Intelbras VP 5311 MW Pet Manual de usuario

User manual

IVP 5311 MW Pet

English

IVP 5311 MW Pet

Passive infrared sensor

Congratulations, you have just purchased a product with Intelbras quality and safety.

The IVP 5311 MW Pet passive infrared sensor has passive infrared and microwave detection technology, adopting advanced

signal analysis technology, which can prevent false triggering in dangerous environments. This sensor is intended for indoor

and semi-open environments.

Care and safety

» LGPD – Data processing by Intelbras: Intelbras does not access, transfer, capture or perform any type of processing of

personal data from this product.

» Follow all instructions in the manual for assembling and installing the product;

» Fix the sensor on stable surfaces, where there are no vibrations;

» This sensor is intended for closed and semi-open environments;

Semiaberto Fechado Externo

Semi-open Closed External

» Do not use the sensor in areas with sudden changes in temperature, such as near air conditioners and heaters, fans,

refrigerators and ovens. Do not expose the sensor to direct or reected sunlight;

» Do not install the sensor facing windows and glass doors;

» Do not touch the surface of the infrared (PIR) sensor. If necessary, use a cleaning cloth;

» The recommended maximum installation height is 2.20 m, do not exceed it;

» Do not place objects in front of the sensor. To ensure the detection area, avoid curtains, screens, screens, or any object

that may interfere with its coverage area;

» For the use of the articulator, we recommend that the installation be carried out by a professional installer, as its incorrect

use could impair the Pet function and the sensor coverage angle;

» The sensor must be installed where a possible intruder can be easily detected, that is, where it makes transverse move-

ments to the detection beams (see the gure below);

» The

Pet

function is intended for crawling animals weighing up to 20 kg. If the animal is on top of a bench, for example,

the

Pet

function can be canceled.

Note: before starting the installation, it is necessary to dene the height at which the sensor will be positioned, which can

vary from 1.8 to 2.2 m. If the sensor is installed at a height of less than 1.8 m or is tilted downwards, the Pet function will be

compromised.

Scan

8 (m)

0 2 4 6 8

12 (m)

Upper view

Detection range

1.2 4 6 8 10 12m

1.8 ~2.20m

1,8 ~ 2,20 m

Side view

Summary

1. Technical specications 6

2. Features 6

3. Product 7

4. Installation 7

4.1. Microwave sensitivity adjustment ...............................................................9

4.2. Operating mode settings ....................................................................10

4.3. Jumper J. LED ..................................................................................... 11

4.4. Jumper J. Pulso ...............................................................................11

4.5. Jumper SENS ....................................................................................11

4.6. Jumper Relé..............................................................................11

4.7. Jumper Mode.............................................................................12

4.8. Completion of the process ...................................................................12

5. Operation 13

6. Test 13

7. Homologation 14

Warranty term 15

1. Technical specications

Operating voltage 9 ~16 Vdc

Operating current 38 mA

Detection angle 90°

Detection range (PIR and MW) 12 meters

Detection method Microwave and PIR (AND)

Animal immunity Up to 20 kg

Microwave frequency 10.525 GHz

Sensitivity (J. Pulse)

1- High sensitivity

2- Sensitivity (factory default)

3- Medium sensitivity

4- Low sensitivity

Sensitivity (J. SENS)

1- High sensitivity

2- Medium sensitivity

3- Sensitivity (factory default)

4- Low sensitivity

5- Minimum sensitivity

Anti-violation front tamper

Indicator LEDs

Yellow (PIR)

Red (MW)

Blue (Alarm)

Maximum startup time 80 seconds

Relay opening time 3 seconds

Recommended installation height 2.1 meters

Operating Temperature -10 °C ~ +50 °C

Relay output NA /NF

Dimensions (W × H × D) 55 × 140 × 60 mm

2. Features

» Microcontrolled sensor.

» Anti-camouage technology.

» Microwave sensitivity adjustment.

» PIR pulse and sensitivity adjustment.

» Automatic real-time temperature compensation.

» Immunity to white light up to 20,000 lux.

» High immunity to RFI/EMI.

» Highly effective algorithm against false triggering.

» Pet immunity up to 20 kg.

» Tamper key for lower front cover.

» Quick connect connector.

» Ease of installation.

3. Product

1P 2P 3P 4P

LD1

LD2

LD3

TAMPER ALARME

RELÉ

MODO

SENS.

J. LEDS

16 17 18

1. Top front cover

2. Fresnel lens

3. Lower front cover

4. Hole for xing the bottom cover

5. Basis

6. Oblong for wall mounting

7. Holes for mounting bracket

8. Lacquer for wall installation

9. Seals for corner installation

10. Lacquer for cable passage

11. Microwave module

12. Jumper SENS

13. MODE jumper (AND and anti-stealth

14. Jumper Relay (NO / NC)

15. Tamper switch

16. Jumper WRIST

17. Connection terminals

18. Microwave adjustment trimpot

19. LEDs

20. Piro senor

21. Jumper J. LEDs

22. LED setting microwave

4.Installation

» Before starting the installation, it is necessary to dene the height at which the sensor will be positioned, which can vary

from 1.8 to 2.2 m;

» Do not install sensors that have microwave technology close to each other, as there may be interference between them;

18m

1.8 a 2.2m

» Microwave sensitivity adjustment should be done according to each environment;

» For installation using the articulator, make sure that both the sensor and the support are well xed at the installation site

to avoid changes in the product’s detection angle. Incorrect use of the articulator can alter the sensor’s detection area,

creating blind spots and impairing operating efciency;

» If the sensor is installed at an angle, its detection range and

Pet

function may be impaired in such a way as to cancel

the function.

To install the sensor, follow the procedure below:

1. Remove the lower front cover;

1P 2P 3P 4P TAMPER ALARME

2. Route the wiring through the cable knockouts located on the back cover of the sensor.

Note: use a tool to drill the hole in the indicated location and to facilitate the installation, use the recesses in the rear cover

to pass the cables.

1P 2P 3P 4P TAMPER ALARME 1P 2P 3P 4P TAMPER ALARME

Passagem de

cabo

Passage of

cables

3. Connect the connecting cables to the sensor terminals and install them in the place to be protected. For installation

directly on the wall or on the edge of the wall, break the sealing waxes indicated for the furos on the rear xing cover.

Note: for installation directly on the wall, use the oblong located on the back of the product. Use a parafuso with dimen-

sions 6×20 mm, executing the procedure to follow. Fix the cover 1 on the wall and t the oblong so that the sensor is rm.

Using the hole below two connectors, place the cover 2 for total xation of the sensor.

Oblongo

Parafuso 1

Encaixe a cabeça do parafuso

na cavidade do oblongo

Lacre

Parafuso 2

Montado na parede Montado no canto da parede

1P 2P 3P 4P TAMPER ALARME

Wall mounted Wall mounted corner

Screw 1

Screw 2 Sealing

Sealing Sealing

Coloque la cabeza del

tornillo en el oricio del

oblongo

4. Make the settings on the sensor following the directions.

4.1. Microwave sensitivity adjustment

The trimpot allows you to adjust the sensitivity of the microwave. Turning the trimpot in a non-clockwise direction

increases the sensitivity and consequently the distance that the microwave is capable of detecting movements. Rotating

counterclockwise or microwave is less sensitive.

Note:

it is highly recommended to adjust the sensitivity of the microwaves so that the detection occurs only in the

environment where the sensor is installed.This technology is capable of detecting movements through a wall, for example.

≅1M

25%

≅5M

50%

≅12M

75%

≅15M

100%

≅18M

12m

Área que se quer proteger

In gure 1 of the example above we have the area that we want to protect. Figures 5 and 6 indicate that the adjustment

of the trimpot exceeds the limits of the environment to be protected. In this way, the microwave will detect movements on

the external side of the desired area.

To facilitate the adjustment of the microwave coverage, adjust the trimpot in an anti-clockwise direction (less sensitive) and

walk in the environment that you want to protect. Observe the motion detection of the sensor. If necessary, increase the

sensitivity (clockwise). Repeat this process until the sensor protects only the environment where it is installed.

The gure below shows a reference range of detection of the microwave channel.

Microwave reach

Trimpot position Maximum distance (meters)

25%

50%

75%

100%

0% - up to 1 metro

25% - up to 5 metros

50% - up to 12 metros

75% - up to 15 metros

100% - up to 18 metros

1P 2P 3P 4P TAMPER ALARME

Factory default: 50%

Microwave Adjustment LED The Microwave Adjustment LED is a way to signal microwave detection. Therefore, when

performing the sensitivity adjustment, walk across the entire area you want to protect, observing if the LED will light up.

4.2. Operating mode settings

Note: to perform the Mode, Relay and LED sensitivity adjustments, it is necessary to open the front cover of the sensor,

as shown in the following gures.

Insert a screwdriver into the side of the top slot on the cover, then push the cover forward.

1P 2P 3P 4P

LD1

LD2

LD3

TAMPER ALARME

RELÉ

MODO

SENS.

J. LEDS

RELÉ

MODO

SENS.

J. LEDS

1P 2P 3P 4P

J. PULSO

Tabla de contenidos

Otros manuales de Sensor de seguridad de Intelbras

Intelbras

Intelbras XAS 8000 Manual de usuario

Intelbras

Intelbras IVP 4101 PET Manual de usuario

Intelbras

Intelbras IVP 1000 PET Manual de usuario

Intelbras

Intelbras IVP 8000 EX Manual de usuario

Intelbras

Intelbras IVP 1000 PET Manual de usuario

Intelbras

Intelbras IVP 2000 SF Manual de usuario

Intelbras

Intelbras IVP 4101 PET Manual de usuario

Intelbras

Intelbras IVP 3000 PET Manual de usuario

Intelbras

Intelbras IVP 8000 EX Manual de usuario

Manuales populares de Sensor de seguridad de otras marcas

THORLABS

THORLABS PDA10JT Manual de usuario

Waeco

Waeco UV-DETECT Manual de usuario

Intermatic

Intermatic IOS-DSIMF Manual de usuario

urmet domus

urmet domus 1083 Manual de usuario

Siemens

Siemens AZL66 Series Manual de usuario

BTI

BTI Profiline Multi Finder Manual de usuario

Challenger

Challenger SL01 Manual de usuario

DMP Electronics

DMP Electronics 1122INT Manual de usuario

Rielta

Rielta Ladoga MK-RK Manual de usuario

Mirion Technologies

Mirion Technologies ACCURAD PRD Manual de usuario

Bosch

Bosch DS835 Manual de usuario

DBI SALA

DBI SALA EZ Stop Manual del operador

Lamptime

Lamptime ST05C Manual de usuario

Ubiquiti

Ubiquiti MFI-MSC Manual de usuario

Subsite

Subsite 910R Instrucciones de instalación

Satel

Satel OPAL Pro Manual de usuario

Aleph

Aleph XC-1XTEU Manual de usuario

Pima

Pima LARIS QUAD Manual de usuario