Instanta 3001F Guía

SureFlow Series: 1501F & 3001F

Auto-Fill Catering Water Boiler

With Integrated Multi-Filter

Installation And User Instructions

INSTANTA LIMITED

Canning Road, Southport, Merseyside, PR9 7SN

Tel: (01704) 501114 Fax: (01704) 501115

IB31 - ISS: 02

The Professional’s Choice

CONTENTS

CONTENTS & INTRODUCTION 2

SAFETY INFORMATION 2

ENVIRONMENTAL INFORMATION & DELIVERY CHECK-LIST 3

TECHNICAL SPECIFICATION 3

INSTALLATION 3

OPERATION 4

DAILY USE 4

FILTER & FILTER REPLACEMENT 4

ADJUSTING FILTER-MONITOR (optional) 6

CLEANING 6

MAINTENANCE, SPARES & SERVICE INFORMATION 7

SERVICE / TECHNICAL SUPPORT / GUARANTEE 7

SERVICE WARNINGS & FAULT DIAGNOSTICS 8

Introduction

Dear Customer,

Thank you for purchasing this Instanta product.

Your new water boiler is designed to give

you years of trouble-free service provided

that the instructions contained in this manual

are followed.

All new series Instanta products are energy

ecient, simple to operate and easy to service.

Find out more about Instanta products at

www.instanta.com

Safety Information

Please read the following

carefully before starting work on

this equipment.

A competent person should install this appliance

in accordance with the installation instructions

for this appliance and all relevant local and

national standards including the following:

• Health & Safety at Work Act

• IEE Regulations

• Local & national Building Regulations

• BS Codes of practice

• Water Supply Regulations

All personnel should be provided with sucient

training in the safe use of this appliance.

A warning notice displayed next to the

machine is often helpful in notifying users that

the appliance contains and dispenses near

boiling water.

• Inform users that certain surfaces will

become hot (especially the draw-o tap).

Care should be taken to avoid potential

injury from burns and scalding whilst

operating this appliance.

• In line with Health and Safety requirements

we recommend a risk assessment be carried

out after the boiler has been installed.

• Always disconnect the unit from the power

supply before servicing.

• The unit must be earthed.

• Keep these instructions in a safe place near

the unit for future reference.

This appliance is not intended for use by

persons (Including Children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety. Children should be supervised to

ensure they do not play with the appliance.

Environmental (Information

On Disposal For Users

Of Waste Electrical &

Electronic Equipment)

The “crossed out wheelie bin” symbol on

this product means that discarded electrical

and electronic products should not be mixed

with general waste. Disposing of the product

correctly will help to save valuable resources

and prevent any potential negative eects

on human health and the environment which

could otherwise arise from inappropriate

waste handling. For proper treatment,

recovery and recycling of end-of-life products,

please contact your dealer or supplier for further

information, or local authority for details of your

nearest designated collection point.

Delivery Checklist

Before starting installation, check that you have

the following parts;

• Catering Water Boiler

• Drip-tray

• Drip-tray tting kit

• White water inlet hose (3/4”BSP connection)

• User instructions

Technical Speciﬁcation

Model 1501F 3001F

Width mm 252 310

Depth mm 518 518

Height mm 610 618

Power Rating KW 3.0 3.0

Weight (Empty) KG 13.5 15.5

Weight (Full) KG 28 36

Water Inlet Pressure: Bar 2 to 7 2 to 7

Installation

The boiler must be installed on a level work

surface with sucient strength to support

its weight. Ensure all vents are unobstructed.

Locate in an area where there is adequate space

to use the boiler safely (e.g. free from risk of

congestion and tripping hazards).

Connection to Mains Water Supply:

Connect the WRAS approved water lling hose

(3/4”BSP) to the inlet connection point on the

back of the boiler and the other end to the mains

water supply, via an accessible isolating tap with

a ¾”BSP thread*.

IMPORTANT: If micro-bore pipe is used instead

of the inlet hose supplied, the size must be

minimum OD 3/8”(10mm).

The water supply must have a pressure not

exceeding 7bar (96psi), and no lower than 2bar

(20psi) NOTE: If your water pressure exceeds

7bar, t a suitable pressure reduction valve.

We regret that Instanta cannot be held

responsible for any machine malfunctions if

the water pressure exceeds that stated. If in

doubt, consult your water supply company.

*To meet WRAS installation requirements, an

approved single-check valve providing back-

ow prevention protection, should be tted

at the point of connection between the water

supply and the appliances.

Electrical Connection:

The boiler must be Earthed.

Your machine is supplied with a standard 13amp

bonded plug with a 13amp fuse.

Overﬂow:

The drip-tray has a limited capacity and is

designed to handle small spillages and drips.

Wherever possible, we strongly recommend

that it is connected to a permanent waste outlet

using the tting kit provided.

If preferred, and as an alternative, the

overow can be connected from the back of

the machine using an optional rear-overow

kit (Pt. No: ROFK1) available from Instanta

Spares Department (01704 502905).

IMPORTANT: Whichever overow connection is

chosen, the diameter of the pipe used must be

no less than 15mm.

Failure to connect the overow-outlet to a

permanent waste of drain, could lead to property

damage from ooding.

If in all circumstances, it is absolutely not

possible to direct the boiler overow-outlet to

a permanent waste or drain, then the mains

water supply to the boiler should be isolated

and the unit switched o whenever it is left

unattended for long periods (e.g. overnight).

Whilst every reasonable precaution is taken

to prevent an overﬂow, Instanta cannot be

held responsible for any damage caused as a

result of incorrect installation or blockage of

the overﬂow or failure to direct the overﬂow

to a safe outlet.

Operation

First use (once water and electrical connections

have been made);

• Switch boiler on. The screen will light up red

and will run through an initial self-diagnostic

check before starting to ll with water

(screen reads; “NOT READY FILLING”).

• Once primed with water, the boiler will

begin to heat (screen reads;

“NOT READY HEATING”).

• When the correct temperature has been

reached, the display will change from Red

to White and will simply read “READY”.

• The boiler will then continue in a heat/

ll cycle until the tank is at full capacity.

(During the heat/ll cycle, small amounts of

water are added to ensure the water at the

tap is always at the correct temperature).

IMPORTANT NOTE: In normal daily use, the

boiler may be used as soon as the “READY”

message is displayed, but on rst install, wait

at least 15 minutes before starting to use.

• Drain o approximately 10 litres of water

(to ush the new lter cartridge through).

• The boiler is now ready for use.

Regular Daily Use

Switch boiler on and wait for the screen to turn

white and show “READY” message. The water

will then be at the correct temperature.

Dispense water via the lever tap.

(CAUTION: Boiler dispenses near-boiling water).

AQ35 Multi-Filter

Instanta’s new built-in ltration system ensures

that water is always to the highest standard,

whilst delivering lower maintenance costs and

improved energy eciency.

Quick and easy to change, the new lter reduces

sediment, chlorine taste & odour, and lime-scale

via a slow release scale inhibitor, providing

better water and therefore, better quality drinks.

Filter Replacement:

A series of bars on the FILTER display shows

the estimated remaining life in the current

lter cartridge. When the lter has just 200

Litres remaining, the lter icon will begin to

ash as a reminder. When the lter needs

replacing, the screen will show the message;

“CHANGE FILTER”.

The boiler will continue to operate with the

CHANGE FILTER screen but scale may build

up more rapidly and the water taste may

be aected.

Replace the lter as follows;

1. Switch boiler o and draw water down

to tap level.

2. Grip cartridge and rotate a quarter-turn to

the left and pull forward. CAUTION: A small

amount of water will drain from the head.

3. Align a at screw-driver or similar with the tab

on the lter and gently push.

4. With one tab loosened, pull the lter cap o

the old cartridge.

5. Align the shape on the inside of the lter cap

(highlighted above) with the shape on the end

of the new lter and push the two together

until it clicks rmly in place.

6. Remove protective cap from the top of the

new cartridge and ensure the two rubber

seals are in place.

7. Insert new cartridge and turn until it locates.

Install with a quarter-turn to the right

until cartridge comes to a complete stop

(Inlet water will automatically turn on).

8. Switch boiler back on and allow to ll

(15 minutes).

9. Drain-o approximately 10 litres of water.

10. TO RESET FILTER MONITOR: …Press and

hold “On/O” button, screen will go blank

but continue to hold, until “READY” message

is displayed on a red screen.

The boiler is now ready for use.

Adjusting Filter Monitor

(Optional):

The lter monitor is factory-set to “medium”

(default) which is suitable for most parts of the

UK with average or medium water hardness.

Hard and Soft Water: The eectiveness of

the lter will be reduced in hard water areas

(and should be replaced more frequently),

or extended in soft water areas where scale

is less of a problem.

If in doubt as to the hardness of water supplied

in your area, consult your local water authority or

Instanta Technical Support.

The lter monitor on the boiler can be changed

from the default “medium” setting to “hard” or

“soft” setting as follows;

Replace the lter cartridge (as steps 1 to 9

“AQ35 Filter Replacement” above). Then;

• Turn machine o.

• Press & hold “on/o” button (for

approximately 12 seconds) until red screen

shows “PR” in top-right corner, then release

button. Temperature setting is displayed.

• Press & hold button (long push)

for approximately 5 seconds until

screen changes to show “medium”

(default lter setting).

• Press button (short push) to scroll

between the dierent lter settings;

SOFT

MEDIUM

HARD

EMPTY FILTER SYMBOL (No Filter monitor).

• With the required lter setting selected,

Press & hold button (long push) for

4 seconds to save.

• Press & hold button (long push) for

approximately 6 seconds until display

goes blank.

• Turn machine back on again.

• TO RE-SET & CONFIRM NEW SETTINGS;

…Press & hold button, screen will go

blank but continue to hold, until “READY”

message is displayed on a red screen

(See; Step 10 above).

Cleaning

• Clean the external surfaces of the boiler

regularly to maintain good hygiene

• Empty the front drip-tray regularly

• Wipe external surfaces of the boiler with a

damp cloth. Do not use abrasive materials

on the outer surfaces.

• Wipe the draw-o tap each day to keep

clean and also prevent lime-scale deposits

from building up around the tap-outlet.

Maintenance & Service

Information

Filter:

Twist to the left and remove. See “AQ35

Filter Replacement” section above.

Descaling:

The boiler should be periodically checked for

scale build-up…see below:

In hard water areas, the boiler should be

descaled on a regular basis to maintain ecient

operation, minimise energy consumption, and

also retain the water quality. The frequency

depends on the hardness of the local mains

water supply and the regular replacement of

the AQ35 lter cartridge.

To de-scale:

• Disconnect machine from power supply

• Empty the machine through the draw-o

tap and allow to cool

• Lift o the outer-lid.

• Remove tank-lid (four xing screws).

• Lift out the evaporation plates (inside of

tank – Remember order of removal).

• Remove as much scale as possible by hand.

Any scale which is dicult to remove can be

dissolved by using a de-scaling solution.

• Wipe clean the level sensing probes.

• Flush with copious amounts of cold water to

ensure all traces of de-scaler are removed

before using the boiler again.

• Replace evaporation plates, tank-lid and

outer lid.

Draw-off tap:

The draw-o tap components are subject to

wear & tear. We strongly recommend that the

tap is inspected periodically (at least once a

year as part of a general maintenance routine).

It is advisable to keep a spare tap assembly in

case of emergencies.

Accessories & Spares (Tel: 01704 502905)

Tap Washer - TP1001/L

Tap Spring - TP1007/N

Tap Bonnet - HSTP100

Upper Tap Assembly - XTP1050/A

A full range of spares and accessories are

available from our spares department.

Service Warnings And Fault

Diagnosis

Your boiler is tted with an intelligent fault diagnosing

system and is able to detect various fault conditions.

Some of these are less serious and the machine will

continue to operate as normal, while others are more

serious and will disable the unit.

Before calling for service, switch the machine o

at the mains supply. Draw-o a small amount of

water and then switch back on after 10 minutes.

If the fault does not clear, call technical support

for advice.

The majority of possible faults have been

covered above. However, in certain

circumstances, safely controls within the

boiler may be activated. There are two

resettable safety cut-outs in your boiler:

1). Over-boil safety cut-out; (activates should

the boiler produce excess steam). This can be

due to;

- lime-scale within the tank,

- a temporary interruption in the water supply,

- a faulty temperature sensor.

To reset boiler; Switch o at the mains power

supply and allow the boiler to cool down for ten

minutes before switching back on (the safety

device should automatically reset).

2). Boil-dry safety cut-out – this will activate if

the boiler has been boiled dry, for example,

due to lime-scale build-up or water starvation.

If the boil-dry cut-out has activated, this will

require a manual reset. Contact Instanta

Technical Support department for assistance

with this.

Service/Technical Support:

Tel: 01704 502911

To ensure your service enquiry is handled

as eciently as possible, please have the

following information available;

• Brief description of problem

• Product Type (model)

• Serial Number (label on right-hand side

of machine). This is essential.

Guarantee

Your boiler is guaranteed for two years from date

of installation.

Our guarantee includes on site labour and parts

for problems caused by fault of manufacture and

component failure with the following exclusions:

• Problems caused by hard water and

lime scale. We regret that we cannot be

held responsible for problems caused by

hard water.

• Dripping Taps. These components are

subject to wear and tear but in the event

of a tap failing within twelve months of

installation, we will be pleased to replace the

tap assembly by post. Fitting is very simple

and requires no tools. An engineer call out is

not necessary.

• Accidental damage, misuse or use not in

accordance with these instructions and

damage caused by incorrect installation.

• The manufacturer disclaims any liability for

incidental, or consequential damages.

Safety Caution: Isolate boiler from

power supply before removing any

outer panels or attempting any reset.

FM 36413 EMS 75807

Este manual sirve para los siguientes modelos

Otros manuales de Caldera de Instanta

Manuales populares de Caldera de otras marcas

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manual de usuario

Radijator

Radijator BIO max 23.1 Manual de usuario

Brunner

Brunner BSV 20 Manual de usuario

Buderus

Buderus Logamax GB062-24 KDE H V2 Manual de usuario

Potterton

Potterton 50e Hoja de datos

UTICA BOILERS

UTICA BOILERS TriFire Manual de usuario

Joannes

Joannes LADY Series Manual

ECR International

ECR International UB90-125 Manual de instrucciones

Froling

Froling FHG Turbo 3000 Manual de usuario

Froling

Froling P4 Pellet 8 - 105 Manual de usuario

U.S. Boiler Company

U.S. Boiler Company K2 Manual de usuario

Henrad

Henrad C95 FF Manual de usuario

NeOvo

NeOvo EcoNox EF 36 Manual de usuario

Potterton

Potterton PROMAX SL 12 Manual de usuario

Eco Hometec

Eco Hometec EC 25 COMPACT Manual de usuario

Viessmann

Viessmann VITODENS 200 Guía

Baxi

Baxi Prime 1.24 Manual de usuario

REXNOVA

REXNOVA ISA 20 BITHERMAL Manual de usuario