Innotech TEMP Manual de usuario

DE – ACHTUNG: Die Verwendung des Innotech-Produktes ist erst zulässig nachdem

die Gebrauchsanleitung in der jeweiligen Landessprache gelesen wurde.

EN – ATTENTION: Use of the Innotech product is only permitted after the instruction

manual has been read in the respective national language.

IT – ATTENZIONE: L’utilizzo del prodotto Innotech è permesso solo previa lettura

del manuale di istruzioni nella lingua del paese corrispondente.

FR – ATTENTION : L’utilisation du produit Innotech n’est autorisée qu’après

la lecture du mode d’emploi correspondant dans la langue du pays.

NL – ATTENTIE: Het gebruik van dit Innotech product is pas toegestaan, nadat

degebruikshandleidingindetaalvanhetbetreendelandgelezenwerd.

SV – O B S : Denna Innotech-produkt får inte användas, förrän bruksanvisningen

på respektive lands språk har lästs igenom.

DK – GIV AGT: Det er først tilladt at anvende Innotech-produktet, før end brugsvej-

ledningen på det pågældende lands sprog er læst.

ES – ATENCIÓN: El uso del producto Innotech sólo está permitido después de que

se hayan leído las instrucciones de uso en el idioma del respectivo país.

PT – ATENÇÃO: O uso do produto Innotech apenas é permitido depois de ter lido as

instruções de uso na respectiva língua nacional.

PL – UWAGA: korzystanie z produktu Innotech jest jedynie dozwolone po przeczy-

taniupodręcznikawjęzykunarodowym.

RO – ATENŢIE:UtilizareaprodusuluiInnotechesteautorizatăabiadupăceaufost

cititeinstrucţiunileoriginaledeutilizareînlimbaţăriirespective.

SL – POZOR: Uporaba izdelka Innotech je dovoljena šele po tem, ko navodila

preberete v svojem jeziku.

CZ – POZOR:PrácesvýrobkemInnotechjepovolenaažpoprostudovánínávodu

kpoužitívpříslušnémjazycedanéhostátu.

SK – POZOR:PoužívanievýrobkuInnotechjepovolenéažpotom,keďstesi

prečítalinávodnaobsluhuvjazykupríslušnejkrajiny.

HU – FIGYELEM: Az Innotech termékek használata csak az után engedélyezett,

miután saját nyelvén elolvasta a használati utasítást.

TR - DİKKAT: INNOTECHürünününkullanımınaancakilgiliülkenindilindesunulmuş

olankullanımkılavuzununtamamenokunmasındanveanlaşılmasındansonraizinverilir.

TEMP

Instruction manual

2TEMP / 200122 / www.innotech.at

Prior to use, the following safety instructions and the current state of the art

must be taken into consideration.

-Keeptheseinstructionsforinstallationandusewiththeproductandcarefullyll

out the acceptance log, the test sheet and the test log.

- Completely read the instruction manual.

- Understand and accept the possibilities and restrictions of the protective equip-

ment as well as the risks associated with its use.

- TEMP should only be installed by specialised/competent experts familiar with

the safety system and in compliance with the current state of the art.

- You must be familiar with these instructions, as well as with the local safety

regulations as a prerequisite for installing and using the system. You must also

bephysicallyandmentallytandtrainedintheuseofPPE(PersonalProtective

Equipment).

-Medicalconditions(cardiovascularproblems,intakeofmedicines,alcohol)can

aectthesafetyoftheuserwhenworkinginhighplaces.

-Adheretotherespectiveaccidentpreventionregulations(e.g.workingonroofs)

wheninstalling/usingtherestraintsystem(andwhenascendingto,entering,

and descending from the roof).

-Measures(emergencyplan)mustbespeciedforfastrescuepriortoinstalling/

using the fall prevention system. Attention: after a fall, a longer period of suspen-

sion in personal protective equipment can cause severe injuries or even death

(suspensiontrauma).

- Before starting the work, you must ensure that no objects can fall to the ground

fromtheworksite.Theareabelowtheworksite(sidewalk,etc.)mustbekept

clear.

-Theinstallersmustensurethatthegroundissuitedforxingtheanchorage

device. If in doubt consult a structural engineer.

- If uncertainties arise during installation/use it is imperative that you contact

themanufacturer(www.innotech.at).

- Ensure that stainless steel does not come into any contact with swarf or steel

tools, as this may lead to corrosion.

- You should plan, install and use the restraint system in such a way that no one

can fall over the edge if the personal protective equipment is used properly.

(Seeplanningdocumentsatwww.innotech.at)

1SAFETY INSTRUCTIONS

TEMP / 200122 / www.innotech.at

- When fastening the TEMP, always use a carabiner or INNOTECH travelling eye-

bolt and wear personal protective equipment in accordance with the information

contained in this instruction manual.

- For horizontal use, only those fasteners may be used that are suited for this

purposeandhavebeentestedfortherespectiveedges(sharpedges,sheetwith

trapezoidal corrugations, steel girder, concrete, etc.).

Attention: avoid pendulum fall!

- Fall arrest devices may only be used if approved for horizontal lifeline systems

by the manufacturers of these fall arrest devices.

- Make absolutely sure that the restraint system cannot be endangered by

sharp edges.

-Thereisahazardwhencombiningindividualelementsofthespeciedunits,since

the safe function of one of the elements can be impaired through the combination.

(Followthespecicinstructionsprovidedwitheachelement!)Incorrectapplica-

tions can result in severe or fatal injuries.

- After a fall and the resulting strain, you must stop using the restraint system and

haveitcheckedbyanexpert(componentparts,fasteningtothesubstrate,etc.).

- TEMP was developed for personal safety and may not be used for other purposes.

Neverattachundenedloadstotherestraintsystem.

- Do not use restraint systems if wind speeds exceed normal parameters.

- Do not make any changes to the approved anchorage device.

- If you provide the restraint system to external contractors, the familiarity with

theinstructionsforinstallationandusemustbeconrmedinwriting.

- Each person active in the areas where there is danger of falling is responsible for

ensuring that the connection to the anchorage system is kept as short as possible

to prevent the possibility of a fall.

A product that does no longer appear to be safe must no longer be used and

must be replaced immediately!

1SAFETY INSTRUCTIONS

4TEMP / 200122 / www.innotech.at

PRIOR TO EACH USE THE USER MUST INSPECT:

- Before use, you must inspect the entire restraint system for obvious defects

(forinstance,reliableoperationofbucklesandratchets;loosescrews,deforma-

tion,abrasion,corrosion;beltsandseamsforweathering,fray,burnmarks,

chafe marks, cracks, cuts or other damage, etc.)

- The steel cable loops of the end locks: Ø = 220 mm

- Check the cable sag when the system is under tension.

(Re-tightenasnecessary:–seesection13“Tighteningthesystem”)

- In addition, use the acceptance log, test sheet and test log to verify that

the protective equipment is suitable for the application.

If there are any doubts concerning the reliable operation of the restraint system, it must

nolongerbeusedandcheckedbyanexpert(writtendocumentation).

ANNUAL INSPECTION: (=sections16/17)

- The complete safety device must be subjected to an inspection by a competent/

specialised expert who is familiar with the restraint system. Depending on the

intensity of use and environment it may be necessary to shorten the inspection

intervals. The inspection must be documented on the test sheet, which must be

stored along with the protective equipment.

ATTENTION! STOP USING THE EQUIPMENT IF:

- Damage or wear to its components is obvious.

- Stress has occurred due to falling.

- Defects have been detected during regular inspections.

- The service life has elapsed.

-Theproductidenticationisnolongerlegible.

Retire the equipment if a visual inspection performed by the owner or a competent/

specialisedexpertrevealeddecienciesorthePPEhasexpired.Whenyouretirethe

equipment, you can be certain that it will not be used again in future applications.

2INSPECTION/SERVICE LIFE

TEMP / 200122 / www.innotech.at

The service life of the TEMP depends on the respective use and cannot be generally

denedduetodierentfrequenciesofuse,useconditions,careandstorage.

When used in compliance with the use guidelines and inspected annually by a competent/

specialised expert, the device has a service life of up to 10 years dating from the year

ofproduction(=markedontheharnessstrap).

Under normal use conditions there is a two year warranty on all components against

manufacturing defects. However, if the system is used in particularly corrosive atmos-

pheres, this period can be shortened.

Ifthereisstrain(afall)thewarrantyclaimisvoidforthosecomponentsthathavebeen

designed to absorb energy, or that may possibly be deformed and, therefore, must

be replaced. Attention: INNOTECH does not assume any warranty in case of improper

installation.

Store the restraint system in a suitable protective sheath to protect it from UV radiation,

chemicals,moisture,sourcesofheatandotherenvironmentalinuences.

IF NECESSARY:

Clean the harness strap using lukewarm water and mild soap, rinse it with clear water

andletitdryintheair(neverdryitinthelaundrydryeroraboveasourceofheat).

3SERVICE LIFE

4WARRANTY

5STORAGE/CARE

6TEMP / 200122 / www.innotech.at

uENDS-10

uSZH-10

6DIMENSIONS/MATERIAL

-End lock ENDS-10:

anodised aluminium,

AISI 304 stainless steel,

galvanised steel

-Polyester harness strap:

50x4,000mmwithpowder-coatedsteelendtting

and protective polyester sleeve with smooth

PVC coating Ø 35 x 2,000 mm

-Ratchet:

50mm,18teeth,5,000daN;

composed of galvanised steel and plastic handle

-SZH-10 intermediate bracket:

AISI 304 stainless steel and nickel-plated steel

-Polyester harness strap:

50 x 2,500 mm

including sewn-in ratchet:

50mm,18teeth,5,000daN;

composed of galvanised steel and plastic handle

uAIO SEIL-30

-Stainless steel cable:

AISI316stainlesssteel,diameter:Ø8mm(7x7)

breakingload:37kN

51,4114,5

49,5

31,5

51,4114,5

49,5

31,5

51,4114,5

49,5

31,5

115

58,5

0,5

115

58,5

0,5

TEMP / 200122 / www.innotech.at

7STANDARDS

8ANCHORAGE SUBSTRATE

9SIGNS & MARKINGS

INNOTECHTEMPhasbeentestedandcertiedinaccordancewith

EN 795:2012 TYPE B and EN 795:2012 TYPE C.

THE NOTIFIED AUTHORITY PARTICIPATING IN THE TYPE TEST:

DEKRATestingandCerticationGmbH,Dinnendahlstr.9,44809Bochum,C0158

ThetypetestwasperformedinaccordancewithEN795:2012.

It is best to install the horizontal lifeline system above the user.

The basic prerequisite is a static, carrying substructure.

The carrying structure used to fasten the TEMP must have great inherent stability

and a minimum strength of 22 kN.

Name or logo of the manufacturer/reseller: INNOTECH

Type designation: TEMPENDS-10/TEMPSZH-10

Batch number of the reseller: 20xx/xx

Year of production: 20xx

Manufacturer’s ID no: P-xxxxx

Length: 4 m/2.5 m

Signs stating that the instructions specied

in the manual must be followed:

HARNESS STRAPS 

Year of production

Length: 4 m

Year of production

Length: 2.5 m

8TEMP / 200122 / www.innotech.at

EN 795:2012 TYP B

EN 795:2012 TYP C

TEMP-ENDS-10

13-03-10-Aufkleber-DE-A

SEILAUSLENKUNG MAX. 2,5

FALLDÄMPFER JA

0158

max.

JJJJ-..-...

Max. cable deection 2,5 m

Fall breaker YES

Name or logo of the manufacturer/reseller: INNOTECH

Type designation: TEMP

Numbers of the applicable standards: EN795:2012TYPEB

  EN795:2012TYPEC

Maximum cable deection after a fall: 2.5 m

Fall breakers required: YES

DEKRA Testing and Certication GmbH:C0158

Year of manufacture and manufacturer’s serial number: 20xx - xx

Maximum number of people who will be secured: 4(including1personfor

  rst-aidadministration)

Signs stating that the instructions specied

in the manual must be followed:

uEND LOCKS (= SYSTEM RATING PLATE)

The mobile horizontal lifeline system is suitable for temporary installation on various

base structures. Ideal for construction sites/building constructions of all kinds.

(Steel,facade,hallandbridgeconstruction,etc.)

Approved as a temporary horizontal lifeline system for 4 people(including1person

forrst-aidadministration)alongahorizontalandstraightspanwithapitch ranging

from 0° to a maximum of 15°.

SuitableforthefollowingfallprotectionsystemsinaccordancewithEN363:2008

• Restraint systems

• Workplace positioning systems

• Fall arrest systems

• Rescue systems

Safeapplicationrequiresthatyouobservethecorrespondingspecicationsprovided

by the PPE manufacturers.

For safety reasons, we recommend that you always use fall arrest systems as restraint

systems!TEMPisnotsuitableforabseilingwork(ropeaccesssystems(EN363:2008)).

9SIGNS & MARKINGS

10 USE INSTRUCTIONS

TEMP / 200122 / www.innotech.at

Theusermustbecapableofselectingandproperlyhandlingthe“PersonalProtective

Equipment(PPE)againstfallsfromaheight”indueconsiderationofEN363:2008!

Theappropriate“PersonalProtectiveEquipment(PPE)againstfallsfromaheight”is

connected to the stainless steel cable of the TEMP anchorage device, which is spanned

horizontally,followingtheinstructionsofthePPE’smanufacturer(seeinstruction

manual for the PPE).

(E.g:EN353-2orEN354+EN355,etc.-->werecommendthatyouusea“Y”rope

or INNOTECH travelling eyebolt in connection with systems that include an intermediate

bracket.)

Attention!TheTEMPanchoragedeviceisttedwithshockabsorbersinordertoabsorb

theforcesgeneratedduringafall(harnessstraps+cableloopsoftheendlocks).Inthe

event of a fall, the stainless steel cable extends by contracting the cable loops, thereby,

absorbing the fall. This is why you need to make sure that, while using the fall arrest

system, you always leave enough free space below the user to prevent him from hitting

the ground in the event of a fall.

The minimum free space necessary between the fall point and the ground is

calculated as follows:

Free-fall height1(height of the unchecked fall until the PPE stops the fall)

+ Existingcablesagofthesystemafterinstallation

(checkduringuseandre-tightenasnecessary!)

+ Max.cabledeectionafterafallaccordingtotable(max.2.5m)

+ Manufacturer’sinstructionsofthePPEusedtopreventfallsfromaheight

(e.g.:max.brakingdistanceofthefallarrestdeviceasspeciedbythemanufacturer,etc.)

+ Shiftofthefall-arresteyeletattachedtothesafetyharnessinaccordancewithEN361

(approx.1.0m)

+ Safetymargin:1.0m

Length without intermediate bracket: Max.cabledeectionafterafall:(4people)

6m 1.1m

12m 1.7m

15m 2.0 m

20 m 2.5 m

1... can be avoided if positioned and used in the proper manner!

ThedeviceisattachedtothesystemonlybymeansoftheØ8mmstainlesssteelcablewhichisspanned

horizontally. Fastening the device to the harness strap, ratchet, etc. represents a safety risk and is prohibited!

INCORRECT APPLICATIONS 

10 USE INSTRUCTIONS



10 TEMP / 200122 / www.innotech.at

COMPONENTS TEMP SZH-10:

When storing the device, always secure the bolt at the end lock using the split pin!

COMPONENTS TEMP ENDS-10:

11 COMPONENTS

Tabla de contenidos

Otros manuales de Accesorios de Innotech

Innotech

Innotech innTOUCH Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario