Insta 718 Manual de usuario

MNL90002 Rev. P 02.16.15

OPERATION AND MAINTENANCE MANUAL

MODEL 718/728/828

FOR USE BY QUALIFIED PERSONNEL ONLY

Safety Summary

International Symbols

Safety

Summary

WARNING

In case of power cord damage,

do not attempt to repair or

replace the power cord.

Contact the manufacturer or

the local distributor

International

Symbols

Power Off

Power On

the

local

distributor

WARNING

For protection against fire and

electric shock, replace with

same type and rating fuse.

Fuse rated max. 1 amp 120V.

Hot Surface

Risk of Electrical Shock

Protective Earth

Terminal

WARNING

Hot Surface. Avoid contact.

CAUTION

D ring normal operation the

Protective

Earth

Terminal

Start Action

Disengage

ring

normal

operation

the

base of the machine needs to

be installed or placed above

the wall socket.

CAUTION

The recommended input

h ll t d 100

Ground

Caution - Warning

pressure s

excee

100

psi. The operating pressure is

from 30 – 100 psi.

CAUTION

The operation may be

terminated by pressing the

DISENGAGE

sitch

DISENGAGE

itch

CAUTION

The machine is to be operated

by one person only.

CAUTION

To reduce the risk of electric

shock and injury to persons,

disconnect from power supply

before servicing and /or

cleaning.

FOR USE BY QUALIFIED PERSONNEL ONLY

Congratulations!

Limited Machine Warranty

Congratulations!

Your selection of the Insta Graphic Systems heat seal

machine is a sound business decision. Insta

equipment is the result of the highest quality

engineering and time-tested design. Your new

machine combined with Insta's reputation of

innovation in the heat

sealing field insures the

Limited

Machine

Warranty

Insta Graphic Systems warrants this heat seal

machine, when operated under normal conditions, to

be free from manufacturing defects in material and

workmanship for a period of one year on parts

(lifetime on the heating element) and 90 days on labor

m th

inv

innovation

the

heat

sealing

field

insures

the

continuing capability of delivering the best-decorated

substrates possible.

This manual describes installation, operation, and

maintenance procedures for your 700/800 series

machine, as well as easy to use instructions for on-

the-spot maintenance.

oeocedae

This warranty will be effective only when Insta

authorizes the original purchaser to return the product

to the factory in Cerritos, California, freight prepaid,

and only when the product upon examination has

proven to be defective.

Thi t d t l t hi th t h

Your machine will have a long, trouble free life. Read

this manual. Keep it with your machine; it's your key

to proper operation and lasting service.

Thi

s warran

oes no

app

o any mac

been subjected to misuse, negligence or accident.

Insta shall not be liable for the injury, loss or damage,

direct or consequential, arising out of the use or the

inability to use the product.

kin

r in

nt th

General Description

oca o a y ds a begeae a ou a

the sale price of the product or part to which claim is

made.

This is the sole warranty given by the company, it is in

lieu of any other warranties, expressed or implied, in

law or in fact, including the warranties of

merchantability and fitness for a particular use, and is

td hb th h i tki dli

The 718, 728 and 828 are Automatic Swing Away

machines generating and distributing evenly

tremendous pressure throughout its upper and lower

platens. These machines are essential in the

application of sublimation transfers. Its cast-in tubular

heating element heats the metal from within, to

accep

as suc

e purc

aser

very

of this product.

produce constant and long lasting heat. The 718

machine has 15” x 15” platens; the 728 has 15” x 20”

platens; the 828 has 20” x 25” platens.

FOR USE BY QUALIFIED PERSONNEL ONLY

DfPtti

Installation

DOMESTIC – 700 SERIES

Use a separate 15 amp AC circuit.

Only industrial extension cords with

proper wire size should be used:

size 16/3 wire for distances u

to 25

egree o

IP (Ingress Protection) rating according to IEC

60529.

NOTE

IEC 60529 does not specify sealing

effectiveness against the following:

feet, and size 14/3 for distances up

to 50 feet.

INTERNATIONAL – 700 SERIES

Use a designated 16 amp AC

circuit. Only industrial extension

cords with proper wire size (2.5 sq.

mm) shall be used.

effectiveness

against

the

following:

mechanical damage of the equipment; the

risk of explosion; certain types of liquid

conditions, e.g. those that are produced by

condensation; corrosive vapours; funus;

vermin

mm)

shall

used.

DOMESTIC – 800 SERIES

Use a separate 230/240 20 amp AC

circuit. Only industrial extension

cords with proper wire size should

be used: size 16/3 wire for distances

up to 25 feet, and size 14/3 for

di 0 f

IP54=IP

1st Digit5

2nd Digit4

1st

Di it

Protection from

lid bj t

2nd

Di it

Protection from

stances up to 5

eet.

INTERNATIONAL – 800 SERIES

Use a designated 20 amp AC

circuit. Only industrial extension

cords with proper wire size (3.3 sq.

mm) shall be used.

lid

ure

0 Non protected 0 Non protected

1Objects greater

than 50mm 1 Dripping water

ects

reater

Dripping water

when tilted up to

Specifications

MODEL 718/728/828

Voltage 120 Volts AC 50/60 Hertz

Model 718 1500 Watts 12.5Amps

Model 728

1750 Watts 14 6 Amps

than 12mm

when

tilted

15 deg.

3Objects greater

than 2.5mm 3 Spraying water

4Objects greater

than 1mm 4 Splashing water

Model

728

1750

Watts

Amps

Voltage 240 Volts AC 50/60 Hertz

Model 718 1500 Watts 6.3 Amps

Voltage 230 Volts AC 50/60 Hertz

Model 728 2200 Watts 9.6 Amps

Model 828 3300 Watts 14.4 Amps

5 Dust protected 5 Water jets

6 Dust tight 6 Heavy seas

-- --- 7 .15m – 1m

immersion

1m +

Model 718 Machine Weight 128 Pounds (58.1 KG)

Model 728 Machine Weight 143 Pounds (64.9 KG)

Model 828 Machine Weight 218 Pounds (98.9 KG)

-- ---

submersion

FOR USE BY QUALIFIED PERSONNEL ONLY

Oti

pera

1. Push POWER/MODE button on the controller

to turn ON machine. Hold POWER/MODE for

3 seconds to turn off machine.

2. Set desired temperature and select the

9. Swing away the upper platen to the opposite

side and remove substrate.

10. The DISENGAGE button may be pushed at

anytime to deactivate the machine.

desired timing cycle (see controller operation).

Swing the upper platen arm to its fully open

position, away from lower platen.

3. Allow the machine to warm up until the

selected temperature is reached.

NOTE

The air filter may be loose a little to

hinder the bowl from breaking

during handling. Do not touch the

polycarbonate bowl with synthetic

grease during operation and

maintenance Make sure your hands

4. Set the desired pressure by adjusting the air

pressure regulator.

5. Place the substrate on lower platen,

smoothing out all wrinkles.

6. Position transfer or letterin

on substrate.

Environmental Conditions

Only operate Insta heat seal machines under

suitable environmental conditions

maintenance

Make

sure

your

hands

are clean before touching the air

filter bowl.

7. Swing the upper arm into position directly

over the lower platen.

suitable

environmental

conditions

1. Placed on a even, non flammable surface.

2. Can support a minimum of 300 lbs. if placed

above a platform.

Dttit tth i

SAFETY DELAY FEATURE

For operator safety the machine

shall

not operate

unless the upper

Depress and hold both start buttons

o no

res

access

e ma

n power

switch.

4. Maintain a clearance around any forms of

liquid.

5. Do not over extend the power cord.

shall

not

operate

unless

the

upper

platen has fully reached the left

hand position. An additional safety

delay has been incorporated in

machines running software 2.29

(see point 8).

Depress

and

hold

both

start

buttons

simultaneously until the lower platen contacts

the upper platen. The start buttons must be

held until the upper and lower platens

make contact. At this point the machine

operation is fully automatic. The platens seal

the transfer to the substrate and then release

automatically at the end of the selected timing

6. The operational voltage should not be 10%

max/min of the rated value.

7. Avoid voltage spikes.

8. Sound pressure level at operator station does

automatically

the

end

the

selected

timing

cycle. not exceed 70dB (A).

FOR USE BY QUALIFIED PERSONNEL ONLY

Solid State Controller:

CtllO ti

Model 718 shown

pera

1. Select the desired preset program by pressing

the PGM button until the LED above the PGM

button indicates the desired setting.

2. If a settin

other than the pro

rammed

This controller has three (4) control features:

presets are desired, press the PGM button

until none of the LED's above the PGM

button are lit.

3. Changing the Temperature

• Press the POWER/MODE (or MODE)

button until temperature is displayed.

1. Temperature - Temperature can be set from

125 - 450°F (52-232°C).

2. Time - Time can be set from 1 second to 10

minutes.

3. Counter

–

cle counter counts the number of

• Press and hold SET button in while

pressing the UP (↑) or DOWN (↓) arrow

buttons to the desired temperature

setting.

4. Changing the Timer

• Press the POWER/MODE (or MODE)

button until timer is displayed

applications from 1 to 9999 (see additional

Notes – Counter).

4. Presets - Five (5) presets that can be

programmed by the user. Each preset will

retain a temperature and time setting, i.e.

Program #1 could be set for 325

F and 10

button

until

timer

displayed

• Press and hold SET button in while

pressing the UP (↑) or DOWN (↓) arrow

buttons to the desired timer setting.

NOTE

Program

could

set

for

325

and

seconds while Program #2 could be set for

375°F and 15 seconds. Once the five presets

have been programmed, the user need only

press the PGM button repeatedly until the

desired program is selected. The lit LED

above the PGM button indicates the selected

program

Note: there is also a sixth setting

The DISENGAGE switch (located in

the center of the instrument panel)

may be pushed at any time to

deactivate the machine. The cycle

will stop immediately, and the timer

will reset.

program

Note:

there

also

sixth

setting

that is indicated by no lit LED's.

FOR USE BY QUALIFIED PERSONNEL ONLY

S tti th P t

NOTE

tti

rese

1. Push and hold both the POWER/MODE (or

MODE) and PGM buttons for 3-5 seconds

until one of the programs LED's starts to blink.

This is the programming mode.

NOTE

When the machine is operating with

none of the five program LED's lit,

i.e. no presets, the time and

temperature WILL BE SAVED even

if the power is turned off. The

presets will also be saved when the

it dff

Additional Notes

Timer

2. A blinking LED above the PGM button

indicates which preset is active.

3. Select a program (1,2,3,4,or 5) by pressing

the PGM button.

4. Settin

Tem

erature

power

urne

• The controller has a count down timer, which

automatically disengages (opens) the machine

at the completion of the application.

• Timer display is minutes:seconds. Range is

00:00 to 10:00, Colons (:) flash while timer is

running

• Press the POWER/MODE (or MODE)

button until temperature is displayed.

• Press and hold SET button in while

pressing the UP (↑) or DOWN (↓) arrow

buttons to the desired temperature

setting.

NOTE

running

NOTE

The DISENGAGE switch (located in the

center of the instrument panel) may be

pushed at any time to deactivate the

machine. The cycle will stop

immediately, and the timer will reset.

5. Setting Time

• Press the POWER/MODE (or MODE)

button until time is displayed.

NOTE

If a Fahrenheit/Celsius change is

desired, see Additional Notes –

Temperature.

Counter

The controller has a built in cycle counter.

button

until

time

displayed.

• Press and hold SET button in while

pressing the UP (↑) or DOWN (↓) arrow

buttons to the desired timer setting.

6. Repeat steps 3-5 until all five (5) presets have

the desired preset (temperature/time cycle).

• Press POWER/MODE (or MODE) button until

the counter is displayed.

• Counter display range is 0000 to 9999.

• To reset the cycle counter, display the counter

readin

then

ush and hold UP

(

↑

)

and

7. Push and hold both the POWER/MODE (or

MODE) and PGM buttons for 3-5 seconds

until a single beep sound is heard to exit the

programming mode.

NOTE

g, p

(

)

DOWN (↓) arrow buttons for 3 seconds until

the counter resets to zero (0000) on the

display.

When in the normal mode, none of the

five program LED's will be blinking and

the user cannot change the time and

temperature for any of the five presets.

FOR USE BY QUALIFIED PERSONNEL ONLY

Sleep Time

Slee

Time

Set Back

1. Press the POWER/MODE (or MODE)

button until the counter displays. Enter

the Factory Mode by pressing and

holding together SET then

POWER/MODE (or MODE)for3 to 5

seconds.

Temperature, Automatic Shut Off,

Temperature Conversion, and

Offset

Model 718 Shown

2. Press SET + UP or DOWN Arrow to set

Sleep Mode Time.

The Sleep Mode / Automatic Shut Off is designed

to save electrical consumption when the user is

not engaged in the usage of the Insta heat seal

machines for a pre-determined period of time

defined by the user.

Sleep

Mode

Time.

1._XX ; XX = Minutes from OFF to 99

+or

defined

the

user.

During activation, any disturbances such as the

key press or heat press cycle will reset the timers

for both Sleep Mode and Automatic Shut Off.

When the Automatic Shut Off is set to OFF and

the Sleep Mode is activated any disturbances to

Set Back Temperature

3. Press POWER/MODE (or MODE).

the

Sleep

Mode

activated

any

disturbances

the machine will disengage the Sleep Mode.

When the Sleep Mode is set to OFF, the timer for

Automatic Shut Off will activate and resets after

every pressed key or heat press cycle.

4. Press SET + UP or DOWN Arrow to set

Set Back Temperature.

+or

• Sleep Time

(Level 1 – Menu 1)

• Set Back Temperature

(Level 1 – Menu 2)

• Automatic Shut Off Time

(Level 1 – Menu 3)

•

Fahrenheit / Celsius

2._XXX ; XXX = Temp. from 225F to

300F

Fahrenheit

Celsius

(Level 1 – Menu 4)

• User Offset

(Level 1 – Menu 5)

FOR USE BY QUALIFIED PERSONNEL ONLY

Automatic Shut Off

5. Press POWER/MODE (or MODE).

Press

SET

UP or DOWN Arrow

to set

User Offset

9. Press POWER/MODE (or MODE).

10. Press SET + UP or DOWN Arrow to set

Press

SET

DOWN

Arrow

set

Auto Shut Off Time.

3._XX ; XX = Minutes from OFF to 99

+or

the Offset.

5._XX ; XX = Offset Number

+or

Temperature Conversion

POWER/MODE

(

MODE

)

Exit

11. Press and hold together SET then

POWER/MODE (or MODE) at any time

for

3 to 5 seconds

to Exit

ress

POWER/MODE

(

MODE

)

8. Press SET + UP or DOWN Arrow to set

Fahrenheit or Celsius.

+or

for

seconds

Exit

4._X ; X = F or C

FOR USE BY QUALIFIED PERSONNEL ONLY

PtiMit

reven

enance

Suggestions

The Insta heat seal machines are relatively

maintenance free. For long, trouble-free life, the

following preventive maintenance should be

followed:

reven

enance

Suggestions

7. Polycarbonate bowls and pressure gauges:

Avoid area with direct sunlight; impact blow or

temperature outside of the rated range.

followed:

1. Do not heat seal items such as buttons, pins,

snaps, or zippers that tend to cut the silicone

rubber pad or scratch the Teflon heat platen.

2. Periodically clean the Teflon-coated heat

platen with a non

abrasive piece of cloth

8. Do not expose/clean filter bowls with

detergents, chlorinated hydro-carbons,

keytones, esters or certain alcohols.

9. Do not expose the polycarbonate bowls or the

sight gauges in air systems where

platen

with

non

abrasive

piece

cloth

Stubborn stains may be cleaned, when

platen is cool, with mineral spirits.

3. When the heat platen is hot and not in use,

keep in open position (away from the silicone

rubber pad).

compressors are lubricated with fire resistant

fluids such as phosphate ester and di-ester

lubricants.

10. Remove excessive dirt, grime and clutter

from work area.

4. To prevent soiling of substrate, periodic wiping

of the entire exterior machine, including

platens, with a clean rag is recommended. If

necessary, use mineral spirits for cleaning a

cold machine. Since mineral spirits are

flammable, use precautions and keep away

fkflhthtlt

General Maintenance

It is recommended that you have the following

items available:

rom spar

ame, or

en.

5. The machine requires periodic lubrication with

a high-temperature, non-melting grease

(MPPL023). Lubricate the post and heat

platen’s pivot pin depending upon usage.

(Once every month if used continuously.)

A. Regular screw driver

B. Phillips head screw driver

C. Small adjustable wrench

D. Needle nose pliers with insulated handle

E. Set of Allen wrenches

F. Grease gun (MAPG010)

G. Special high temperature grease (MPPL023)

NOTE

Wipe off any excess oil or grease. WARNING

Power cord replacement should be

fth ft l

With the above items you should be able to

accomplish most repairs.

rom

e manu

urer on

(because it requires a special

prepared cord.)

6. Turn off air pressure when machine is not

being used.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Ahorrador de alimentos de Insta

Insta

Insta 138 Manual de usuario

Insta

Insta 909 Manual de usuario

Insta

Insta PUT IT ON 101 Manual de usuario

Insta

Insta 228 Manual de usuario

Manuales populares de Ahorrador de alimentos de otras marcas

Sonics

Sonics T202WD Manual de usuario

ABGENE

ABGENE ALPS 50V Manual de usuario

Teknika

Teknika MUL-331 Manual de usuario

MELAG

MELAG MELAseal 200 Manual de usuario

FoodSaver

FoodSaver FS1000 Series Manual de usuario

Thermopatch

Thermopatch NL-30 Manual de usuario

Signode

Signode B-250 Manual de instrucciones

AmeriVacS

AmeriVacS AVS-20 Manual de usuario

FoodSaver

FoodSaver V1085 Manual de usuario

Deni

Deni Freshlock 1831 Manual de usuario

CASO DESIGN

CASO DESIGN VC150 Instrucciones de instalación

Atmovac

Atmovac Santa Ana Manual de usuario

WAAGE

WAAGE SV-FOOD Manual

VacuWare

VacuWare Fresh Manual

Melissa

Melissa 16310179 Manual de usuario

Heinner

Heinner HAV-130WH Manual de usuario

NUTRICHEF

NUTRICHEF PKVS50STS Manual de usuario

U-Line

U-Line H-57 Manual de instrucciones