Intellinet 505932 Manual de usuario

HI-SPEED USB 2.0

GIGABIT ETHERNET

ADAPTER

USER MANUAL

MODEL 505932

INT-505932-UM-0511-04

FCC Certifications

This Equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio

communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received; including interference that may cause undesired operation.

CE Warning

This equipment complies with the requirements relating to electromagnetic compatibility, EN

55022 class B for ITE, the essential protection requirement of Council Directive 2004/108/EC on

the approximation of the laws of the Member States relating to electromagnetic compatibility.

Company has an on-going policy of upgrading its products and it may be possible that information

in this document is not up-to-date. Please check with your local distributors for the latest

information. No part of this document can be copied or reproduced in any form without written

consent from the company.

Trademarks:

All trade names and trademarks are the properties of their respective companies.

1. Unpacking Information

Thank you for purchasing the USB to Gigabit Ethernet adapter. Before you start, please

verify that your package contains the following items:

1. One USB to Gigabit Ethernet Adapter.

2. One driver & manual CD

2. Overview

2.1 Introduction

This USB to Gigabit Ethernet adapter is a cost-effective solution that converts a USB

port into a 10/100/1000 Base-T Ethernet port. It enables a low-cost and affordable

Gigabit Ethernet network connection to desktop and notebook PCs and embedded

systemsusing popular USB ports: no need to purchase an expensive Gigabit network

interface card or use a PCI or Card bus slot — just plug into an available USB port on a

desktop or laptop PC running Windows 7/2003/XP/Vista or Linux/Mac.

Installation and operation are further simplified by living up to USB's Plug and Play

installation approach to connecting computer peripherals. You will not need to open the

case of your computer, nor will you be required to set IRQs. It also supports full and half

duplex mode to achieve the best speeds for each attached device, and hot-swap

capability provides the simplest way to connect your computer to an Ethernet-based

network.

2.2 Key Features

Complies with IEEE 802.3 10BASE-T standard

Complies with IEEE 802.3u 100BASE-TX standard

Complies with IEEE 802.3ab 1000BASE-T standard

Compliant with USB 1.1 and 2.0 standards

Complies with IEEE 802.3x Flow Control

Supportsfull/half duplex operation

Plug and Play Installation

Support hot inserting and swapping

Automatically negotiates 10/100/1000 Mbps connection rate

Support drivers for Windows 7/2003/XP/ Vista/Linux/Mac

FCC, CE Class B

2.3 LED Definition

Power

Green: Power is on

Off: Power is off

10/100M Link/ACT

Green: Valid link on this port

Blinking: Data transferring/ receiving on this port

Off: No Valid Link on this port or the port is connected at 1000 Mbps

1000M Link/ACT

Green: Valid link on this port

Blinking: Data transferring/ receiving on this port

Off: No Valid Link on this port or the port is connected at 10/100 Mbps

3. Installing the USB to Gigabit Ethernet Adapter

3.1 System Requirements

Pentium 166 MMX or above processor-based PC

Available USB port

Microsoft Windows 7/2003/XP/Vista or Linux or Mac

CD-ROM Drive

3.2 Hardware Installation

Before installation, check if there is an available active USB port. To check this, go

to My Computer > Control Panel > System, then click the Device Manager tab to

check if the Universal Serial Bus controller is displayed, as shown below.

3.2.1 Connect the Adapter to your PC

1. Plug the USB adapter into your PC.

2. Windows will detect the new hardware automatically and prompt you for the

driver. For driver installation, refer to the chapter “Software Installation.”

3.3 Software Installation

After attaching the USB to Gigabit Ethernet adapter to your PC or laptop, the

auto-detection for new hardware will be activated automatically. The procedures to

perform driver installation differ slightly from each operation system: Refer to the

following sections.

3.3.1Windows XP Setup

1. Select “Install from a list or specific location,” then click next.

2. Insert the provided driver CD. Select “Include this location in the search,” then click

“Browse.”

3. Choose the location of your CD-ROM. Locate the setup.exe file in the folder

“D:505932_USB_ Gigabit_Ethernet_Adapter\WinXP,” where “D” is the designation

of your CD drive. Click “Next” to proceed.

4. A caution window may pop up. Click ”Continue Anyway.” There won’t be any effect

on the performance of the adapter.

5. Click “Finish”to complete the installation and activate the adapter.

3.3.2Windows Vista setup

1. When the Found New Hardware box appears, close this window.

2. Go to Start Control Panel Hardware and Sound Device Manager.

3. Double-click the “AX178” icon.

Otros manuales para 505932

Tabla de contenidos

Otros manuales de Adaptador de Intellinet

Intellinet

Intellinet 524766 Manual de usuario

Intellinet

Intellinet 503273 Manual de usuario

Intellinet

Intellinet ISTREAM HD 525282 Manual de usuario

Intellinet

Intellinet iStream HD Manual de usuario

Intellinet

Intellinet 530361 Manual de usuario

Intellinet

Intellinet PowerLine Turbo Ethernet Adapter Manual de usuario

Intellinet

Intellinet 525152 Manual de usuario

Intellinet

Intellinet IPI-15 Manual de usuario

Intellinet

Intellinet 525336 Manual de usuario

Intellinet

Intellinet 503273 Manual de usuario

Intellinet

Intellinet 503457 Manual de usuario

Intellinet

Intellinet 503273 Manual de usuario

Intellinet

Intellinet PowerLine HD Ethernet Adapter 503839 Manual de usuario

Intellinet

Intellinet 524995 Manual de usuario

Intellinet

Intellinet 524773 Manual de usuario

Intellinet

Intellinet 503457 Manual de usuario

Intellinet

Intellinet 501262 Manual de usuario

Intellinet

Intellinet 525275 Manual de usuario

Intellinet

Intellinet 525206 Manual de usuario

Intellinet

Intellinet 502641 Manual de usuario

Intellinet

Intellinet 524698 Manual de usuario

Intellinet

Intellinet 523974 Manual de usuario

Intellinet

Intellinet 522496 Manual de usuario

Intellinet

Intellinet 561495 Manual de usuario

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario