InSinkErator 2200 Manual de usuario

Instant Hot Water Dispenser

Owner’s Manual

Series 2200

Series 1100

SST-FLTR

Installation, Care & Use

Instalacion, cuidado & uso

Installation, soin et utilisation

Equipment You May Need:

We are delighted that you have chosen the InSinkErator®Instant Hot Water Dispenser

to be a part of your home. This unique appliance will save you time and effort in the

kitchen, and you’ll enjoy discovering new uses for it each day. That’s exactly why

millions of people are now using an InSinkErator Instant Hot Water Dispenser.

We are confident that by following our step-by-step instructions, you’ll soon be enjoying

the convenience of instant hot water.

For your satisfaction and safety, read all instructions, cautions, warnings and dangers before installing

or using this instant hot water dispenser.

This particular unit is not intended for commercial use.

Make sure that all electrical wiring and connections conform to local codes.

A standard 120-volt grounded electrical outlet is required under the sink for the dispenser’s electrical power.

The wall outlet powering your dispenser must have power supplied to it continuously.

This outlet must be fused and should not be controlled by the same wall switch that operates the

disposer, unless you have a SinkTop Switch™from InSinkErator®.

It is recommended that a dedicated control valve be installed on the cold water line supplying water

to this system.

If you suspect elevated levels of chlorine in your water, it is recommended to use our water

filtration system.

The use of a water filter should NOT result in the water pressure to drop below 30 psi (207kPa).

If it does, this will prevent your unit from operating properly.

Moving parts inside the tank causing a rattling noise is normal.

WHAT YOU SHOULD KNOW BEFORE YOU BEGIN

Equipment Required:

 Drill

 T-fitting

 Dedicated control valve

 Adjustable wrench

 Phillips and flat blade screwdrivers

 Pencil

 Tape measure

 Level

Anchors for drywall

Hole saw

Basin wrench

Hole punch

If you intend to use the sprayer hole in your sink for your dispenser, you may need a basin wrench and a

1/8" plug or a 1/4" cap (not supplied) for the faucet spray hose line.

See Step 1-B.

If you need to cut a mounting hole in your stainless steel sink, you may need a 11

⁄4" - 11

⁄2" hole saw made

for cutting stainless steel or a hole punch. Consult a professional if you are drilling into a surface other

than stainless steel.

WHAT YOU NEED TO GET STARTED

HOW TO USE THIS INSTRUCTION MANUAL

Provides a step-by-step narrative describing the installation step, with check boxes

that can be marked as you progress through the installation.

Contains simple illustrations that provide visual instruction to support the narrative.

CAUTIONS, WARNINGS and DANGERS that will require your attention during the step.

These instructions are separated into main sections, indicated by numbers, and subsections,

indicated by capital letters. The manual is setup this way to allow you to take a break at any

point after completing a section or subsection without affecting the installation process.

What you’ll see in the

instruction manual:

Identify the model of your instant hot water dispenser and record it here:________________

Property Damage: Do not pinch or break copper

tubing. Do not distort the last 1 inch of tubing.

INSTALLINGTHE FAUCET

Unpackdispenser components.

On a firm, flat surface, carefully

straighten the copper tubing.

An imminently hazardous situation, which, if not avoided, will result in death or serious injury.

A potentially hazardous situation, which, if not avoided, could result in death or serious injury.

A potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

F-HC1100 F-GN1100

F-GN2215F-HC2215

F-GN2200

F-HC2200

OVERVIEW OF A

COMPLETED SETUP

COMPONENTS IN THIS PACKAGE

SST-FLTR

Filter Head

3/8" Tubes(2) Filter

Discharge Tube

Filter Cartridge

3/4" Screws(4)

Brass Nut / Ferrule /

Tube Insert

F-HC1100 F-GN1100

F-HC2215 F-GN2215

F-HC2200 F-GN2200

Semi-circular

Mounting Plate

Rubber O-Ring Hex Nut

Hex Tool

QuickConnector

Plug (1)

Snap-Connect

Fitting (3 pieces)

The wall outlet for your dispenser must have power supplied to it continuously

and must be fused. It should not be controlled by the same wall switch

that operates your disposer, unless using an InSinkErator SinkTop SwitchTM.

PREPARATION

START HERE PROPER INSTALLATION SHOULD TAKE ABOUT 2-4 HOURS

Identify locations for the dispenser

faucet, tank and filter.

Check to make sure there is proper

clearance for dispenser handles to

be fully opened.

Check to make sure counter is 3"

thick or less.

Make sure there is a grounded

electrical outlet under the sink.

Turn off water supply.

If using the sink sprayer hose hole,

remove nut that connects sprayer

hose at bottom of faucet.

Using adjustable wrench, remove nut

connecting sprayer washer flange in

sprayer hole.

Plug hose opening with either a 1/8"

plug or a 1/4"cap (not supplied).

If you have to drill through sink or

countertop, you may need to rent or purchase

the appropriate tools.

Consult a professional before drilling into

a surface other than stainless steel.

CWhat if you don’t have a sprayer hole or

don’t want to use it?

Many homeowners replace the soap

dispenser in their sink with an instant

hot water dispenser.

If drilling a hole into a stainless steel

sink or counter top, you can cut a

mounting hole for the dispenser with a

hole saw for stainless steel, or you can

use a hole punch.

Required Hole Size

Hot & Cool Models 13⁄8" - 11⁄2"

Hot Only Models 11⁄4" - 11⁄2"

F-HC2215................31⁄8"

F-GN2215................37⁄8"

F-HC2200................31⁄8"

F-GN2200................37⁄8"

F-HC1100................31⁄8"

F-GN1100................37⁄8"

Required minimum from

center of hole to wall

Maximum counter

thickness is 3".

If installing ONLY new faucet or new tank, see Page 10.

Property Damage: Do not pinch or break copper

tubing. Do not distort the last 1 inch of tubing.

From under the sink, place the

semi-circular mounting plate onto

the threaded stud.

Place hex nut onto the threaded stud.

Ensure faucet head is at desired angle.

Insert screwdriver into hole on side of

hex tool (creating a “T”), and use tool

to tighten nut and secure faucet.

Semi-circular mounting plate should

encircle all descending tubes and

extend beyond sink hole when tight.

Ensure that the black O-ring is

properly seated in the base of the

dispenser head (the groove on the

underside of the dispenser).

Feed tubes down through the hole

in the sink or countertop until the

base is at rest on the sink or

countertop surface.

Unpack dispenser components.

On a firm, flat surface, carefully

straighten the copper tubing.

An assistant may be needed to hold

the dispenser head in place

while securing the dispenser.

Make sure to use rubber O-ring

to ensure proper seal.

INSTALLING THE FAUCET

ASelect a spot under the sink to mount

tank vertically within reach of both

plumbing and electrical connections.

The tank should be within 16"or less

of faucet water lines and within 30"

or less of a standard grounded outlet.

While holding tank in place on

the spot selected for installation,

use a pencil to mark locations for

2 hanging screws.

Property Damage: Tank must be locatedwithin 16" of

faucet andwithin 30" or less of a standardgrounded

outlet. DO NOT extendplumbingor electrical lines.

Tank must be

mountedlevel

to ensure

proper operation.

Mount tank vertically in an area that

allows clearance on the underside of the

tank for drainage, if necessary.

DO NOT over tighten screws.

Pre-drill 1/8"pilot holes at marks.

Turn screws into pre-drilled holes,

leaving 1/4"exposed.

Hang the tank on the screws.

Tighten the screws with only

1/2 turn clockwise.

BScrews provided are for use in wood

studs or cabinets only. Use wall anchors

(not supplied) for installation into drywall.

Leave 1/4"for

hanging tank.

Tank A

Without depressing the gray button,

place the snap-connect fitting at

the end of the blue or copper 1/4"

tube onto the left fitting on the tank,

pushing until it clicks into place. (1)

Tank B

Insert blue 1/4"tube into quick-

connect fitting at left. (1)

Both Tanks

Slip the flexible white 7/16"tube

over barbed steel fitting and slide

down approximately 1/2". (2)

Slip the clear 5/16"tube over the

smooth plastic fitting and slide down

approximately 1/2". (3)

Check for pinched or crimped tubes.

Property Damage: Pinchedor blockedwater lines

may cause damage to the dispenser tank.

Hose clamps are not needed for any

of the connections.

Property Damage: Check to make sure

tubesare connectedproperly andare

pusheddown asfar aspossible.

(1) (2) (3)

(1) (3) (2)

Tank A

Tank B

MOUNTING THE TANK

CONNECTING FAUCET TO TANK

Property Damage: Do not extendthe copper

linesfarther than the 16" provided.

Personal Injury: Do not locate filter above an outlet or other

electrical device. Install headandbracket so that connec-

tionsrequire no stretching, kinkingor pinchingof tubing.

It is normal for approximately 2 oz. of water to

discharge when filter is removed.

Property Damage: Tube runsneedto form to the cabinet’s

contoursto allow storage space with no sharp bends. Tubes

needclean, perpendicular, burr-free cutsto ensure a true fit.

Determine length of tubing required,

then cut to length making sure the cut

is perpendicular and burr-free.

Insert a white 3/8"tube into inlet side

of filter head until it stops.

Press in again to ensure a secure fit.

Insert the other white 3/8"tube

into outlet side of filter head

until it stops. Press in again to

ensure a secure fit.

Mark hole locations for filter head

and bracket in a spot that allows

for filter replacement.

Drill 1/8"starter holes and attach racket to

wall with wood screws, turning until snug.

Remove red filter cap, insert filter

cartridge into filter head and twist

clockwise until “LOCK” arrow on the

filter aligns with arrow on bracket.

To redirect filter replacement water

discharge, place 6"clear tube over

vent hole on the left side of filter head.

Note: 3/8"fitting is required to make

connection to water supply.

Connect remaining white 3/8"tube to

incoming water supply line.

(See Step 6.)

CInsert the copper tube(s) from the

dispenser into the 3/8"to 1/4"

quick-connect fitting.

Connect the white 3/8"tube

from the right outlet on the filter

head into the quick-connect fitting until

it stops. Press in again to ensure a

secure fit.

from water

supply line to dispenser

To remove tube(s) or plug from quick-connector,

depress the release ring and gently pull away.

Discharge tube

From water

supply line To dispenser

From filter or

water supply line

From filter or

water supply line

Plug

5INSTALLING FILTRATION SYSTEM

Hot & cool models Hot only models

Screws provided are for use in wood

studs or cabinets only. Use wall anchors

(not supplied) for installation into drywall.

Scalding Hazard: The faucet dispensesnear-boiling

(212ºF) water which can instantly cause scalds or

burns. Use care when operatingthisappliance.

Property Damage: Join remainingtube

to coldwater supply only.

Turn on the cold water supply.

Depress the dispenser’s HOT handle

and hold it until water flows from the

spout (approximately 1 to 2 minutes).

Run the water for at least 2 minutes

to flush lines (both the hot and cold

handles independently if applicable).



Check all connections to ensure they are

tight

and that there are no leaks.



Plug in instant hot water tank.

Water will be cold at first.

Allow 12-15 minutes for water to reach

target temperature.

Gurgling or hissing is normal during the

initial heating cycle.

Brass Nut

Ferrule

Brass Insert

Plastic

tube



Install a T-fitting (not included)

onto the cold water supply line.



Install dedicated water control valve

with 3/8"compression fitting.



At the end of the white 3/8"tube from the

filter or quick-connector, slide the supplied

brass nut and ferrule over the tube and

then push in the brass tube insert.



Insert the white 3/8"tube into the 3/8"

compression fitting and tighten.

Property Damage: A standardgroundedoutlet within

30" of the dispenser isrequiredunder the sink. Do

not use an extension cordset with the dispenser.

If the water coming from the faucet is not hot 15 minutes after the unit

has been plugged in – or for other issues related to the operation of your

instant hot water dispenser – refer to the “Troubleshooting” section on Page 14.

FINAL WATER CONNECTION



At tank top, depress release ring or gray

release tab into quick-connect fitting

securing blue or copper 1/4"tube and

gently pull line off tank fitting. Pull white

7/16"tube and clear 5/16"tube off fittings.



If not already equipped, the included

snap-connect fitting must be installed.



To install snap-connect fitting, unscrew

brass mounting nut and remove snap-

connect fitting, brass ferrule and nut.

Slide brass nut and plastic ferrule

onto the 1/4"blue or copper tube

running from the faucet.

Insert blue or copper tube into snap-

connect fitting and tighten brass nut

with a wrench, 1 to 2 turns clockwise.

You may elect to use existing tank

mounting bracket.

Refer to Page 7, Steps 3-4 for

complete installation instructions.

ADetermine if your existing tank is A, gray

plastic shell, or B, white metal shell.

At tank top, depress gray release tab

(if A) or release ring (if B) into quick-

connect fitting securing blue or

copper 1/4"tube and gently pull line

out of ﬁtting. Pull white 7/16"tube

and clear 5/16"tube off fittings.

Remove existing faucet.

Blue Tube

Property Damage:

Do not over tighten brass nut.

Property Damage:

Turn off water & unplug tank.

Property Damage:

Unplug tank before connectingfaucet.

Tank A

The snap-connect fitting will be

attached directly to the tank.

Tank B

Cut off snap-connect fitting at the

end of the blue 1/4"tube. Ensure

that cut is straight and burr free.

Insert blue tube into fitting on tank.

Skip to Step 2 (pages 7-11) for

complete installation instructions.

Property Damage: Do not pinch or break copper

tubing. Do not distort the last 1 inch of tubing.

IF INSTALLING ONLY NEW TANK

Release

Tab

1/4"

blue 7/16"

white

5/16"

clear

Release

Ring

1/4"

blue or

copper

7/16"

white

5/16"

clear

Cut

here

Check

orientation

of ferrule

Make note of

orientation

of ferrule

IF INSTALLING ONLY NEW FAUCET

Tank A

Tank B

Otros manuales para 2200

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Dispensador de agua de InSinkErator

InSinkErator

InSinkErator Hot1 Guía del usuario

InSinkErator

InSinkErator CWT Manual de instalación

InSinkErator

InSinkErator indulge Series Manual de usuario

InSinkErator

InSinkErator Hot1 Manual de usuario

InSinkErator

InSinkErator Water Dispenser Manual de usuario

InSinkErator

InSinkErator Model SST-FLTR Manual de usuario

InSinkErator

InSinkErator Indulge Antique F-HC2200 Manual de usuario

InSinkErator

InSinkErator Indulge Contemporary F-HC1100 Manual de usuario

InSinkErator

InSinkErator Model SST-FLTR Manual de usuario

InSinkErator

InSinkErator Indulge Contemporary F-HC1100 Manual de usuario

InSinkErator

InSinkErator H778 Manual de usuario

InSinkErator

InSinkErator H990 Manual de instalación

InSinkErator

InSinkErator Indulge Modern F-H3300 Manual de usuario

InSinkErator

InSinkErator Indulge Contemporary F-GN1100 Manual de usuario

InSinkErator

InSinkErator Hot1 Manual de instalación

InSinkErator

InSinkErator TranScape View Manual de usuario

InSinkErator

InSinkErator Indulge Tuscan F-HC2215 Manual de usuario

InSinkErator

InSinkErator Indulge Tuscan F-GN2215 Manual de usuario

InSinkErator

InSinkErator HOT100 Guía

InSinkErator

InSinkErator Indulge Antique F-GN2200 Manual de usuario

InSinkErator

InSinkErator F-HC3300C Manual de usuario

InSinkErator

InSinkErator Hot1 Manual de usuario

InSinkErator

InSinkErator Instant Hot Water Dispensers Manual de usuario

InSinkErator

InSinkErator Invite H770-SS Manual de usuario

Manuales populares de Dispensador de agua de otras marcas

Monarch Water

Monarch Water ULTIMATE MINI AQUA HE Manual de usuario

Haier

Haier HLM-109B Manual de usuario

abc

abc Fleck 5600SXT Manual de usuario

GE GXOF18G Instrucciones de funcionamiento

Kenmore

Kenmore 625.385560 UltraFilter 650 Manual de usuario

Innova

Innova CEV+ Guía de inicio rápido

Aries

Aries Hydra DI Manual

GE GNCF02H Manual de usuario

ProFlo

ProFlo PFB Series Manual de usuario

Hydrotech

Hydrotech 89DF HIM Manual de usuario

A.O. Smith

A.O. Smith FREZYA 300S Manual de usuario

Frakco

Frakco Travelsoft RV 2400HD Manual de usuario

GE GXSF30V Instrucciones de funcionamiento

Avanti

Avanti WD31EC Manual de usuario

Avanti

Avanti WD360 Manual de usuario

BRIO

BRIO CLCTTL520 Guía del usuario

3M HCD-1 Manual de usuario

Elkay

Elkay EFHFA8_2CJO Manual de instalación