Intergraph InterServe 80 SL Manual de usuario

InterServe 80

Late-Breaking News

November 1998

DHA025360

and trademark law. This document may not, in whole or in part, be reproduced in any form or by any means, or be used to make any

derivative work, without written consent from Intergraph Computer Systems.

Use, duplication, or disclosure by the United States Government is subject to restrictions as set forth in subdivision (c)(1)(ii) of the

rights in technical data and computer software clause at DFARS 252.227-7013. Unpublished rights are reserved under the copyright

laws of the United States.

Intergraph Computer Systems, Huntsville AL 35894-0001

Notice

Information in this document is subject to change without notice and should not be considered a commitment by Intergraph Computer

Systems. Intergraph Computer Systems shall not be liable for technical or editorial errors in, or omissions from, this document.

Intergraph Computer Systems shall not be liable for incidental or consequential damages resulting from the furnishing or use of this

document.

All warranties given by Intergraph Computer Systems about equipment or software are set forth in your purchase contract. Nothing

stated in, or implied by, this document or its contents shall be considered or deemed a modification or amendment of such

warrantites.

Trademarks

Intergraph Computer Systems and the Intergraph Computer Systems logo are registered trademarks of Intergraph Computer Systems.

InterServe, InterRAID, and TowerMate are trademarks of Intergraph Computer Systems.

Other brands and product names are trademarks of their respective owners.

General

System Graphics

The System Reference refers to specific graphics cards. However, your system may have been

delivered with graphics not referred to in the System Reference. See the separate graphics

documentation delivered with the system for information on your system’s graphics.

Three-Button Primax Mouse

If your system was delivered with a three-button Primax mouse, you may see a message that

says “MouseWare has detected a new Wheel Mouse....” and asks if you want to configure the

new device. If this happens, select No. If you experience any other anomalies while using the

Primax mouse, reinstall the mouse driver found on the Windows NT software CD-ROM.

Logitech Wheel Mouse

If your system was delivered with a Logitech wheel mouse, you can find information on using

it by right-clicking the mouse icon in the taskbar tray, or by going to Start/Settings/Control

Panel/Mouse and clicking Help in the toolbar.

If the wheel on the mouse does not function, or if you experience any other anomalies while

using the wheel mouse, install theLMOUSE driver software from the Intergraph System CD

using InterSite Version Manager.

Disk Activity LED and PCI Disk Controllers

The disk activity LED only shows activity for disk drives cabled to the system board (that is,

SCSI drives using the on-board SCSI controller). The LED does not indicate disk activity for

disk drives attached to a PCI adapter (such as an add-on disk controller).

Internal and External RAID Configurations

The basic RAID configuration for an InterServe 80 consists of a RAID controller cabled to

disk drives internal to the system. You can add external RAID cabinets by adding additional

RAID controllers and cabling the cabinets to these additional controllers. You cannot connect

an external RAID cabinet to the RAID controller cabled to the system's internal disk drives.

MegaRAID Controller and Software Information

For information on the AMI MegaRAID controller installed in an InterServe 80 with internal

RAID, and for information on the MegaRAID software, refer to the InterRAID-8e

documentation delivered with the system.

On a server with an InterRAID disk array, you should install the MegaRAID Power Console

software. You should also add a shortcut to Power Console to the Windows NT Startup menu

(Start/Programs/Startup). Power Console provides valuable information about the health of

the RAID disk array, and can help you pinpoint any problems that may occur in disk array

operation. Power Console can even help predict disk array problems before they occur,

allowing you to take action before problems become critical.

Power Console installation is described in the System Setup document delivered with the

system. Power Console is described in the InterRAID documentation delivered with the

system. See Windows NT Help for information on adding a shortcut to the Start menu.

Enabling the MegaRAID Audible Alarm

On an InterServe 80 with an AMI MegaRAID disk controller, the controller’s audible alarm is

disabled by default. You can configure the InterSite Watchdog program to alert you to RAID

problems such as disk failures. If you want to enable the controller’s audible alarm, you can

do so using the MegaRAID BIOS Configuration Utility or Power Console. For more

information, see Watchdog Help and the InterRAID documentation delivered with the system.

Operating System Support for USB Peripherals

Your system includes Universal Serial Bus (USB) ports to which you can connect USB

peripherals. Windows NT 4.0 does not currently support USB peripherals. Microsoft will

add support for USB peripherals to a future Windows NT release.

System BIOS

Please note the following items related to the system’s BIOS:

An incorrect BIOS version for the system may be listed in the System Setup document.

The correct BIOS version is 887xx.

The troubleshooting information in the System Setup document contains a list of beep

codes and error messages. These beep codes are not used by the current InterServe 80

system board. If your system powers on but does not display any video, check for proper

installation of the memory modules and the video display adapter.

The BIOS Setup options Floppy Access Control and IDE Hard Disk Access Control (used

to write-protect these devices) have no effect under Windows NT. Windows NT does not

use the BIOS for peripheral device access.

Immediately after installing a Symbios SCSI adapter card, you must run the Symbios

SCSI Configuration Utility (PCI_CFG.EXE) to disable SCAM on the SCSI adapter card,

and to change the Adapter Boot Order to include the SCSI adapter card. The correct boot

order is as follows:

Boot Order Bus / Device Description

0 0 / 60 Internal SCSI channel

1 0 / 61 External SCSI channel

2 Varies / Varies Symbios SCSI adapter card

The bus and device numbers for the card depend on the slot in which the card is installed.

Your System Setup document may not have information on BIOS power management options.

Select Power Management in the BIOS Setup main menu to display these options.

Option Notes

Power Management/APM Set this option to Enabled to enable the chipset power

management and APM features. The settings are Enabled or

Disabled. The Fail-Safe and Optimal settings are Disabled.

CAUTION Do not enable this parameter unless you fully

understand the function of each of the following

parameters.

Green PC Monitor Power

State This option specifies the power state that the green PC-

compliant video monitor enters when the BIOS places it in a

power saving state after the specified period of display

inactivity has expired. The settings are Off, Standby, Suspend,

or Disabled. The Optimal and Fail-Safe settings are Standby.

Video Power Down Mode This option specifies the power state that the video subsystem

enters when the BIOS places it in a power saving state after the

specified period of display inactivity has expired. The settings

are Standby, Suspend or Disabled. The Optimal and Fail-Safe

settings are Disabled.

Hard Disk Power Down

Mode This option specifies the power conserving state that the hard

disk drive enters after the specified period of hard drive

inactivity has expired. The settings are Disabled, Standby, or

Suspend. The Optimal and Fail-Safe settings are Disabled.

Hard Disk Time Out This option specifies the length of a period of hard disk drive

inactivity. When this length of time expires, the system enters

power-conserving state specified in the Hard Disk Power Down

Mode option. The settings are Disabled, 1 min. (minute), 2

Option Notes

min, 3 min., 4 min., 5 min., 6 min, 7 min., 8 min., 9 min., 10

min., 11 min., 12 min., 13 min., 14 min, and 15 min. The

Optimal and Fail-Safe settings are Disabled.

Standby Time Out This option specifies the length of a period of system inactivity

while in the Full On power state. When this length of time

expires, the system enters the Standby power state. The settings

are Disabled, 4 msec, 8 msec, 12 msec, 16 msec, up to 508

msec, in increments of 4 msec. The Optimal and Fail-Safe

settings are Disabled.

Suspend Time Out This option specifies the length of a period of system inactivity

while in the Standby power state. When this length of time

expires, the system enters the Suspend power state. The

settings are Disabled, 4 msec, 8 msec, 12 msec, 16 msec, up to

508 msec, in increments of 4 msec. The Optimal and Fail-Safe

settings are Disabled.

Disk Drive Delayed Start

Hard disk drives draw an extra amount of power when the system is first powered on. The

power supply can support up to two hard disk drives powering on (spinning up) at once. If

you use more than two hard disk drives in a system, you must activate the delayed start feature

on the additional hard disk drives. Doing this forces these drives to pause before spinning up,

allowing the power supply to finish starting the first drives. See the disk drive documentation

or the disk drive label for information on activating delayed start.

333 MHz Processor in an InterServe 80

An InterServe 80 must be running BIOS version 8870F or higher to support a 333 MHz

Pentium II processor. The system board jumper settings for a 333 MHz Pentium II processor

are as follows:

J21 J27 J28 J31

Out Out In In

IN denotes the jumper is installed on both pins. See the System Reference document for

detailed information on system board jumper locations and settings.

Document Errata

In the System Setup document:

In Chapter 2, “Setting Up the Software,” the location of the online System Introduction

document may be incorrect. The correct location is C:\WIN32APP\SYSINTRO.

In Chapter 4, “Operating Notes,” the locations of the system’s serial number and model

number have changed. Both are on a label under the the top cover at the front of the

chassis. The serial number is also found on a bar-code label on the back panel.

In the System Reference document, references to Chassis Fan 1 and Chassis Fan 2 (and their

system board connectors) are reversed. Chassis Fan 1 is the bottom front fan; Chassis Fan 2 is

the top rear fan. The system board connector for Chassis Fan 1 is J54; the system board

connector for Chassis Fan 2 is J5.

Windows NT 4.0

Installing Mass Storage Drivers During Setup

The System Setup document delivered with the system contains instructions for reinstalling the

operating system if needed. The instructions for what to do during installation of the

operating system direct you to bypass automatic detection of mass storage devices during

Setup. This is incorrect; instead of bypassing automatic detection, you should do the

following:

When prompted during Setup, select automatic detection of mass storage devices.

After completing Setup, reinstall the driver for the SCSI controller (SYMSCSIDRV) from

backup diskette.

For instructions on creating backup diskettes containing system software, see the System Setup

document and InterSite Version Manager Help. For instructions on installing a driver from

diskette, see the README.TXT file on the backup diskette containing the driver software.

Installing the Adaptec SCSI Controller Driver

If you have to reinstall Windows NT 4.0 on a system with an optional Adaptec SCSI

controller, be sure to reinstall the driver for the SCSI controller (2940SCSIDRV) from backup

diskette during Setup.

To install the 2940SCSIDRV driver during Setup:

1. When prompted, press Sto bypass detection of mass storage devices.

2. When prompted, press Sto specify a mass storage device other than those listed.

3. When prompted, select Other from the list of devices presented.

4. Follow the prompts to install the driver from the 2940SCSIDRV backup diskette. When

presented with a list of Adaptec SCSI controllers, select the entry for Windows NT 4.0.

Installing the InterCON-X RS-232 Adapter Driver

If you install an InterCON-X RS-232 adapter in your InterServe 80, be sure to install the

driver software for this adapter from the Microsoft Windows NT Server software CD-ROM.

Installing QFE Software

Quick-Fix Engineering (QFE) update software contains fixes for operating system problems or

limitations. If a system requires Quick-Fix Engineering (QFE) update software, it is installed

on the system before it leaves the factory. If QFE update software is installed on the system, a

QFE backup diskette is delivered with the system. You can also create a QFE backup diskette

using InterSite Version Manager.

If you reinstall the Windows NT 4.0 operating system, and the Windows NT 4.0 Service Pack

3 software, be sure to reinstall the QFE update software as well. Install the QFE update

software after you reinstall Service Pack 3 software. QFE update software contains post-

Service Pack 3 fixes.

Otros manuales para InterServe 80 SL

Tabla de contenidos

Otros manuales de Servidor de Intergraph

Intergraph

Intergraph InterServe 9400 Manual de usuario

Intergraph

Intergraph InterServe 8000 Guía del usuario

Intergraph

Intergraph InterServe 800 SL Manual de usuario

Intergraph

Intergraph InterServe 9000 Guía del usuario

Intergraph

Intergraph TD-x10 Setup Manual de usuario

Intergraph

Intergraph InterServe 800 SL Manual de usuario

Intergraph

Intergraph InterServe 80 SL Manual de usuario

Intergraph

Intergraph InterServe 80 SL Manual de usuario

Intergraph

Intergraph InterServe 800 SL Guía del usuario

Intergraph

Intergraph InterServe 8000 Guía del usuario

Intergraph

Intergraph InterServe 9400 Manual de usuario

Intergraph

Intergraph Zx10 Ultra-Tower Manual de lista de piezas

Intergraph

Intergraph InterServe 90 Guía del usuario

Intergraph

Intergraph InterServe 80 SL Guía del usuario

Intergraph

Intergraph InterServe 600 Series Guía del usuario

Intergraph

Intergraph Zx10 5U Manual de lista de piezas

Intergraph

Intergraph InterServe 800 SL Manual de usuario

Intergraph

Intergraph InterServe 800 SL Manual de usuario

Intergraph

Intergraph InterServe 800 SL Guía del usuario

Intergraph

Intergraph InterServe 80 SL Manual de usuario

Intergraph

Intergraph InterServe 650 ?anual Guía del usuario

Intergraph

Intergraph InterServe WebScale Manual de usuario

Intergraph

Intergraph InterServe 600 Series Manual de usuario

Intergraph

Intergraph InterServe 80 SL Guía del usuario

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario