Ink Bird PLUS Manual de usuario

U S E R M A N U A L

INKBIRDPLUS BLUETOOTH

SMART DOOR LOCK

CONTENTS

01 Product Introduction 1

02 Package Introduction & Screws 2-3

06 Technical Parameters 33

07 FCC Requirement 34

05 Device Operation

How to Finish the Settings without APP

1. How to Add Fingerprints, Passwords, and IC Cards

2. Optional Functions

03 Installation Manual

1. Check Door Dimensions

2. Installation Steps

4-8

04 APP Operation

1. Download and Install the INKBIRD App

2. How to Connect to INKBIRD App

3. How to Add Fingerprints, Passwords, and IC Cards

4. Optional functions

9-10

8-9

11-19

20-31

Front Panel Back Panel

Product Introduction

①Fingerprint Sensor

②Keyboard/Card Sensor

③Close/Return/Doorbell

④Confirm

⑤Type-C USB Port

⑥Keyhole

⑦Battery Groove

⑧Reset Button

⑨Thumb Turn:Manually ON/OFF

⑩Quick Open/Close

Package Introduction

Part Description Quantity

Key

IC Card

Front Panel

3M Sticker

Latch

Wood Screw Set

Strike Plate

Plastic Lock Groove

Mounting Plate

Back Panel

Spare Screw Set

Long & Short Screw Set

Battery Cover

Long Screw Set

Size Reference

Screws

Installation Manual

Smart Door Lock

Door Thickness

Hole : Φ2-1/8"(54mm)

Note: Install and test the lock with the door open

to avoid being locked out.

Scan to Download the Manual

Tools Needed

Screwdriver; Tape Measure; Pencil; Other Chiseling Tools; Size

Reference Card.

1. Check Door Dimensions

1) Backset Determination

Backset is a distance from door edge to center of hole on door face.

Backset can be 2-3/8"or 2-3/4"(60mm or 70mm).

2. Installation Steps

1) Adjust Latch Length

Insert the latch and ensure it is parallel to the door face.

2) Hole Diameter

Using the marks as guide to drill holes

Φ3/8"(10mm) Fasten Smart door lock(Optional)

Hole : Φ2-1/8"(54mm)

3) Door Thickness

The door thickness between 1-3/8" and 2- 11/64" (35mm-55mm) are

all suitable for the keypad deadbolt handle set.

Note: When performing this operation, please take protective

measures and be careful of the metal edge not to injure yourself.

Hold the right part of the lock tongue with your right hand and turn

the left iron piece counterclockwise (about 15 degrees) with your left

hand.

When the rectangular position of the 2-3/8” (60mm) tick mark

changes from convex to concave (as shown), slowly extend the

locking latch, and then turn clockwise the inside of the locking latch

back to the rectangular

position of2-3/4” (70mm) scale.

2) Install Latch

Note: Need to keep this way up when inserting the latch.

A.Mark the outline of the plate, then take out the latch.

B.Chisel 1mm-2mm deep along the outline to allow the plate to

be aligned with the door edge.

C.Insert the latch into the door, use 2 F :Wood Screw Set to

secure latch.

3) Install Strike Plate

Torque blade

Optional

A.Identify the center of the plate: Close the door to lay the latch bolt

against the door frame. Mark the outline of the plate onto the

doorjamb.

B.Drill 25mm deep at the intersection of the horizontal and vertical

lines of the plate. Chisel 1mm-2mm deep along the strike plate

outline to allow the strike plate to be aligned with the door frame.

C.Insert the plastic lock groove and the strike plate into the

doorjamb and tighten with F :Wood Screw Set.

4) Install Front Panel

A.If you want to secure the door lock, please stick the 3M stickers on

the front panel. (Optional)

B.Let the cable and the [torque blade] go through the holes on the

latch, as in the picture.

C.IMPORTANT: Latch must be in unlock position, and place the

cable under the latch.Make sure the [torque blade] is in horizontal

state.

45mm

55mm

D.Pass the Cable and the [torque blade] to mounting plate as in

the picture.

E.Use the 2 long screws to attach the mounting plate to the front

panel.

Notes:

The long screw set has two sizes of screws, one for door

thickness 1-3/4" (45mm) M Long & Short Screw Set and the

longest screws ﬁt for2. 17" (55mm) JLong Screw Set .

5) Install Back Panel

A.Remove the battery cover and back cover (use the sharp object

to push the back cover up first)

B.Connect the cable and ensure a tight cable connection.

C.Rotate the Thumb turn in a vertical position and insert the [torque

blade] into the interior assembly lock switch.

D.Use a short screw to tighten the inner battery groove on the back

panel, then use a long screw to attach the back panel to the door

M: Long & Short Screw Set.

E.After installing the back panel, rotate the thumb turn to test if it

works with the latch.

If that doesn't work, take out the back panel and make sure the

[torque blade] is in horizontal state and try to install it again until it

works with the latch.

APP Operation

6) Insert Battery and Install Back Battery Cover

A.While the door is open and unlocked, insert 4 (AA) 1.5V Alkaline

batteries into the back panel.

B.Press and hold the reset button on the back panel.

C.Keep holding the reset button until you hear “Factory reset

successfully ”.

The lock will automatically go into the locked position. This is to let

the smart lock memorize the orientation of the door.

D. If the door ca

Note:

1. Your iOS devices must be running iOS 11 or above to download

the app smoothly.

2. Your Android devices must be running Android 7.1 or above to

download the app smoothly.

Preparations

1) Complete the hardware installation.

2) Install 4 AAA batteries.

(After the first hardware installation, be sure to restore the factory

settings) Press and hold the reset button in the lower right corner

of the battery compartment for 5 seconds.

Note:

Wave up the keyboard, please touch and hold the keyboard for2

seconds.

If the unlock fails 10 times, the system will automatically lock for3

minutes.

1. Download and Install the INKBIRD App

1) Search "INKBIRD" in App store or Google Play, or scan the

following QR code to download and install the APP, or update it to

the latest version.

Notes:

A.Alkaline batteries are recommended to stabilize the power

supply. If you don't use alkaline, battery performance will be

reduced greatly.

B.All settings will be saved even if all batteries are completely

discharged. Having a Type-C USB port can power the lock and

activate the keyboard.

Tabla de contenidos

Manuales populares de Cerradura de puerta de otras marcas

Assa Abloy

Assa Abloy effeff 827A-IP Manual de usuario

We.lock

We.lock SECBNEBL51 Manual de usuario

Iseo

Iseo MA1A Manual de usuario

ID Lock

ID Lock 150 Manual de usuario

Lockly

Lockly ACCESS TOUCH PRO Manual de usuario

iLoq

iLoq G50S Manual de usuario

SDC

SDC Z7835 Manual de usuario

ilco

ilco 452 Manual de usuario

Samsung

Samsung shs-h705 Manual de usuario

TRU-BOLT

TRU-BOLT 08102017 Manual de usuario

CDVI

CDVI 500-LADJ Manual de usuario

Igloohome

Igloohome Deadbolt 2S Metal Grey Instrucciones de instalación y mantenimiento

eSSL

eSSL FL-300 Manual de usuario

JAKO

JAKO JKBTNX4 Manual de usuario

Dorma

Dorma MUNDUS PREMIUM GK 50 Guía del usuario

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manual de usuario

Yale

Yale MORTISE 8800 SERIES Manual de usuario

Siegenia

Siegenia KFV AS3500 Manual de usuario