InFocus IN42 Guía

Otros manuales para IN42

4

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Accesorios para proyectores de InFocus

InFocus

InFocus SP-CEIL-006 Manual de usuario

InFocus

InFocus LP 650 Guía

InFocus

InFocus SP-CEIL-012 Manual de usuario

InFocus

InFocus SP-LAMP-080 Guía

InFocus

InFocus WT96 Manual de usuario

InFocus

InFocus SP777 Manual de usuario

InFocus

InFocus SP-LAMP-088 Guía

InFocus

InFocus SP-LAMP-092 Guía

InFocus

InFocus SP-LAMP-086 Guía

InFocus

InFocus LiteShow 4 DB+ Manual de usuario

InFocus

InFocus SP-CEIL-001 Manual de usuario

InFocus

InFocus LiteProLS Manual de usuario

InFocus

InFocus RPM A-C Manual de usuario

InFocus

InFocus LP130 Guía

InFocus

InFocus SP-CEIL-010 Manual de usuario

InFocus

InFocus SP-LAMP-090 Guía

InFocus

InFocus SP-LAMP-073 Guía

InFocus

InFocus SP-CEIL-004 Manual de usuario

InFocus

InFocus IN2112 Guía

InFocus

InFocus LiteShow network adapter Manual de usuario

InFocus

InFocus SP-CEIL-008 Manual de usuario

InFocus

InFocus LP70+ Guía

InFocus

InFocus SP-CEIL-UNIV Guía

InFocus

InFocus CableWizard SP-CW3 Guía de inicio rápido

Manuales populares de Accesorios para proyectores de otras marcas

Optoma

Optoma BX-AL133B Manual de usuario

PEERLESS

PEERLESS PE 1120 Guía

Osram

Osram SIRIUS HRI Series Manual

Presentation Switchers

Presentation Switchers PS111 Manual de usuario

Kramer

Kramer VIA GO Manual de usuario

Yamaha

Yamaha PJL-112 Manual de lista de piezas

Swedstyle

Swedstyle CL23AA02ZA25E Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 236CB Manual del propietario

Epson

Epson BrightLink 475Wi Manual de usuario

Acer

Acer WP100 Manual de usuario

i3

i3 i3board Manual de usuario

CHIEF

CHIEF HB-43E Manual de usuario

Biamp

Biamp Modena Hub Manual de servicio

NEC

NEC MP10RX Manual de usuario

Panamorph

Panamorph DCR-S3 Manual de usuario

Exact solutions

Exact solutions FRAME-EVO-P10 Manual de usuario

CHIEF

CHIEF VCM103S Manual de usuario

Sharp

Sharp AN-PH20EZ Manual de usuario

34

Replacing the projection lamp

The lamp hour timer in the Service Info menu counts the number of hours

the lamp has been in use. Twenty hours before the specified end of the

lamp’s life, the message “Change lamp” briefly appears on the projected

screen.

NOTE: You can order new lamp housings from www.infocus.com (in select

areas), your retailer or your dealer. Use only a replacement lamp with the

same type and rating as the original lamp.

The part number is SP-LAMP-027.

1Turn off the projector and unplug the power cable.

2Wait 45 minutes to allow the projector to cool thoroughly.

3Loosen the lamp cover screw on the right side of the projector (marked

by the arrow) then slide and lift the lamp cover off.

WARNINGS:

• To avoid burns, allow the projector to cool for at least 45 minutes before

you replace the lamp.

• Do not drop the lamp module. The glass may shatter and cause injury.

Do not touch the glass lamp screen. Fingerprints can obscure projection

sharpness.

• Be extremely careful when removing the lamp housing. In the unlikely

event that the bulb ruptures, small glass fragments may be generated.

The lamp housing is designed to contain these fragments, but use cau-

tion when removing the lamp housing. Before replacing the lamp, clean

the lamp compartment and dispose of cleaning materials. Wash hands

after lamp replacement. This product has a lamp which contains a very

small amount of mercury. Dispose of it as required by local, state or fed-

eral ordinances and regulations. For more information see

www.eiae.org.

Service Info menu

turn off and unplug

the projector

wait 45 minutes

lamp cover screw

EDX Ref Guide.fm Page 34 Friday, June 30, 2006 10:48 AM

35

4Loosen the three captive screws (marked by the arrows) on the lamp

module.

5Carefully remove the lamp module by grasping and lifting the handle.

Dispose of the lamp in an environmentally proper manner.

6Install the new lamp module, making sure that it is properly seated, and

tighten the three captive screws.

7Replace the cover over the lamp module by sliding it back into place and

tightening the screw.

8Plug in the power cable, press the power switch then press the Power

button to turn the projector back on. Reset the lamp hour timer by navi-

gating to the Settings>Service menu and selecting Reset Lamp Hours.

loosen the captive screws on lamp module

lamp module handle

reset lamp hours in Service menu

EDX Ref Guide.fm Page 35 Friday, June 30, 2006 10:48 AM