHz pulsing alarm

Temporal T3 pattern

Single Unit Box Dimensions 142mmx149mm x 65mm (W x L x H)

Product Dimensions Ø142.3 ± 0.3mm x 59.0 ± 1.0mm

Gross Weight (unit, pkg, etc) 452 grams

Net Product Weight 327 grams

Product Features and Specifications:

Tabla de contenidos

Otros manuales de Accesorios de Interlogix

Interlogix

Interlogix 60-886-95 Manual de usuario

Interlogix

Interlogix VE700AM Series Instrucciones de montaje

Interlogix

Interlogix RF-1012-07-5 Instrucciones de montaje

Interlogix

Interlogix SENTROL 1045T Series Manual de usuario

Interlogix

Interlogix TX-6010-03-1 Instrucciones de montaje

Interlogix

Interlogix TX-E611 Instrucciones de montaje

Interlogix

Interlogix DC115 Instrucciones de montaje

Interlogix

Interlogix ADC-IS-300-LP Manual de usuario

Interlogix

Interlogix AP750W Manual de usuario

Interlogix

Interlogix ShatterPro Instrucciones de montaje

Interlogix

Interlogix SDX-135Z-433 Manual de usuario

Interlogix

Interlogix 319.5 Manual de usuario

Interlogix

Interlogix RF-DC101 Series Instrucciones de montaje

Interlogix

Interlogix FlexPI Manual de instrucciones

Interlogix

Interlogix RCR-REX Manual de usuario

Interlogix

Interlogix International ShatterPro Instrucciones de montaje

Interlogix

Interlogix 868 GEN2 Instrucciones de montaje

Interlogix

Interlogix VE700 series Instrucciones de montaje

Interlogix

Interlogix HDX-135 Manual de usuario

Interlogix

Interlogix SDX-135Z Manual de usuario

Interlogix

Interlogix ShatterPro 60-873-95 Manual de usuario

Interlogix

Interlogix ShatterPro II Manual de usuario

Interlogix

Interlogix RF-1110-07-1 Instrucciones de montaje

Interlogix

Interlogix RF711I4 Instrucciones de montaje

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario