Ingersoll-Rand QX Series Manual de usuario

TL-VP1T-UIM

Edition 1

October 2021

Save These Instructions

QX Connect Series

User Manual E

EN-1 TL-VP1T-UIM_ed1

Intended Use:

This manual provides instruction for programming the parameters of QX Connect Series handheld tools.

How to Program

• Program via ICS Software: A Windows-based tool that can be installed on a computer, with supplied USB cable.

• Program via Back Cap Tool Display: The information contained in this document is a guide for how to program the

handheld tool.

Back Cap Identication

Display Screen

Status Led

Enter

Yellow Green Red

Escape

Left

Down

Reverse

(Angle Tools Only)

Right

Symbol Function Table (Status LEDs - Blink rate 1/4 seconds per box except paired indication

once per 12 seconds)

Escape / Exit OPaired with INSIGHTqcx or Multi-Tool Controller (MTC)

Paired with INSIGHT Connect App

Paired with MTC or INSIGHTqcx and ETS Mode

Paired with INSIGHT Connect App and ETS Mode

Ergonomic Tightening System (ETS) Mode

Preventive Maintenance (PM) Alarms

Firmware Uploading

Firmware Upgrading (Do not power o)

OB OB OB

OPPP

PPP

Enter / Edit

DOWN

RIGHT

LEFT

Status LEDs

The tool contains 4 Status LED’s on the display module. Three located above and one below the screen.

Orange (O) -- See Table.

Blue (B) -- See Table.

Purple (P) -- See Table.

Green -- The last tightening cycle ended between the high and low limits.

Yellow -- The last tightening cycle ended below the low limit.

Red -- The last tightening cycle ended above the high limit.

Note: Red and Yellow functionality may be swapped using Invert LEDs setting in INSIGHT Connect App, INSIGHTqcx and

ICS.

TL-VP1T-UIM_ed1 EN-2

1. Overview of Menu Screens

Direct/ETS Select

Editable Target Screen

Run Screen

Fault Screen

Mode Selection Screen

Torque or Angle

Selection Screen

Go to INSIGHT Connect App Pairing SCREEN

Press "DOWN"

Power up QX Connect Series tool

or "ENTER"

First Use Screen Change Selected

Item

FIRST USE SCREEN BASIC MODE SCREENS

NORMAL MODE SCREENS

PSet or Job Selection

Screen

Torque Target or Torque

Range Screen

Angle Target or Angle

Range Screen

Run Result Screen

Cycle Count Screen

Fault Screen

Wireless Status Screen

Mode Selection Screen

Password

Screen

Password

Screen

Wireless

Selection

Screen

Go to Debug

Screens

Go to MTC Pairing SCREEN

Go to PSet Normal Mode

Go to Basic Mode

Unit of Torque

Direction: Clockwise or

Counter-clockwise

Strategy: Angle or Torque

Target Angle (Angle Strategy) or

Target Torque (Torque Strategy)

Torque High

Password

Screen

Torque Low

Angle High

Angle Low

Torque Threshold

Free Speed

Shiftdown Torque

Shiftdown Speed

Gang Count

Save/Cancel Changes

Power up QX Connect Series tool

EN-3 TL-VP1T-UIM_ed1

2. Getting Started

2.1 Initial Screen

Note: Displayed at the time of initial setup or after a factory reset.

Select how to interface with the tool. The options are the INSIGHT Connect App via Bluetooth, INSIGHTqcx controller via

wireless, PCM or Standalone (normal mode), or Standalone (basic mode). Press the and arrow buttons to make the

selection and then the button.

2.1.1 INSIGHT Connect App

Enable Bluetooth pairing on the INSIGHT Connect App to connect to the tool and follow the directions on the App.

When the 6 digit code appears, conrm it matches with code displayed on the mobile device and press button.

2.1.2 INSIGHTqcx

Set the INSIGHTqcx controller into pairing mode to pair with the tool.

2.1.3 PCM/Standalone

Normal Mode - Full Menu Access

• Use ICS to congure the tool wireless settings while communicating with a PCM.

• Use ICS or the tool navigation to setup the fastening settings while using as a standalone tool.

TL-VP1T-UIM_ed1 EN-4

2.1.4 Standalone

Basic Mode - Limited menu for quick setting of torque or angle targets. To enable advance settings, switch to normal

mode.

2.2 Switching between Basic and Normal Modes

To switch between Basic and Normal Mode, press button to edit. Enter the password (default password is 0000). Press

arrow button to get to edit screen and then or arrow button. Press button to select mode.

2.3 Password

The default password set at the factory is 0000. To enable the password, connect to the INSIGHT Connect App,

INSIGHTqcx, or ICS to change password.

To enter password from Back Cap, press button to edit and use arrow buttons to change the values. Press button to

accept.

2.4 Setting the Clock

The tool has a clock that will retain the date/time during battery swaps. For initial setup, connect to the INSIGHT

Connect App, INSIGHTqcx, or ICS. The date/time will be set automatically on connection.

3. Basic Mode

3.1 Setting the Target

Press button to enter Edit mode. Move left or right to underline the digit. Press or arrow button to change the

value. Press button to save the changes.

EN-5 TL-VP1T-UIM_ed1

3.2 Torque or Angle Mode

Press button to enter Edit mode. Move or arrow button to move the arrow. Press button to save the changes.

4. Normal Mode

4.1 PSet

Press button to enter Edit mode. Press or arrow button to change the PSet selection and press button to save

the change. 32 unique programmable PSets are available.

To edit the selected PSet, press arrow button to access the password screen. Enter the password and press arrow

button or just press arrow button if the password is not set.

4.1.1 Target

To edit the Target, press button to enter Edit mode and use the arrow buttons to change the values. Press button to

accept.

4.1.2 Torque High Limit

To edit the Torque High Limit, press button to enter Edit mode and use the arrow buttons to change the values. Press

button to accept.

TL-VP1T-UIM_ed1 EN-6

4.1.3 Torque Low Limit

To edit the Torque Low Limit press button to enter Edit mode and use the arrow buttons to change the values. Press

button to accept.

4.1.4 Angle High Limit

To edit the Angle High Limit, press button to enter Edit mode and use the arrow buttons to change the values. Press

button to accept.

4.1.5 Angle Low Limit

To edit the Angle Low Limit press button to enter Edit mode and use the arrow buttons to change the values. Press

button to accept.

4.1.6 Torque Threshold for Counting Angle

To edit the Torque Threshold for Counting Angle, press button to enter Edit mode and use the arrow buttons to

change the values. Press button to accept.

4.1.7 Free Speed

Programmed Speed is a percentage of the tool's maximum speed. To edit Free Speed, press button to enter Edit

mode and use the arrow buttons to change the values. Press button to accept.

EN-7 TL-VP1T-UIM_ed1

4.1.8 Shift Down Torque

To edit Shift Down Torque, press button to enter Edit mode and use the arrow buttons to change the values. Press

button to accept.

4.1.9 Shift Down Speed

Programmed Speed is a percentage of the tool's maximum speed. To edit Shift Down Speed, press button to enter

Edit mode and use the arrow buttons to change the values. Press button to accept.

4.1.10 Batch Count

Batch count is the number of items to be fastened per group, gang, or set. To edit the Batch Count, press button to

enter Edit mode and use the arrow buttons to change the values. Press button to accept.

4.1.11 Save

Press button to save or button to abort.

Shortcut: Press button from any setup menu page to jump to the save page then press button to save or button

to abort changes.

4.1.12 Drive Mode

Tool supports direct drive and 3 ETS tightening modes (ETS optional). ETS enable QX Connect Series handheld tools are

equipped with a feature to reduce reaction during fastening cycles. The energy required for a specic fastening cycle is

analyzed and transferred into a series of pulses. Refer to General Settings in ICS, INSIGHTqcx, or INSIGHT Connect App to

ENABLE/DISABLE ETS functionality.

1. Ergonomic Mode: The softest and slowest mode with the most number of pulses. Ideal for hard joints or when arm,

wrist and/or tool angles are most dicult.

2. Performance Mode: Best all-purpose setting, provides an average number of pulses. Start in Performance Mode

and adjust accordingly.

3. Productivity Mode: The fastest mode with the least number of pulses. Ideal for soft joints or high production rates.

TL-VP1T-UIM_ed1 EN-8

To change between direct drive and the ETS modes, press button to enter Edit mode and use and arrow buttons.

To change ETS mode, move pointer to ETS position and use and arrow buttons to change the ETS Mode. Press

button to accept.

4.1.13 Torque Units

To edit the torque units, press button to enter Edit mode and use the and arrow buttons to change the value.

Press button to accept.

4.1.14 Fastening Direction

To change between clockwise and counterclockwise, press button to enter Edit mode and use the and arrow

buttons to change the value. Press button to accept.

4.1.15 Control method – Torque / Angle

To change between torque control and angle control, press button to enter Edit mode and use the and arrow

buttons to change the value. Press button to accept.

4.2 Target

The top section is the target value.

The lower left section is the primary low limit.

The lower right section is the primary high limit.

The target and limits will be torque values when using torque control or angle values when using angle control.

EN-9 TL-VP1T-UIM_ed1

4.3 Secondary Limits

The lower left section is the secondary low limit.

The lower right section is the secondary high limit.

The secondary limits will be torque values when using angle control or angle values when using torque control.

4.4 Run Screen

The top section is the result of the last fastening. The value will be either a torque or an angle.

The lower left section provides the Batch Count information in the format CURRENT COUNT/TOTAL BATCH.

The lower right section is current selected PSet.

4.5 Cycle Count

Displays the cycle count since the last reset.

4.6 Fault / Diagnostics

Displays the last fault logged.

4.7 Communications

Otros manuales para QX Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Ingersoll-Rand

Ingersoll-Rand

Ingersoll-Rand 103A Manual de usuario

Ingersoll-Rand

Ingersoll-Rand QS110P4 Guía de configuración

Ingersoll-Rand

Ingersoll-Rand 7LR series Manual de usuario

Ingersoll-Rand

Ingersoll-Rand IQ V20 Cordless Impactool W5000 Series Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 8RSL32 Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 100SQ1-EU Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 500P Guía de configuración

Ingersoll-Rand

Ingersoll-Rand QM5 Series Guía de configuración

Ingersoll-Rand

Ingersoll-Rand QE8 Series Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 180PQ1-EU Manual de usuario

Ingersoll-Rand

Ingersoll-Rand IQV20 W7152 Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 231C series Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 1701 Series Manual de usuario

Ingersoll-Rand

Ingersoll-Rand DE Series Manual de usuario

Ingersoll-Rand

Ingersoll-Rand ES45T Guía de configuración

Ingersoll-Rand

Ingersoll-Rand SERIES EL Manual de usuario

Ingersoll-Rand

Ingersoll-Rand PowerForce PF700 Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 380SQ1-EU Guía de configuración

Ingersoll-Rand

Ingersoll-Rand Q60P3 Guía de configuración

Ingersoll-Rand

Ingersoll-Rand ARO 7165-B-EU Guía de configuración

Ingersoll-Rand

Ingersoll-Rand 2915P1 Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 1107LR Manual de usuario

Ingersoll-Rand

Ingersoll-Rand IR20BV Manual de usuario

Ingersoll-Rand

Ingersoll-Rand IR30VRD Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual