Ingersoll-Rand QX Series Manual de usuario
QX Series Display
User Manual
Save These Instructions
48619852
Edition 3
April 2014
RELEASED 18/Apr/2014
EN-1 48619852_ed3
EN
Purpose of the document:
This document provides details about dierent menu screens, their description and how to edit those screens in display
module, required for the operation of QX Series Hand Tool.
The image Below shows the display of QX Series display module with descriptions of the programming keys.
ESCAPE
LEFT
DOWN
UP
ENTER
RIGHT
Symbol Function
Escape / Exit
Enter / Edit
UP
DOWN
RIGHT
LEFT
RELEASED 18/Apr/2014
48619852_ed3 EN-2
EN
1. Overview of dierent Menu screens
Power up QX Series tool
RUN SCREEN
Press “UP” key.
Number being used.
Always Press “UP” key to
go to next screen.
Press “ENTER” to enter “EDIT” mode.
Password screen
Current fault
Status screen with shunt
cal, wireless strength and
battery level.
Cycle Count
Target Angle, Low
and High screen.
Target Torque Low
and High screen.
RUN SCREEN
Press “UP” key to
increment the value
Press “DOWN” key to
decrement the value.
Press “ENTER” to select
the changed values.
Press“ESC” to undo and
keep the old values.
After display is unlocked
Press “RIGHT” Key.
Press“UP” key to go to
next screen
Save or Ignore changes. If not on
Save screen, use the up or down
key to scroll to the Save screen.
Press "DOWN" key to scroll
on one by one to get
below editable screens.
After display is unlocked
Press "LEFT" key.
Enable / disable RF module.
Press "RIGHT" key to go to
the RUN SCREEN.
RELEASED 18/Apr/2014
EN-3 48619852_ed3
EN
Strategy – Angle or Torque
Direction – Clock wise or anti
clockwise
Unit of Torque
Target Angle (Angle strategy) OR
Target torque (Torque strategy)
Torque High
Torque Low
Angle High
Angle Low
Torque threshold
Free Speed
Shift down torque
Shiftdown Speed
Gang count
Save / ignore the changes
settings
RELEASED 18/Apr/2014
48619852_ed3 EN-4
EN
2. Description of the Display screen in detail
There are three sections in the QX Series display screen, one “PRIMARY” on the top and two “SECONDARY”which are on
left and right bottom of the display.
2.1. Run Screen
Pressing“ENTER”key after switching on the display will show this image.
PRIMARY Section - shows latest peak torque (for a torque strategy) or the latest peak angle (for an angle strategy), with
units.
The SECONDARY LEFT - shows the cycle count or gang count, if gang count is programmed.
The SECONDARY RIGHT - shows the active conguration number.
RELEASED 18/Apr/2014
EN-5 48619852_ed3
EN
2.2. Conguration
Pressing“UP” will advance to next screen.
Screen shows CONFIGURATION setting used in the tool.
NOTE: Only Conguration 1 can be programmed through the display module.
Pressing“ENTER”will enable the “EDIT MODE” (This procedure to enter “EDIT MODE” is same for all settings update).
RELEASED 18/Apr/2014
48619852_ed3 EN-6
EN
“UP” or “DOWN” key can be used to update the conguration. Pressing “ENTER” again will select the modied
conguration.
2.3. Password
The password screen shows whether the display is locked or unlocked. If the display is locked the parameters of the QX
Series Hand tool cannot be edited.
RELEASED 18/Apr/2014
EN-7 48619852_ed3
EN
Password can be changed by entering into “EDIT MODE” and using “UP” or“DOWN” key.
If “1234” is entered on the Password screen, the user may use the left arrow to go to the Tool ID and software version
page.
The Primary Display is the “Tool Location ID”.
Lower Secondary Right is the“Display Firmware” Version.
Lower Secondary Left is the “Motor Controller Firmware” Version.
RELEASED 18/Apr/2014
48619852_ed3 EN-8
EN
Displays Tool time in HH:MM:SS format. Press the Down key to display the tool time in HH:MM:SS format.
Remaining screens are for internal use only to view log location. Press the Down key to display a screen for internal use
only to view log location. Press the Down key again to display a second log screen.
Press the Down key again to return to the Tool ID page. Pressing the right arrow from this page exit back to the Run
screen.
RELEASED 18/Apr/2014
EN-9 48619852_ed3
EN
Press‘ENTER’to enter the‘EDIT’mode. Enter the appropriate password to unlock the tool. Press‘ENTER’to exit the‘EDIT’
mode.
2.3.1. Updating fastening parameters of the QX Series tool
After display is unlocked with a valid password, Pressing “RIGHT” key will advance to following settings that can be
modied as required.
The settings can be modied by entering“EDIT MODE” and using “UP” or “DOWN” key or“RIGHT”or “LEFT” key as
required.
RELEASED 18/Apr/2014
Otros manuales para QX Series
9
Tabla de contenidos
Otros manuales de Monitor de Ingersoll-Rand
