Intel Vectra VEi7 Manual de usuario
Intel EtherExpress PRO 100B-TX
PCI Ethernet Adapter
Installation Guide
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose.
Hewlett-Packard shall not be liable for errors contained herein or for incidental
or consequential damages in connection with the furnishing, performance, or use
of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its
software on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated to another language without the prior written consent
of Hewlett-Packard Company.
Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft
Corporation.
MMXTM is a trademark of Intel Corporation.
Pentium® is a registered trademark of Intel Corporation.
Hewlett-Packard France
Commercial Desktop Computing Division
38053 Grenoble Cedex 9
France
©1999 Hewlett Packard Company
General information to read before installing
General information to read before installing
On all systems: before installing LAN card, go into Bios setup and set PnP OS field to NO.
• How to change LAN card configuration if needed (Advanced users only)
This is a general advisory on how to forcibly modify resources for ISA and PCI network
cards.
ISA cards:
• For ISA network adapters, start the configuration tool provided in driver
kit (See install documentation)
• Under CMOS setup, go to Advanced > PnP/PCI ISA IRQ Resource Exclu-
sion > reserve an IRQ for the adapter.
PCI cards:
• For PCI network adapters, go to CMOS setup > Advanced > PnP/PCI ISA
IRQ Resource Exclusion > reserve the IRQ for Legacy ISA.
• ISA cards can’t use IRQ9
• IRQ 9 is reported as being used by ACPI during POST. This is due to ISA’s
inability to share IRQs.
• Using a different IRQ (e.g. 5, 7, 10, and 11) will work. For this:
1Install the NIC then power up the system.
2Press F2 to go to CMOS setup.
3Set PnP OS to NO and reserve IRQ 5, 7, 10, or 11 (explained in installation
section)
4Save the configuration settings and boot to the applicable OS.
5Follow installation steps.
Sound conflict under Win 95 on VLi8 only
• On VLi8, LAN cards cause an IRQ conflict with the embedded sound de-
vice under Win95.
• To solve the problem: Reserve IRQ 5 and sett PNP OS to no. For this:
1Install the NIC then power up the system.
General information to read before installing
2Press F2 to go to CMOS setup.
3Set PNP OS to NO and reserve IRQ 5.
4Save settings and boot to applicable OS.
1 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Microsoft Windows 95 SR2.5
1 Installing the Intel EtherExpress PRO 100B-TX PCI
Ethernet Adapter
Microsoft Windows 95
SR2.5
Connecting to a
Windows NT 3.51 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Intel EtherExpress PRO 100B-TX PCI Ethernet adapter and driver disk
version 2.51.
• Driver File: E100B.SYS, version 2.24
• Microsoft Windows 95 SR2.5 media.
• Microsoft Windows NT 3.51 Server system that supports NetBEUI,
NWLink IPX/SPX Compatible Transport, and NWLink NetBIOS network
protocols.
Device Configuration
Procedure
1With the HP Vectra turned off, install the Intel EtherExpress PRO 100 PCI
adapter card into a PCI slot.
2Connect network cable media to the Intel EtherExpress PRO 100 card.
3Power on the machine and start the system in MS-DOS mode.
4Insert the EtherExpress PRO 100 driver disk, “PRO/100B LAN Adapter
Configuration and Driver Diskette” and execute “SETUP.EXE”.
5Select “View Adapter Configuration” and verify the resource settings
listed above under the heading “View Adapter Configuration”.
6Save any required changes and exit.
7Remove the Intel driver diskette from the floppy drive and restart the
system.
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 10 03 10
I/O Address 1020 DCE0 E400
1 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Connecting to a Windows NT 3.51 Server
8Windows 95SR2.5 will automatically recognize the Intel ethernet card as
“PCI Ethernet Controller”.
9Insert the “PRO/100B LAN Adapter Configuration and Driver Diskette” in
the floppy drive and click on “Next” from the Update Device Driver Wizard
dialog box.
10 When Windows 95 detects the updated driver, “Intel 82557C-based
Ethernet PCI (10/100)”, click on “Finish”.
11 Insert the Windows 95 CDROM when prompted. The system will copy all
the necessary files to complete the installation.
12 Click on “OK” when the system prompts for the computer and workgroup
names.
13 Enter the Computer Name, Workgroup, and Computer Description in the
appropriate spaces and click on “Close” (Contact your network
administrator if you do not have the required information).
14 Remove the Intel diskette from the floppy drive and click on “YES” to
restart the system when prompted.
15 Right-click on the “Network Neighborhood” icon and select “Properties”.
16 Accept the default Network Protocols and the Primary Network Logon
(Client for Microsoft Networks) as seen below and click on “OK”. (If you
do not have the required information, contact your network
administrator)
17 Client for Microsoft Network
Client for Microsoft Networks
Intel 82557C-based Ethernet PCI (10/100)
IPX/SPX-compatible Protocol
NetBEUI
18 Click on “OK” to accept the configuration.
19 Specify the path to your Windows 95 files when prompted.
2 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Microsoft Windows 95 SR2.5
2 Installing the Intel EtherExpress PRO 100B-TX PCI
Ethernet Adapter
Microsoft Windows 95
SR2.5
Connecting to a
Windows NT 4.0 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Intel EtherExpress PRO 100B-TX PCI Ethernet adapter and driver disk
version 2.51.
• Driver File: E100B.SYS, version 2.24
• Microsoft Windows 95 SR2.5 media.
• Microsoft Windows NT 4.0 Server system that supports NetBEUI, NWLink
IPX/SPX Compatible Transport, and NWLink NetBIOS network protocols.
Device Configuration
Procedure
1With the HP Vectra turned off, install the Intel EtherExpress PRO 100 PCI
adapter card into a PCI slot.
2Connect network cable media to the Intel EtherExpress PRO 100 card.
3Power on the machine and start the system in MS-DOS mode.
4Insert the EtherExpress PRO 100 driver disk, “PRO/100B LAN Adapter
Configuration and Driver Diskette” and execute “SETUP.EXE”.
5Select “View Adapter Configuration” and verify the resource settings
listed above under the heading “View Adapter Configuration”.
6Save any required changes and exit.
7Remove the Intel driver diskette from the floppy drive and restart the
system.
8Windows 95SR2.5 will automatically recognize the Intel ethernet card as
“PCI Ethernet Controller”.
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 10 03 10
I/O Address 1020 DCE0 E400
2 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Connecting to a Windows NT 4.0 Server
9Insert the “PRO/100B LAN Adapter Configuration and Driver Diskette” in
the floppy drive and click on “Next” from the Update Device Driver Wizard
dialog box.
10 When Windows 95 detects the updated driver, “Intel 82557C-based
Ethernet PCI (10/100)”, click on “Finish”.
11 Insert the Windows 95 CDROM when prompted. The system will copy all
the necessary files to complete the installation.
12 Click on “OK” when the system prompts for the computer and workgroup
names.
13 Enter the Computer Name, Workgroup, and Computer Description in the
appropriate spaces and click on “Close” (Contact your network
administrator if you do not have the required information).
14 Remove the Intel diskette from the floppy drive and click on “YES” to
restart the system when prompted.
15 Right-click on the “Network Neighborhood” icon and select “Properties”.
16 Accept the default Network Protocols and the Primary Network Logon
(Client for Microsoft Networks) as seen below and click on “OK”. (If you
do not have the required information, contact your network
administrator)
17 Client for Microsoft Networks
Client for Microsoft Networks
Intel 82557C-based Ethernet PCI (10/100)
IPX/SPX-compatible Protocol
NetBEUI
18 Click on “OK” to accept the configuration.
19 Specify the path to your Windows 95 files when prompted.
3 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Microsoft Windows 95 SR2.5
3 Installing the Intel EtherExpress PRO 100B-TX PCI
Ethernet Adapter
Microsoft Windows 95
SR2.5
Connecting to a Novell
NetWare 3.12 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Intel EtherExpress PRO 100B-TX PCI Ethernet adapter and driver disk
version 2.51.
• Driver File: E100B.SYS, version 2.24
• Microsoft Windows 95 SR2.5 media.
• Novell NetWare 3.12 Server system that supports IPX network protocol.
• Novell Client for Windows 95 v2.5 installation media.
Device Configuration
Procedure
1With the HP Vectra turned off, install the Intel EtherExpress PRO 100 PCI
adapter card into a PCI slot.
2Connect network cable media to the Intel EtherExpress PRO 100 card.
3Power on the machine and boot to Windows 95 SR2.5.
4Windows 95SR2.5 will automatically recognize the Intel ethernet card as
“PCI Ethernet Controller”.
5Insert the “PRO/100B LAN Adapter Configuration and Driver Diskette” in
the floppy drive and click on “Next” from the Update Device Driver Wizard
dialog box.
6When Windows 95 detects the updated driver, “Intel 82557C-based
Ethernet PCI (10/100)”, click on “Finish”.
7Insert the Windows 95 CDROM when prompted. The system will copy all
the necessary files to complete the installation.
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 10 03 11
I/O Address 1020 DCE0 E400
3 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter
Connecting to a Novell NetWare 3.12 Server
8Click on “OK” when the system prompts for the computer and workgroup
names.
9Enter the Computer Name, Workgroup, and Computer Description in the
appropriate spaces and click on “Close” (Contact your network
administrator if you do not have the required information).
10 Remove the Intel diskette from the floppy drive and click on “YES” to
restart the system when prompted.
11 Insert the “Novell Client for Windows 95 v.2.5” CD in the CDROM and
execute “Setup.exe”.
12 Click on “Yes” to accept the License Agreement.
13 Select “Custom” installation and click on “Next”.
14 Select “Bindery (NetWare 3.x)” and click on “Next”.
15 Click on “Install” to start the installation.
16 Click on “Yes” to set the Preferred Server. (If you do not have the
required information, contact your network administrator).
17 Click on “Reboot” to complete the installation.
18 Right-click on the “Network Neighborhood” icon and select “Properties”.
19 Accept the default Network Protocols and the Primary Network Logon to
(Novell NetWare Client) as seen below and click on “OK”. (If you do not
have the required information, contact your network administrator)
20 Novell NetWare Client
Novell NetWare Client
Intel 82557C-based Ethernet PCI (10/100)
IPX 32-bit Protocol for the Novell NetWare Client
IPX/SPX-compatible Protocol
NetBEUI
21 Click on “OK” to accept the configuration.
Otros manuales para Vectra VEi7
1
Este manual sirve para los siguientes modelos
2
Otros manuales de Tarjeta PCI de Intel
Intel
Intel P55 Manual de usuario
Intel
Intel EXPI9301CT Guía de referencia
Intel
Intel Ether express PRO/100+ TX PCI model B Manual de usuario
Intel
Intel P67 Manual de usuario
Intel
Intel H67 Manual de usuario
Intel
Intel PCH-LP Instrucciones de funcionamiento
Intel
Intel RS3UC080 Manual de usuario
Intel
Intel Omni-Path Host Fabric Interface Series Manual de usuario
Intel
Intel Gigabit Ethernet Expansion Card Manual de usuario
Intel
Intel VCA 2 Manual de usuario
Manuales populares de Tarjeta PCI de otras marcas
Belkin
Belkin F5D7000F Manual de usuario
Pericom
Pericom PI7C7100 Manual de usuario
ADLINK Technology
ADLINK Technology cPCI-3548 Manual de usuario
Digium
Digium TE200 Series Manual de usuario
Allo.com
Allo.com 2nd Gen E1/T1/J1 Manual de usuario
Western Digital
Western Digital FireWire PCI Adapter Manual de usuario