Integral Audio MCSS630MW Manual de usuario

SKILL LEVEL REQUIRED APPLIES TO

INSTALLATION DIFFICULTY

INSTALLATION TIME

3 OUT OF 5

DO-IT-YOURSELF

4 HOURS

2012+ F30 W/O ACTIVE SOUND

DESIGN

OVERVIEW ........................................................................................................................................ 2

BEFORE YOU BEGIN .......................................................................................................................... 2

WHAT’S IN THE BOX - SOUNDSTAGE.................................................................................................. 3

WHAT’S IN THE BOX - SUBWOOFER................................................................................................... 4

TOOLS YOU WILL NEED...................................................................................................................... 5

INSTALLATION:

A. Prep Vehicle ........................................................................................................................ 6

B. Power & Ground Wiring........................................................................................................ 7

C. Signal Wiring....................................................................................................................... 8

D. Amplifier Installation & Speaker wiring............................................................................... 9

E. Soundstage speaker installation....................................................................................... 11

F. Install the Subwoofer [sub only]........................................................................................ 14

G. Settings ............................................................................................................................ 16

TIPS & TUNING................................................................................................................................ 18

TROUBLESHOOTING......................................................................................................................... 18

INSTALLATION GUIDE

SOUNDSTAGE + SUBWOOFER SYSTEM

FOR 2013+ BMW 3-SERIES (F30) ver. 5/2016

BEFORE YOU BEGIN

•Read this Guide completely BEFORE you begin.

•Disconnect the battery negative terminal while working on the vehicle.

•DO NOT PLACE THE KEY FOB in the vehicle with the battery connected and

the seat airbag wiring disconnected. Doing so will set off the airbag light,

and must be reset by your dealer.

•ALWAYS check behind panels and components before drilling, cutting,

or screwing into any part of a vehicle.

•This guide covers several different vehicle models and options. Some

steps only apply to certain installations. Steps images are labeled with

a black bar across the top:

-[SUBWOOFER ONLY] step applies only if you are installing the Integral Audio Subwoofer

System

-If there is no label, the step applies to ALL installations

-Because each kit applies to more than one vehicle, your kit may include extra items.

IMPORTANT

WHAT’S IN THE BOX

SOUNDSTAGE

I. SOUNDSTAGE SPEAKER PACKAGE

1. IASS-T 1” Silk Dome Tweeter (Pair)

2. IASS-4 4” Midrange (Pair)

3. IASS-6 6” Midwoofer (Pair)

II. SOUNDSTAGE CROSSOVER NETWORKS WITH

VEHICLE-SPECIFIC TUNING & EQUALIZATION

4. MCSS630MW Mid-Woofer Network (Pair)

5. MCSS630T Tweeter Network (Pair)

III. ARC AUDIO KS MINI AMPLIFIER (2CH W/

SOUNDSTAGE, 4CH W/SOUNDSTAGE + SUBWOOFER)

IV. SIGNAL & SPEAKER WIRING HARNESSES

6. Signal Wiring Harness (MCWH-SIG-R)

7. Mid-Woofer Connection Harness (Pair)

8. Tweeter Pigtail (Pair)

V. SOUNDSTAGE HARDWARE

9. Midrange Mounting Adapter (Pair)

10. Midwoofer Mounting Adapter (Pair)

11. #8 x 1/2” Midwoofer Mounting Screws (12)

12. #6 x 3/8” Midrange Mounting Screws (12)

13. Integral Audio Logo Badge (Pair)

VI. AMPLIFIER INSTALLATION & WIRING

14. Amplﬁer Power Wiring Harness (complete)

15. Threadlock Wire Splice Connectors (4) [HIFI/HK ONLY]

16. Threadlock Wire Tap (1)

17. Cable Ties (10)

18. 3M Electrical Tape

VII. AMPLIFIER MOUNTING (REAR AMP MOUNT)

19. Ampliﬁer Mounting Bracket

20. M6 Flange Nut

21. Screw Grommet

22. #8 x ½” Truss Head Screw (1)

23. #6 x 3/8” Pan Head Screw (4)

VIII. FACTORY A-PILLAR TRIM W/TWEETER MOUNTS

Continued on the next page . . .

WHAT’S IN THE BOX

SOUNDSTAGE

I. SOUNDSTAGE SPEAKER PACKAGE

1. IASS-T 1” Silk Dome Tweeter (Pair)

2. IASS-4 4” Midrange (Pair)

3. IASS-6 6” Midwoofer (Pair)

II. SOUNDSTAGE CROSSOVER NETWORKS WITH

VEHICLE-SPECIFIC TUNING & EQUALIZATION

4. MCSS630MW Mid-Woofer Network (Pair)

5. MCSS630T Tweeter Network (Pair)

III. ARC AUDIO KS MINI AMPLIFIER (2CH W/

SOUNDSTAGE, 4CH W/SOUNDSTAGE + SUBWOOFER)

IV. SIGNAL & SPEAKER WIRING HARNESSES

6. Signal Wiring Harness (MCWH-SIG-R)

7. Mid-Woofer Connection Harness (Pair)

8. Tweeter Pigtail (Pair)

V. SOUNDSTAGE HARDWARE

9. Midrange Mounting Adapter (Pair)

10. Midwoofer Mounting Adapter (Pair)

11. #8 x 1/2” Midwoofer Mounting Screws (12)

12. #6 x 3/8” Midrange Mounting Screws (12)

13. Integral Audio Logo Badge (Pair)

VI. AMPLIFIER INSTALLATION & WIRING

14. Amplﬁer Power Wiring Harness (complete)

15. Threadlock Wire Splice Connectors (4) [HIFI/HK ONLY]

16. Threadlock Wire Tap (1)

17. Cable Ties (10)

18. 3M Electrical Tape

VII. AMPLIFIER MOUNTING (REAR AMP MOUNT)

19. Ampliﬁer Mounting Bracket

20. M6 Flange Nut

21. Screw Grommet

22. #8 x ½” Truss Head Screw (1)

23. #6 x 3/8” Pan Head Screw (4)

VIII. FACTORY A-PILLAR TRIM W/TWEETER MOUNTS

Continued on the next page . . .

WHAT’S IN THE BOX

SUBWOOFER

IX. MC1101S SUBWOOFER ENCLOSURE

X. SB ACOUSTICS 10” SUBWOOFER

XI. SUBWOOFER COVER PANEL

XII. SUBWOOFER HARDWARE

24. Neutrik Speak-On Terminal & Gasket

25. #10 x 2.5” Pan Head Screw (3)

26. #10 x 1.5” Pan Head Screw (6)

27. ¼” x 1” Hex Head Bolt

28. #10 x 1” Black Pan Head Screw (8)

29. #10 x ¾” Pan Head Screw (8)

30. #4 x ½” Black Flathead Screw (2)

31. Threaded Insert (3)

32. Threaded Insert Installation Wrench

33. Cup Washer (6)

34. Rubber Stand-off (9)

35. Subwoofer Mounting Bracket (2)

36. Rosette Thumbscrew (2)

37. Connection Harness (Sub to Neutrik)

XIII. REMOTE LEVEL CONTROL

38. Integral Audio Remote Level Control

39. 3M VHB Double-Sided Mounting Tape (3in)

SeSelect Hardware for Identiﬁcation:

2725 29

231211223028

TOOLS YOU WILL NEED

6Images Not to Scale

I. PLASTIC PANEL REMOVAL TOOLS

II. TORX BITS:

1. T25

2. T30

3. T40

4. T50

III. DRILL

IV. DRILL BIT:

5. 7/16” [MUST be correct size!]

V. WRENCHES OR SOCKETS:

6. 7/16”

7. 8mm

8. 10mm

9. 10mm Deep [optional}

10. 19mm

VI. ELECTRICIAN’S WIRE FISH

VII. SCISSORS

VIII. UTILITY KNIFE

IX. PLIERS

X. CENTER PUNCH [SUB ONLY]

XI. WIRE STRIPPER [HIFI/HK ONLY]

XII. PICK & HOOK SET [OPTIONAL]

XIII. MAGNETIC PARTS TRAY [OPTIONAL]

PREP VEHICLE

1. REMOVE BATTERY COVER

Remove battery cover by turning the locking knob and lifting out

the cover.

2. DISCONNECT BATTERY NEGATIVE TERMINAL

Disconnect battery negative terminal with 10mm deep socket.

3. REMOVE TRUNK FLOOR PANEL

Remove the trunk oor panel.

4. REMOVE TRUNK CENTER BIN (STEP 1)

Locate the center pin of the expansion clip at the forward passen-

ger side corner of the liner.

5. REMOVE TRUNK CENTER BIN (STEP 2)

With a plastic panel removal tool, pry out center pin of the expan-

sion clip. Pry out clip base. Remove bin liner.

PREP VEHICLE

6. REMOVE TRUNK REAR SILL

Remove the trunk rear sill by removing the (4) center pin expan-

sion clips along the inner side. Lift the lower front edge of the sill

forward to clear the D-rings, then give a rm lift up to release the

friction clips holding the upper portion.

7. FOLD DOWN DRIVER SIDE REAR SEAT

Pull the rear seat release located in the trunk, fold down the driv-

er-side rear seat.

8. REMOVE DRIVER-SIDE REAR QUARTER PANEL TRIM (STEP 1)

Locate the luggage D-ring tie down at the forward driver-side of

the trunk. Pry off the black plastic cover. Remove the Torx T-40

screw. Lift out the D-ring assembly.

9. REMOVE DRIVER-SIDE REAR QUARTER PANEL TRIM (STEP 2)

There are (3) center-pin expansion clips that fasten the rear quar-

ter panel trim to the car - locate & remove the one in the upper

part of the rear cubby area.

10. REMOVE DRIVER-SIDE REAR QUARTER PANEL TRIM (STEP 3)

Then locate & remove the one on the side, under the parcel shelf

area. This one is attached to a plastic bracket. Remove the ex-

pansion clip on the upper portion of the bracket, and leave the

bracket attached to the quarter-panel trim.

POWER & GROUND WIRING

11. REMOVE DRIVER-SIDE REAR QUARTER PANEL TRIM (STEP 4)

Then locate & remove the one on the forward edge of the panel,

by the rear seat back.

12. REMOVE DRIVER-SIDE REAR QUARTER PANEL TRIM (STEP 5)

Now remove the trim panel. Start at the forward edge. Lift clear/

free the forward edge from behind the trim at the sides of the

rear seat backs and pull the panel out 4-6 inches.

DO NOT COMPLETELY REMOVE YET!

13. REMOVE DRIVER-SIDE REAR QUARTER PANEL TRIM (STEP 6)

Free panel edge along area (1). Then carefully open the split in

the panel at area (2) by pulling the split directly apart (i.e. not

sideways) and free the panel from around the trunk support arm.

DO NOT COMPLETELY REMOVE YET!

14. REMOVE DRIVER-SIDE REAR QUARTER PANEL TRIM (STEP 7)

Disconnect the plug on the back of the 12V power outlet, then

remove the panel from the vehicle.

15. REMOVE PLASTIC COVER

Remove the nut fastening the plastic cover over the amp with a

10mm socket. Remove the cover.

SIGNAL WIRING

16. REMOVE THE FACTORY AMPLIFIER & BRACKET

Using a 10mm socket, remove the nut fastening the factory am-

plier bracket to the vehicle. Slide the amplier bracket forward

to clear the mushroom studs and remove the amp and bracket.

17. DISCONNECT FACTORY AMPLIFIER HARNESS

Disconnect the factory wiring harness from the amplier by

pressing in the locking tab (1) and sliding the locking lever (2) to

the left as viewed in the image.

18. REMOVE THE FACTORY AMPLIFIER FROM THE BRACKET

Using an 8mm socket, remove the machine bolt that fastens the

factory amplier to the bracket. Slide the amplier off the brack-

et (you may need to gently use a screwdriver to free the amp from

the bracket).

19. RELOCATE FACTORY AMPLIFIER (STEP 1)

Loosen/free the 12V power outlet wire bundle by sliding the plas-

tic retaining clip off the mounting stud.

20. RELOCATE FACTORY AMPLIFIER (STEP 2)

Loosen/free the sound liner by removing the center pin expansion

clip. Pull the sound liner down and forward to access the area

behind it.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema estéreo para automóvil de Integral Audio

Integral Audio

Integral Audio IASS-T Manual de usuario

Integral Audio

Integral Audio Soundstage Series Manual de usuario

Integral Audio

Integral Audio SoundstageDSP Manual de usuario

Manuales populares de Sistema estéreo para automóvil de otras marcas

JL Audio

JL Audio Stealthbox SB-CAN-G2MVX3D/10TW3 Manual de usuario

Clarion

Clarion PU-9836A Manual de usuario

Sony

Sony MEX-BT5750U Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AR0M Manual de usuario

Sony

Sony RM-X7BT Manual de usuario

Insignia

Insignia NS-HD5113 Manual de usuario

Clarion

Clarion BTD3341 Manual de usuario

USA SPECS

USA SPECS PA11-VW6 Manual de usuario

Sony

Sony MEX-N4380BT Manual de usuario

Kenwood

Kenwood KCD-BT6544U/UY Manual de usuario

JVC

JVC KD-DB912BT Manual de usuario

Philips

Philips CSQ405/98 Manual de usuario

Alpine

Alpine TDM-7544 Manual de usuario

Autotek

Autotek TransAm TA 1400 Manual de usuario

Clarion

Clarion PN-3124N-A Manual de usuario

Denso TEN

Denso TEN FT0108A Manual de usuario

Pyle

Pyle PLD57MU Manual de usuario

Harman

Harman Chrysler Radio Navigation System RB4 Manual de usuario