InfraScan 753 Manual de usuario

360°Infrascan®

Passive Infrared Motion Sensor

Installation Instructions

Please leave these instructions at

the installation site.

753

Series

753 Series 360° Infrascan Installation Instructions

Contents

1.0 Product Range..................................................................................................................3

2.0 Description........................................................................................................................3

3.0 Product Selection.............................................................................................................3

4.0 How it works .....................................................................................................................4

5.0 Identiﬁcation of Parts ......................................................................................................5

6.0 Installation of Location....................................................................................................6

7.0 Field of View......................................................................................................................6

8.0 Mounting Procedure.........................................................................................................7

9.0 Wiring Diagrams - 753 2-Wire Infrascan ........................................................................9

10.0 Wiring Diagrams - 753R 3-Wire Infrascan....................................................................10

11.0 Commissioning...............................................................................................................11

11.1 Set Up for Walk Test ................................................................................................11

11.2 Soft Start Feature ....................................................................................................11

12.0 Troubleshooting........................................................................................................... 12

13.0 Technical Speciﬁcations................................................................................................13

14.0 Warning- Using the 753 with Special Loads ................................................................15

15.0 Warranty ..........................................................................................................................16

753 Series 360° Infrascan Installation Instructions

3 of 16

1.0 Product Range

753 Infrascan 360 Degree, 240V a.c., 50Hz, 2-Wire, 2A,

20 Minute

753R Infrascan 360 Degree, 240V a.c., 50Hz, 3-Wire, 10A,

20 Minute

2.0 Description

The Clipsal 753 Series 360 Degree Infrascan is a highly reliable, state-of-the-art

passive infrared (PIR) occupancy sensor. The unit utilises an advanced quad-

element sensor array allowing instantaneous detection of movement and features

a massive 14 metre detection range.

The unit also features a slimline, fully recessed mounting facility, making it one of

the world’s most sleek and unobtrusive 360°sensors available.

The unit is designed to monitor the immediate environment, and detect people

moving within its ﬁeld of view. When movement is detected, the unit will activate an

electrical load, such as a light, in response to that movement.

Designed and developed in Australia, the unit offers beneﬁts in security, energy

management, hospitality and true ‘hands-free’ switching convenience in a wide

range of applications.

3.0 Product Selection

Be sure to select the appropriate Infrascan product to suit your application:

• the753isa2-wire(doesnotrequireNeutralconnection),andcanonlyswitcha

limited range of load types.

• the753Risa3-wiredevice(requiresNeutralconnectiontooperate)capableof

switching a wide range of load types.

* Please refer to Technical Speciﬁcations for further information about compatible load types.

Catalogue Number Neutral

Required Maximum Load*

753 NO 2A

753R YES 10A

753 Series 360° Infrascan Installation Instructions

4.0 How it Works

With power applied and a suitable load connected, the Infrascan can detect any

moving infrared source (for example a person) that may intrude upon its ﬁeld of view.

BoththeLight-LevelandTime-Onsettingsareuseradjustablebyremovalofthe

frontsurround.Simplytwisttoremovethecoverandadjusttrimpotasrequired.

TheLight-Leveladjustmentactivatestheloaddependentontheambientlight

levelintheeldofviewofthesensor.Thisadjustmentcanbesettoallowthe

Infrascan to operate the load at any light level between full daylight and almost

complete darkness. For example, the user can ensure the load is only activated

when movement is detected at night time. During the day time, when there is

adequate natural light, the unit can be set so it does not activate the load, as it is not

necessary to do so.

TheTime-Onadjustmentvariesthetimespanthattheloadwillremainonafter

the infrared source moves out of, or stops moving within the ﬁeld of view. The

loadwillautomaticallybeswitchedoffaftertheTime-Onperiodhaselapsed.Any

period between 5 seconds and approximately 20 minutes may be set by the time

adjustmentscrew.

Light-LevelAdjustment Time-OnAdjustment

Twist to Remove Surround

Note

• Thesensorheadisspeciallydesignedtogiveoptimumperformanceandis

sealed to prevent water or dust from entering the unit. Under no circumstances

should it be tampered with. There are no user serviceable parts inside.

• Donotapplyanypressureontheactualsensorlensitself,asthismaydamage

the lens, and adversely affect the performance of the unit.

753 Series 360° Infrascan Installation Instructions

5 of 16

5.0 Identification of Parts

Note

• Theunitissuppliedwithanoptionalzonemask,designedtoblocktheunitfrom

detecting motion in unwanted trip areas. This might include a smaller ofﬁce

space with an open doorway, where it is not desirable to activate lighting when

people pass by the open door.

• Thezonemaskincorporatesaseriesofstagedtear-awaysections,allowingfull

customisation of the ﬁeld of view. Tear away sections where you want detection

to take place.

• Totthezonemask,removethesurroundanduncliptheremovablespacer.

Clip the zone mask in place and replace the surround.

• Additionalzonemasksareavailable(ClipsalCatalogueNumber753MASK).

Surround

Spring Clips

Side Cable Entry

Apertures

Cable Clamp

Top Cable Entry

Terminal Cover Screw

Terminal Cover

Sensor Lens

UserAdjustments

Removable Spacer

753MASK-ZoneMask

Figure 2

753 Series 360° Infrascan Installation Instructions

6.0 Installation Location

An Infrascan must be positioned correctly to ensure effective operation. The ﬁeld

of view is optimum when the sensor head is mounted in a vertical position at a

height of 2.4 metres and the approach path is across the face of the sensor.

Note

• DonotmounttheInfrascanclosetoobjectswhichcancreaterapidtemperature

changes, e.g. air conditioning vents, heater ﬂues, moving water (i.e. fountains

and sprinklers). Avoid locations where condensation is likely to form on the lens.

• DonotmounttheInfrascanonanysurfacethatissubjecttomovementdueto

wind or other causes.

• Inallcases,locatetheInfrascansothattheapproachpathisacrosstheeldof

view and not directly towards the Infrascan, as a reduced detection range will

be observed.

7.0 Field of View

Arrows show direction of

approach for maximum

rated range.

Note:thattheeffective

ﬁeld of view is circular,

approximately 14m

diameter, when mounted

on a ceiling 2.4m above

the ﬂoor.

8m (26 ft)

6m (20 ft)

4m (13 ft)

2m (7 ft)

0m (0 ft)

2m (7 ft)

4m (13 ft)

Top view at 2.4m mounting height

0m (0 ft)

Side view

2.4m (8 ft)

2.7m (9 ft)

3.0m (10 ft)

3.7m (12 ft)12m

(39 ft) 12m

(39 ft)

10m

(33 ft) 10m

(33 ft)

(26 ft) 8m

(26 ft)

(20 ft) 6m

(20 ft)

(13 ft) 4m

(13 ft)

(7 ft) 2m

(7 ft)

(0 ft)

Floor

Ceiling

Note

• Thestatedeldofviewistypicalforfullbodymovementandissubjectto

variations caused by the type and quantity of clothing worn, as well as variable

background temperature characteristics and speed of movement.

• Rapidandlargetemperaturechangesmaybedetectedeveniftheyappeartobe

well beyond the ﬁeld of view due to reﬂection off surfaces that are within the ﬁeld

of view.

753 Series 360° Infrascan Installation Instructions

7 of 16

8.0 Mounting Procedures

Step 1

Using a hole saw or otherwise, cut a 50mm (2”) circular hole in the ceiling

(or ceiling tile). Draw cable through hole.

Step 2:

Remove terminal cover screw and terminal cover to expose terminals. Remove

cable entry tear-away(s) from the terminal cover as required, to suit incoming

cable.

Top Cable Entry

Punch out the top cable entry hole, then ﬁt the cable clamp to the terminal cover.

Push the two halves so that it snaps together, and clip onto the terminal cover

entry hole. The cable clamp wraps around the incoming cable. Feed cable through.

Side Entry

DONOTUSESIDEENTRY.

Step 3

Strip cable. Terminate

incoming wiring on the

appropriate terminals as

marked. Refer to Section

9 Wiring Diagrams

for further information

about wiring for different

applications.

Step 4

Fit the terminal cover,

and secure using the

terminal cover screw.

Step 5

Depress the outer

ends of the spring clips

towards the centre of the

unit and push the unit

through the hole until it

rests ﬂat on the ceiling.

30 12

753 LOOP LOOP LOAD A/L

753R LOOP N LOAD A/L

Terminal Detail

Cut and Strip Detail

Figure 4

753 Series 360° Infrascan Installation Instructions

Note

• Whenmountinginsuspendedceilingsthereshouldbeatleast140mmbetween

the lower surface of the tile and the hard surface above.

• Donotapplyanypressureontheactualsensorlensitselfasthismaydamage

the lens.

NextLevel/Roof

Terminal Cover

Spring Clips

Minimum Ceiling

Thickness 8mm

Surround

Lens

Cut a 50mm Circular Hole

in Ceiling (or Ceiling Tile)

140mm Minimum

126.5mm

90mm

Figure 5

A 72mm (2.83")

B 15mm (0.59")

C 89mm (3.50")

D 47mm (1.85")

E 50mm (1.97")

F 126.5mm (4.98")

Figure 6

753 Series 360° Infrascan Installation Instructions

9 of 16

9.0 Wiring Diagrams - 753 2-Wire Infrascan

1(a) Automatic operation

1(b) Automatic with manual override ON or OFF

1(c) ON, OFF or AUTOMATIC operation using a three position switch

Note

• WhenswitchingtoAUTOforanyoftheabovecongurationstheInfrascanwill

turnon.Allow30secondsplusTime-Onperiodforthesensortostabilisefor

normal operation. Wiring diagram 1(a), without override switches is preferred as

there is no settling period.

• Morethanone753CANNOTbeconnectedinparalleltoacommonload.

If parallel connection of multiple devices to control a common load is required,

useCat.No.753R.

Load

Active/Line

10A Fuse or MCB

753

Black/White

Red/Brown

Load

Active/Line

10A Fuse or MCB

753

Black/White2x30Mor30MAM

Off

Auto

On Auto

Load

Red/Brown

Load

Active/Line

753

Black/White39MAOM

Auto 10A Fuse or MCB

Off

Load

Red/Brown

Load

753 Series 360° Infrascan Installation Instructions

10A Fuse or MCB

753R

Load

Active

Black/Blue

Load

Red/Brown

White

Neutral

Auto

753R

39MAOM

10A Fuse or MCB

Off

Load

Active

Black/Blue

Load

Red/Brown

White

Neutral

10A Fuse or MCB

753R

2x30M or 30MAM

Auto

Load

Off

Active

Black/Blue

Load

Red/Brown

White

Neutral

Auto

10.0 Wiring Diagrams - 753R 3-Wire Infrascan

2(a) Automatic operation

2(b) Automatic with manual override ON or OFF

2(c) ON, OFF or AUTOMATIC operation using a three position switch

Warning

• Itisillegalforpersonsotherthanlicensedelectriciansorpersonsauthorised

by legislation to work on ﬁxed wiring of any electrical installation. Penalties for

conviction are severe.

• Installationmustbecarriedoutinaccordancewithlocalwiringrules(AS/

NZS3000AustraliaandNewZealand).

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario