Ingersoll-Rand E688 Series Manual de usuario

48484703

Edition 1

January 2012

Save These Instructions

Product Information

EN Product Information

产品信息

EN Product Information

Air Impact Wrench

E688 series

2 48484703_ed1

48h

PMAX

24h

(Dwg. 47132790)

IR # - NPT IR # - BS inch (mm) NPT IR # IR # IR # cm3

C38341-810 C383D1-810 1/2 (13) 1/2 MSCF44 10P 100-1lb 4

Instruction

使用注意事项

F-R-L unit or equivalent is recommended.

一定要安装三联件或同等功能的过滤器和干燥器。

If an F-R-L is installed, it should be visually inspected regularly to be sure the ler is clean and

that the lubrication oil is at or above the minimum suggested level. the regulator should be set

so that air pressure at the tool inlet does not exceed 120psi.

安装了管路三联件，必须要保持过滤器的清洁，每天放水一次，润滑器的油必须保证不能

低于最低油位，工具进气口的压力不能大于120psi。

If no an F-R-L is installed, lubrication oil should be added at the tool inlet every 8 hours of actual

tool use.

在工具使用时必须每8小时在工具进气口处加一次润滑油。

F-R-L: 三联件（Filter 过滤器，Regulator 调压阀， Lubricator 润滑器）

48484703_ed1 EN-1

Product Safety Information

Intended Use:

These Air Impact Wrenches are designed to remove and install threaded fasteners.

For additional information refer to Air Impact Wrench Product Safety Information Manual

Form 04580916.

Manuals can be downloaded from www.ingersollrandproducts.com

Product Specications

Model Style

Drive Impacts

per min.

Recommended Torque

Range

Type Size Forward

Nm (ft-lb)

Tools running at 90PSI Air Pressure

E688-8 Outside Trigger Square

8” extended 1” 625 271-3100 [3300 MAX]

(200-2300 [2450 MAX])

Tools running at 120PSI Air Pressure

E688-8 Outside Trigger Square

8” extended 1” 740 271-3500 [3800 MAX]

(200-2600 [2800 MAX])

Model

Sound Level dB (A)

(ISO15744)

Vibration (m/s2)

(ISO28927)

† Pressure (Lp) ‡ Power (Lw) Level *K

Tools running at 90PSI Air Pressure

E688-8 105.3 116.3 11.8 2.5

Tools running at 120PSI Air Pressure

E688-8 106.6 117.6 15.9 3.7

† KpA = 3dB measurement uncertainty

‡ KwA = 3dB measurement uncertainty

* K = Vibration measurement uncertainty

Installation and Lubrication

Size air supply line to ensure tool’s maximum operating pressure (PMAX) at tool inlet. Drain

condensate from valve(s) at low point(s) of piping, air lter and compressor tank daily. Install a

properly sized Safety Air Fuse upstream of hose and use an anti-whip device across any hose

coupling without internal shut-o, to prevent hose whipping if a hose fails or coupling

disconnects. See drawing 47132790 and table on page 2. Maintenance frequency is shown in a

circular arrow and dened as h=hours, d=days, and m=months of actual use. Items identied as:

1. Air Filter 6. Thread size

2. Regulator 7. Coupling

3. Lubricator 8. Safety Air Fuse

4. Emergency shut-o valve 9. Oil

5. Hose diameter 10. Grease - during assembly

EN-2 48484703_ed1

Parts and Maintenance

When the life of the tool has expired, it is recommended that the tool be disassembled,

degreased and parts be separated by material so that they can be recycled.

Original instructions are in English. Other languages are a translation of the original instructions.

Tool repair and maintenance should only be carried out by an authorized Service Center.

Refer all communications to the nearest Ingersoll Rand Oce or Distributor.

48484703_ed1 ZH-1

产品安全信息

用途：

这些气动冲击扳手专门用于拆卸和安装螺钉。

更多信息，请参考《冲击扳手产品安全信息手册表04580916》。

手册可从www.ingersollrandproducts.com 下载。

产品规格

型号样式

打击头冲击

每分钟

建议扭矩范围

类型尺寸正向

英尺- 磅 Nm (ft-lb)

在90 PSI气压下运转的工具

E688-8 外压扳机四方 8” 加长 1” 625 271-3100 [3300 MAX]

(200-2300 [2450 MAX])

在120 PSI气压下运转的工具

E688-8 外压扳机四方 8” 加长 1” 740 271-3500 [3800 MAX]

(200-2600 [2800 MAX])

型号

噪音等级 dB (A)

(ISO15744)

震动 (m/s²)

(ISO28927)

† 压力 (Lp) ‡ 功率 (Lw)水平 *K

在90 PSI气压下运转的工具

E688-8 105.3 116.4 11.8 2.5

在120 PSI气压下运转的工具

E688-8 106.6 117.6 15.9 3.7

† KpA = 3dB 测量不确定度 * K = 测量不确定度 (震动)

‡ KwA = 3dB 测量不确定度

安装和润滑

选择合适的供气管以确保在工具入口获得最大的工具操作压力(PMAX)。每天从管道、空气过

滤器和压缩机罐的低位置点排空冷凝水。如果软管出现故障或连接断裂，可在软管上流位

置安装一尺寸合适的空气保险装置，并在软管内部不关断情况下，通过任何软管连接使用

稳固装置来防止软管的摆动。请参阅图47132790 和第二页上的表格。维护频率以圆形箭头

表示为实际使用的 h=小时，d=天数，m=月数。项目定义如下：

1. 空气过滤器 5. 软管直径 9. 机油

2. 调整器 6. 螺纹尺寸 10. 油脂- 装配时使用

3. 加油器 7. 联结

4. 紧急关闭阀 8. 空气保险装置

部件和维护

当工具到达使用寿命后，建议您将工具拆开、去油，并将零件按材质分开，以便回收。

初始说明采用英文。其他语言版本是初始说明的翻译版。

工具维修工作只能由具有授权的维修中心执行。

任何事宜，请垂询当地的 Ingersoll Rand 办事处或经销商。

Notes:

www.ingersollrandproducts.com

Este manual sirve para los siguientes modelos

Otros manuales de Atornillador de impacto de Ingersoll-Rand

Ingersoll-Rand

Ingersoll-Rand 2161 Guía de configuración

Ingersoll-Rand

Ingersoll-Rand 2080-6 Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 231TL-2 Series Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 285B Series Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 231G Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 225 Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 2902 Series Guía de configuración

Ingersoll-Rand

Ingersoll-Rand 2015 MAX Series Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 251 Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 2131 Series Guía de configuración

Ingersoll-Rand

Ingersoll-Rand 2955B2 Guía de configuración

Ingersoll-Rand

Ingersoll-Rand 2955B2 Manual de usuario

Ingersoll-Rand

Ingersoll-Rand LA425-EU Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 2350XP Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 2850MAX Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 244 Manual de usuario

Ingersoll-Rand

Ingersoll-Rand Tp2301 Instrucciones originales

Ingersoll-Rand

Ingersoll-Rand 2130 Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 2920B-EU Series Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 2934P2 Guía de configuración

Ingersoll-Rand

Ingersoll-Rand 259 Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 2925B2Ti Guía de configuración

Ingersoll-Rand

Ingersoll-Rand 216B Manual de usuario

Ingersoll-Rand

Ingersoll-Rand 252 Manual de usuario

Manuales populares de Atornillador de impacto de otras marcas

stayer

stayer IW500D Manual de usuario

Makita

Makita DTD152 Manual de usuario

Milwaukee

Milwaukee M12 FID Manual de usuario

Grizzly

Grizzly H6140 Manual de usuario

Makita

Makita BTW450 Manual de usuario

Ozito

Ozito LID-3000 Manual de usuario

Astro Pneumatic Tool

Astro Pneumatic Tool 1812 Manual de usuario

Greenlee

Greenlee HW3 Manual de usuario

Sthor

Sthor 57091 Manual de usuario

Makita

Makita DTD145 Manual de usuario

Hilti

Hilti SIW 2-A12 Manual de usuario

Ryobi

Ryobi R18IW3 Manual de usuario

Parkside

Parkside PDSSA 20-Li A1 Manual de usuario

Flex

Flex FX1471 Manual de usuario

SATA

SATA 51075C Manual técnico

Cembre

Cembre NR-11P Manual de usuario

Makita

Makita BTP131RFE Manual de usuario

DeWalt

DeWalt XR Li-ion DCF902 Manual de usuario