Ingenic Newton Manual de usuario

Newton Development Platform

Hardware Manual

Date: 2014.08

Newton Development Platform

Hardware Manual

Release history

Date

Revision

Change

2014.02

1.0

First release

2014.05

1.1

1. Change the LCD description.

2. Add the part number of J5,J8,J9.

2014.08

1.2

1. Add the description of ceramic speaker.

2. Add the description of EVG.

3. Add the description of motor.

4. Add the description of NFC antenna.

Disclaimer

This documentation is provided for use with Ingenic products. No license to Ingenic property rights is

granted. Ingenic assumes no liability, provides no warranty either expressed or implied relating to the

usage, or intellectual property right infringement except as provided for by Ingenic Terms and

Conditions of Sale.

Ingenic products are not designed for and should not be used in any medical or life sustaining or

supporting equipment.

All information in this document should be treated as preliminary. Ingenic may make changes to this

document without notice. Anyone relying on this documentation should contact Ingenic for the current

documentation and errata.

Ingenic Semiconductor Co., Ltd.

Ingenic Headquarters, East Bldg. 14, Courtyard #10, Xibeiwang East Road, Haidian Dist.,

Beijing, China, 100193

Tel: 86-10-56345000

Fax: 86-10-56345001

Http: //www.ingenic.cn

Content

Newton Development Platform Hardware Manual

CONTENT

1OVERVIEW................................................................................................................................................. 1

1.1 HARDWARE FEATURES............................................................................................................................ 1

1.2 SYSTEM ARCHITECTURE......................................................................................................................... 2

2HARDWARE DESCRIPTION................................................................................................................... 3

2.1 PICTURE OF THE NEWTON BOARD .......................................................................................................... 3

2.2 POWER.................................................................................................................................................... 4

2.3 SYSTEM RESET....................................................................................................................................... 4

2.4 SYSTEM BOOT MODE............................................................................................................................... 4

2.5 FLASH AND MEMORY (LPDDR)............................................................................................................. 5

2.6 LCDAND TOUCH SCREEN INTERFACE.................................................................................................... 5

2.6.1 LCD Interface Definition............................................................................................................... 5

2.6.2 Touch Screen Interface................................................................................................................... 5

2.7 USB INTERFACE ..................................................................................................................................... 6

2.8 AUDIO SYSTEM....................................................................................................................................... 6

2.8.1 MIC.................................................................................................................................................... 6

2.8.2 SPEAKER............................................................................................................................................. 6

2.9 WIFI&BT&NFC.................................................................................................................................... 6

2.10 BUTTON INTERFACE ............................................................................................................................... 6

2.11 ECG SENSOR.......................................................................................................................................... 6

2.12 9-AXIS GYROSCOPE/ACCELEROMETER/MAGNETOMETER SENSOR......................................................... 7

2.13 EXTENDED DMIC &TEMPERATURE &HUMIDITY SENSOR .................................................................... 7

2.14 MOTOR................................................................................................................................................. 7

2.15 DEBUG INTERFACE ................................................................................................................................. 7

3QUICK START OF THE NEWTON BOARD.......................................................................................... 8

Overview

Newton Development Platform Hardware Manual

1 Overview

This document describes the hardware interface of the Ingenic Newton development board. Ingenic

Newton board integrates the Ingenic 1GHz JZ4775 processor, flash and memory, PMIC, Wi-Fi,

Bluetooth, NFC, 9-axis gyroscope/accelerometer/magnetometer sensor and ECG sensor on a small

module. It also provides several connectors for LCD, touch screen, temperature sensor, humidity

sensor, pressure sensor, DMIC and speaker. The Ingenic®Newton can run the latest version of

Android and Linux operating system, which makes it easy to develop various device drivers and

user applications on it.

1.1 Hardware Features

CPU: Ingenic JZ4775, up to 1.0 GHz.

Multimedia: H.264 720P@30fps Decoding.

Memory & Flash : KMS5U000JM-B308 (4GB eMMC + 3Gb LPDDR1)

LCD/TOUCH : 240X240 1.6" panel with capacitive touch screen, with backlight

2 buttons: POWER and RETURN buttons

USB 2.0: Micro USB device.

SDIO interface: Connect to WIFI.

PCM CODEC interface: Connect to the Bluetooth PCM interface.

UART: Two wires RS232 protocol, connect to the ECG sensor and Bluetooth.

SMB interface : Control PMU,capacitive touch screen, nine axes sensor, pressure

sensor(option), temperature & humidity sensor(option), NFC, Fuel Gauge

I2S interface : Connect to Digital MIC

Advanced power manager: Lithium battery charge; support RTC alarm and power up; very low

power consumption; battery charging status indicator and battery voltage monitor.

Overview

Newton Development Platform Hardware Manual

1.2 System Architecture

IOMEMORY

Debug

DEBUG

DA9024

PMU

GYROSCOPE

COMPASS

G-SENSOR WIFI

MSC1

WM-BAN-BM-13

NFC

PRESSURE

ECG-SENSOR

TH&HUMIDITY

I2S

GPIO

EMCP

LCD

MAX9788

Speaker

24M/26M

RTC

KEY

MEMBUS

CHARGER

I2C2 PCM

UART0

RGB I2C0

I2C1 UART2

USB DMIC

Jz4775

Driver

UART3

BAT 3.7-4.2V

USB-IN +5V

LCDPOWER

RTC

OTG

AOLON/P

Figure 1-1 Newton Development Platform System Architecture

Hardware Description

Newton Development Platform Hardware Manual

2 Hardware Description

This section describes every hardware module of the Ingenic Newton development board. For

details of the JZ4775, please refer to the datasheet and programmer guide of the JZ4775. For

details of each component, please refer to relative component datasheet. For details of the board,

please refer to board schematic.

2.1 Picture of the Newton Board

Figure 2-1 shows the picture of the main components and connectors of the Newton board. The

board size is 22 x 38mm.

Hardware Description

Newton Development Platform Hardware Manual

Figure 2-1 Ingenic Newton Board

2.2 Power

Newton board can be powered by USB and by a Li-on battery. The battery can only get 500mA from

the USB. Connect the Li-on battery with the board and press the POWER button, the ONKEY signal

of PMU will be pulled low. When PMU get this signal, it will power the system and send out a RESET

signal, the system starts working. You can press the POWER button keeping a few seconds to shut

down the system (controlled by software). When CPU receives the POWER signal, it will control

PMU to turn off the power of system by the SMB bus. If there is something out of control, you can

press the POWER button for 7.5 second; PMU will turn off the power and then reset the system.

The PMU chip is Dialog DA9024, powered +3.3V, +1.8V, +1.2V, +2.5V for system, VCORE of

DA9024 output +2.5V for RTC controller through a diode.

2.3 System Reset

When power on, PMU provides a RESET signal to CPU. When the system is power on, you can

press the POWER button for 7.5 second, and then the PMU will output a RESET signal to CPU.

2.4 System boot mode

The Newton board has 2 boot modes:

USB

Hardware Description

Newton Development Platform Hardware Manual

MSC0

Table 2-1 describes the setting of boot select:

Table 2-1 Boot Select

Boot Select

Boot From

Holding POWER and RETURN down together about 7s

USB Boot

Holding POWER down about 3s

MSC0 Boot ( default )

2.5 Flash and Memory (LPDDR)

The Newton board uses an eMCP with 32Gb eMMC and 3Gb LPDDR

2.6 LCD and Touch Screen Interface

2.6.1 LCD Interface Definition

The Newton board integrates an LCD connector J5 (BM10NB(0.8)-30DS-0.4V(51)), default is a

smart LCD interface.

Table 2-2 LCD Interface (J5) Signals Definition

Pin Number

Signal

Pin Number

Signal

VCI33

VDDIO18

BUS_SEL

LCD_RESET

NCS/CS

DNC/RS

GND

WR_E

RD_E

GND

DB7

DB6

DB5

DB4

DB3

DB2

DB1

DB0

SDA

LCD_BUSY

VLED+

VLED-

GND

The back light control chip is SGM3733BYTDI6G/TR in the main board, controlled by PWM of CPU,

the max current is 20mA.

2.6.2 Touch Screen Interface

J8 (BM10NB (0.8)-10DS-0.4V (51)) is the touch screen connector. The signal of J8 is defined in the

Table 2-3. Table 2-3 Touch Screen Connector (J8) Definition

Pin Number

Signal

Pin Number

Signal

VDDA33

IRQ

Hardware Description

Newton Development Platform Hardware Manual

SCL

GND

SDA

RESET

GND

VDD18

2.7 USB interface

The Newton board supports USB 2.0 device, it has 4 test points. When you insert the USB, the

board will be powered on.

2.8 Audio System

2.8.1 MIC

The Newton board supports a digital MIC in the external board.

2.8.2 Speaker

The Newton board can drive a piezoelectric ceramic speaker.

2.9 WIFI&BT&NFC

The Newton board integrates a WM-BAN-BM-13 module, which can communicate to other device

with WIFI or BT or NFC.

When using WIFI, the battery power is required. When using NFC, the antenna needs to make

changes based on the different usage of the antenna matching circuit.

2.10 Button Interface

There are two buttons, one is the POWER button and another is the RETURN button.

2.11 ECG Sensor

There is an ECG sensor on the Newton board. It can communicate to CPU by UART2. The ECG

sensor is optional and not provided default on delivery.

The cable and electrode requirements of the ECG sensor are as follows:

1) Material: The electrodes should be a metal with good conductivity, stainless steel 316L is

recommended.

2) Area: The area that the electrode contacted with the skin should be as large as possible,

100mm2at least. The larger area electrode has, the better the signal quality is.

3) Connection: The POGO pin, spring or shielding line can be used to contact the electrode with

the PCBA. Make sure that the input impedance of the ECG is less than 20m. The outside of the

shielding wire should be connected with analog ground.

4) When using, press the electrode with moderate strength, and hold the position fixed. If the

strength is changed, the input impedance will change, and then the ECG effect will be affected.

5) When using ECG, it is better to use battery as power supply.

Tabla de contenidos

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario