NZW1201 | Door/Temperature Sensor
Page 5
www.inovelli.com/nzw1201-setup contact@inovelli.com
For written/video instructions, please visit:
www.inovelli.com/nzw1201-setup/smartthings/device-handler-installation
Or, follow below -- again, hopefully by the time this is released, we won’t have to worry about installing anything!
Start by opening two tabs on your computer.
The first tab will be: https://graph.api.smartthings.com
The second tab will be: http://bit.ly/2zA6VWJ (sorry, long URL -- it’s a GitHub link)
Go Go to the first tab (SmartThings IDE) and follow these directions:
Click on the green login button (top right)
If you have an account, please login -- if not, please sign up (it’s free) and use the same login as your SmartThings phone app
Once logged in, click on, “My Locations” (top left of the screen) -- you should see the HUB’s location there
Click on your HUB’s location underneath where it says, “Name” -- you may be prompted to login again -- if so, please login
Now we’re going to install the device handler:
First click on, “My Device Handlers” located at the top, in the middle of the screen
Click the green but Click the green button titled, “Create New Device Handler”
Click on, “From Code”
SWITCH TO TAB #2 (GitHub) and copy all 295 lines of code
SWITCH BACK TO TAB #1 (IDE) and paste the code in the white space
After you’ve pasted the code, click, “Create”
Then click, “Publish” and then, “For Me”
Finally, we’re going to change the device type and we’ll be done -- almost there!
Click on, “ Click on, “My Devices” (top of the screen -- TAB #1 - IDE)
Find the, “Z-Wave Door/W indow Sensor” you installed and click on it
Click on, “Edit” at the bottom
Click on the drop down menu under, “Type” (about halfway down) and select,
“Inovelli Door/Window Sensor”
Click, “Update” and you’re done!
◄ STEP 5 - ADDING THE DEVICE HANDLER ►
TO USE THE TEMPERATURE FEATURE A DEVICE HANDLER IS REQUIRED
◄ STEP 4 ►
RUN A Z-WAVE REFRESH TO UPDATE YOUR MESH NETWORK WITH YOUR NEW PLUG
Now we’ll start the inclusion process for your NZW1201 Door/Window + Temperature Sensor
Open up your SmartThings app and click on the, “My Home” tab followed by the, “Things” tab
Scroll to the bottom and click on, “Add a Thing”
Insert the battery into your NZW1201 and auto-inclusion will activate. You will have 30 seconds before it times out. If it
does time out, the backup method to pair/include the device is to press the manual button (B) 3 times within 1 second.
You should now see that your device is detected (it should say, “Z-Wave Door/W indow Sensor”)
H However, if your device says, “Inovelli Door/Window Sensor” then you can skip Step 5 (we are working with ST to
publish our handler so that it will automatically show up when you pair).
After your device is detected, press, “Save” (or if you’d like to rename your device, please do so and click, “Save”)
Once you click, “Save” a pop-up will appear asking you to, “Confirm Paired Devices” -- Click, “OK”
Now, you should be back at the, “My Home” screen and you should be able to see your switch!
AGAIN: If you have issues with pairing/including, please move as close as possible to the HUB and try again -- you can move to
yyour final location when complete
◄ STEP 3 ►
ADDING (INCLUDING) TO THE NETW ORK & COMPLETING THE SETUP PROCESS
Materials Needed: Device Handler*, Cell Phone/Tablet,and a SmartThings HUB (V1 or V2)
Locate a door/window/cabinet (max distance = 3/4”) and within the recommended distance (Pages 2-3) from your HUB/Gateway.
Walls, furniture, and other obstructions may affect the communication between the sensor and your HUB/Gateway, so please
keep this in mind.
◄ STEPS 1 & 2 ►
GATHER YOUR MATERIALS, FIND AN APPROPRIATE OUTLET, AND PLUG IN LAMPS OR APPLIANCES
