inDESIGN MMP-1 Manual de usuario
MMP-1: INSTALLATION & OPERATION MANUAL
PAGE 2
The MMP-1 is a universal remote wall panel featuring three input
modes: BT, Line input and USB audio le playback. It can used
as a remote input to distributed audio systems, or on its own
connected directly to mixers, ampliers or speaker systems. Users
have the choice to connect the MMP-1 locally in an installed
space or connect to devices remotely via inexpensive CAT6A
twisted pair cabling.
The MMP-1 is the right choice for users who wish to install
multiple streaming receivers within close vicinity to one another.
With a few simple steps users are able to rename the BT ID to
differentiate installed MMP-1’s throughout buildings such as
schools, universities, ofce spaces and other training facilities.
INTRODUCTION
INTRODUCTION 2
IMPORTANT SAFETY
INSTRUCTIONS 3
IN THE BOX 4
INSTALL INSTRUCTIONS 4
FRONT PANEL 4
REAR PANEL 6
BT OPERATION 6
CONNECTIONS 8
SPECIFICATIONS 10
WARRANTY INFO 11
CONTENTS
Electrical and Safety Warnings
THESE SERVICE INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY.
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING
OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS
UNLESS YOU ARE QUALIFIED TO DO SO.
CAUTION
The lightening ash with arrowhead
symbol, with an equilateral triangle,
is intended to alert the user to the
presence of un-insulated
“dangerous voltage” within the products
enclosure that may be of sufcient
magnitude to constitute a risk of electric
shock to persons.
WARNING: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRICAL SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
MMP-1: INSTALLATION & OPERATION MANUAL PAGE 3
IMPORTANT SAFETY INSTRUCTIONS
WARNING: There are no user serviceable parts inside. Refer all servicing to qualied service personnel.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. To prevent injury please refer to these instructions for electrical and safety information before installing
or operating the apparatus.
6. No naked ame sources such as lighted candles should be placed on the apparatus.
7. Operation of this apparatus is recommended for moderate climates only.
8. This apparatus must not be exposed to dripping or splashing liquid.
No object lled with liquid, such as a vase, should be placed on the apparatus.
9. Clean only with a dry cloth.
10. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.
11. Do not install near any heat sources such as radiators, heaters, stoves, or other apparatuses
(including ampliers) that produce heat.
12. Unplug this apparatus during lightening storms or when not in use for long periods of time.
13. Protective Earthing Terminal:
The apparatus should be connected to a mains socket outlet with a protective earthing connection.
14. The mains plug/appliance coupler is used as a disconnect device, the disconnect device shall remain
readily operable.
15. When not in use and during transportation, please take care of the power cord set, for example, tie up
the power cord set with a cable tie/something similar. It should be kept away from sharp edges and
the like that can cause abrasion of the power cord set. When put into use again, check that the power
cord set is not damaged. If any damage is found, have the unit checked by a qualied service person
to replace the power cord set specied by the manufacturer.
16. The terminals marked with symbol of “ “ may be of sufcient magnitude to constitute a risk of
electric shock. The external wiring connected to the terminals requires installation by a qualied service
person or the use of ready-made leads or cords.
17. Only use attachments/accessories specied by the manufacturer.
18. Check speaker line load prior to connecting to amplier using an impedance meter.
19. Refer all servicing to qualied service personnel. Servicing is required if the apparatus has been
damaged in any way, such as power-supply cord or plug breakage, damage due to liquid or objects
falling onto the apparatus, exposure to rain or moisture, or if the apparatus does not operate normally,
or has been dropped.
20. Correct Disposal of this Product:
This marking indicates that this product should not be disposed of with other household wastes. To
prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle
it responsibly to promote the sustainable reuse of material resources. To return your used device, please
use the return and collection systems or contact the retailer where the product was purchased. They
can take this product for environmental-safe recycling.
MMP-1: INSTALLATION & OPERATION MANUAL
PAGE 4
WHAT’S IN THE BOX
1x JST3 to XLRF line input cable (300mm length)
1x JST3 to XLRM line output cable (300mm length)
1x RJ45 to XLRM cable (1 metre length)
1x PoE injector power supply with power cable
1x MMP-1 wall plate
1x The manual you are reading
INSTALLING YOUR MMP-1
Mounting your MMP-1 control panel is very easy. The MMP-1’s plastic fascia is based on Clipsal 2000 style
mountings. The MMP-1 is compatible with all Clipsal 2000 style mounting accessories, such as C-Clips and
standoff boxes.
Follow the appropriate instructions for the chosen installation accessory for the installation of your MMP-1.
The MMP-1 mounts in exactly the same way as a standard Australian/NZ mains outlet or light switch.
FRONT PANEL CONTROLS
1. VOLUME + : This button allows volume of playback audio to be increased.
2. VOLUME - : This button allows volume of playback audio to be decreased.
3. MODE: This button selects between different input source modes. As this button is pressed the MODE LED
will cycle Blue, Pink, or Red in colour.
MODE LED BLUE – BT Streaming Mode: In this mode the MMP-1 will accept BT streaming connections from
mobile and other BT streaming devices. Please see pairing section on page 6 for paring instructions.
*Note: Only one BT device can be connected at one time. To connect a different BT device to the MMP-
1 please see paring section.
1
2
3
4 5 6 7 8
9
10
MMP-1: INSTALLATION & OPERATION MANUAL PAGE 5
MODE LED PINK – LINE input mode: Devices connect via the 3.5mm stereo audio port, or devices
connected to the mono balanced rear port will pass audio through the MMP-1.
*Note: The 3.5mm stereo input on the front panel and the balanced input on the rear panel are shared
inputs. Audio signal will be audible from both inputs when in LINE mode if both of these audio inputs are
connected at the same time.
MODE LED RED – USB playback mode: In this mode the MMP-1 will play compatible les from the USB drive
plugged into the USB port on the from panel.
Compatible File types: MP3: Stereo les @ 128k, 192k, 320k and VBR bit rates.
*Note: USB drive must be formatted as FAT32.
4. PLAY/PAUSE button : This button has multiple functions, depending on which playback mode has
been selected.
BT Mode
PLAY/PAUSE button : Single short press, this button will play or pause the music le on the connected
BT device streaming to the MMP-1
PLAY/PAUSE button : Holding this button down for 8-10 seconds places the MMP-1 into BT paring
mode. Go to BT settings on your mobile device and pair it with the MMP-1.
USB Mode
PLAY/PAUSE button : Single short press, this button will play or pause music le on the USB drive
plugged into the MMP-1.
LINE Mode
PLAY/PAUSE button : This button has no function when the MMP-1 is in LINE mode.
5. Play mode button : This button allows the user to select playback mode of the USB drive when the
MMP-1 is in USB playback mode. As this button is pressed the Play Mode LED will cycle Blue, Red or Pink
in colour.
PLAY MODE LED BLUE = Plays all les on the USB drive in le name order.
PLAY MODE LED RED = Plays only one le on the USB drive.
PLAY MODE LED PINK = Plays les on the USB drive at random.
*Note: The Play mode button has no function when the MMP-1 is in BT or LINE mode.
6. Skip back button : When pressed once the skip back button will skip back to the start of a playing BT
stream or le. Pressing the skip back button twice will skip to the previous playback le. The skip back
button has the same function for BT connected devices and USB playback.
7. Skip Forward button : When pressed the skip forward button will skip to the next playable track on BT
connected devices and USB connected drives.
8. LINE: The 3.5mm Stereo line TRS audio input allows users to connect unbalanced audio device signals to
the MMP-1. To hear the audio please place the MMP-1 Into LINE mode via the MODE button. This stereo
input is internally summed to mono.
*Note: The 3.5mm stereo input on the front panel and the balanced input on the rear panel are shared
inputs. Audio signal will be audible from both inputs when in LINE mode if both of these audio inputs are
connected at the same time.
MMP-1: INSTALLATION & OPERATION MANUAL
PAGE 6
1. USB: The USB port allows users to plug USB thumb drives into the MMP-1. To playback music les from a
USB drive place, the MMP-1 into USB playback mode via the MODE button.
*Note: USB drive must be formatted as FAT32.
2. Sig LED: The signal LED will illuminate green when there is audible audio playback active on the MMP-1.
REAR PANEL CONNECTIONS
1. RJ45 connector: The RJ45 connector is used to power the MMP-1 and also serve as an audio bus
to remotely feed audio to other devices, such as mixers, mixer ampliers, ampliers, pre amps and
powered speakers.
*Note: Please see connection diagrams and cable recommendations on page 9 for more details.
2. LINE IN: This is a balanced mono line input. Please connect the JST3 to XLR Female cable adapter
(included) to connect balanced LINE output of a device. To hear audio connected to this port please
select LINE mode via the MODE button on the front panel of the MMP-1.
*Note: The 3.5mm stereo input on the front panel and the balanced input on the rear panel are shared
inputs. Audio signal will be audible from both inputs when in LINE mode if both of these audio inputs are
connected at the same time.
3. LINE OUTPUT: This is a balanced mono line output. Please use the JST3 to XLR Male adapter cable
(included) to balanced line input of a device.
*Please see connection diagram and cable recommendations on page 9 for more details.
BT OPERATION
The MMP-1 is capable of audio streaming from compatible BT devices. The BT transmission range between
the MMP-1 and streaming device should be within 20 metres of the MMP-1. Only one streaming device can
be connected to the MMP-1 at a time.
BT Paring
To pair your streaming device to the MMP-1 use the mode button to cycle through the different modes until
you see the blue LED light. In default the MMP-1 is unpaired and the blue LED will ash slowly.
Press and hold the play/pause button for 8-10 seconds until the blue LED ashes rapidly. Go to the BT
settings on your streaming device and pair with the MMP-1. The default BT id is “inDESIGN MMP-1”.
1
2 3
MMP-1: INSTALLATION & OPERATION MANUAL PAGE 7
Once paired with the MMP-1 the blue LED light will illuminate without ashing. Use any application on the
connected device from this point to stream audio to the MMP-1. There is no pairing password.
*Note: Ensure you have the volume on the streaming device turn up. The MMP-1’s volume control is
separate to the volume of the streaming device.
BT Unpairing
There are 2 different ways to unpair a BT connected device to the MMP-1.
1. When in BT mode hold down the play/pause button for approx. 8-10 seconds.
The blue LED will now ash slowly indicating the MMP-1 is unpaired from the streaming device.
2. Go to the BT menu of the device and choose forget or disconnect from MMP-1 and the streaming
device will disconnect from the MMP-1.
The blue LED on the MMP-1 will begin to ash slowly when disconnected.
BT Custom Naming
In situations where a user has multiple MMP-1 products in close vicinity of each other or the user wishes to
change the BT ID of an MMP-1, this can be easily achieved by following the below instructions.
1. Acquire a USB stick. Make sure there are no other les on the stick and it is formatted as a FAT32 partition.
2. In MS EXCEL create a new le.
3. In CELL A1 – Type text: BtName(Max 16)
4. In CELL A2 – Type your custom BT ID name (Max of 16 characters) example: AUDIO RULES!
5. Save the new le as: _BtName in CSV format.
6. Copy the le to the root directory of your USB drive.
7. With the MMP-1 powered on, insert the USB drive into the USB port.
On successful le read, the MMP-1 will ash together 2 x pink and 1 x Green LED 3 times.
8. Once this process has completed remove the USB drive.
The BT ID name change has now taken place and you may pair your BT streaming device with the MMP-1.
*Please see BT paring section on page 6 of this manual for pairing instructions.
*Note: Ensure the le is removed from the USB drive if you plan to use the same USB drive for audio playback
in the future.
MMP-1: INSTALLATION & OPERATION MANUAL
PAGE 8
The MMP-1 can be connected in different ways to various audio devices.
Please note the MMP-1 is designed to work using only one output connection at a time. Please see page 9.
*Note: Connecting multiple inputs and outputs and the same time could cause damage to the MMP-1, or
other connected equipment.
Cable Type
As power and audio travel along the same cable from the MMP1 - through the PoE power supply to other
devices, the category network cable connected between the MMP-1 and all devices must be of a high
quality.
A shielded category network cable with shielded RJ45 terminations must be used.
*Note: The minimum network category cable type requirement is CAT6A. The Length of cable must not
exceed 100 metres between the MMP-1 and PoE power supply. Cables must be terminated with shielded
RJ45 connectors in T-568B standard.
CONNECTING YOUR MMP-1
RJ45 PIN CONDUCTOR FUNCTION CAT 6A CONDUCTOR COLOUR
1Balanced audio + White + Orange
2Balanced audio - Orange
3 White + Green
4 Vsupply + 24V Blue
5Vsupply + 24V White + Blue
6Green
7Vsupply - 24V White + Brown
8 Vsupply - 24V Brown
Connector Screen Audio Ground Screen / Braid
MMP-1: INSTALLATION & OPERATION MANUAL PAGE 9
POE Power and Audio over shielded UTP Connection
This connection method allows users to power the MMP-1 via the included PoE power supply and route
balanced audio from the MMP-1 via the PoE power supply to a remote balanced line input.
POE Power and Audio via Tail connection
This connection method allows users to power the MMP-1 via the PoE power supply over network cable and
use the balanced LINE output on the rear panel to connect to a local (in room) balanced line input.
1. RJ45 to RJ45 shielded connectors. Use CAT6A network cable. Max length 100m
2. PoE Power Supply (included)
3. RJ45-LAN-XLR Male Patch Cable (included)
4. Balanced line input of a mixer, mixer amplier, amplier or powered speaker
*Note: in this conguration the balanced line output on the rear of the MMP-1 should not be used.
1. RJ45 to RJ45 shielded connectors. Use CAT6A network cable. Max length 100m
2. PoE Power Supply (included)
3. JST3-XLR Male cable (included)
4. Balanced line input of a mixer, mixer amplier, amplier or powered speaker
*Note: in this conguration the balanced line output of the PoE power supply should not be used.
1 3
2
1 3
2
4
4
MMP-1: INSTALLATION & OPERATION MANUAL
PAGE 10
SPECIFICATIONS
Product Mounting Compatible with Clipsal 2000 series mounting accessories
AC Power Supply to PoE AC 100-240V 50/60Hz
MMP-1 Power Supply DC PoE 24VDC 1.0A
BT Revision BT 4.2
BT Range 20 metres
USB Flash Drive Flash drive capacity MAX 128GB / FAT32 partition
USB Player MP3: Stereo les @ 128k, 192k, 320k and VBR bit rates
Front panel line input TRS 3.5mm unbalanced jack (0.3v level, impedance 10K, internal mono
sum)
Rear panel line input JST3 balanced (0.5v level, impedance 10K, mono input)
Rear Panel line output JST3 balanced (0.5v level, impedance 600ohms, mono output)
PoE line output RJ45 balanced (0.5v level, impedance 600ohms, mono output)
Product Dimensions HxWxD 76 x 118 x 32 mm (Clipsal 2000 series style mounting)
Product Weight 100 grams
Shipping Dimensions HxWxD 255x200x70 mm
Shipping Weight 660 grams
Included Accessories PoE power supply , Line in and out cable, RJ45 line cable
* Disclaimer: Instructions and specications are correct at time of printing.
Information within may be subject to change without notice.
inLINK Connection
The MMP-1 may be connected directly into any inDESIGN product that features an inLINK port. For specic
installation and user instructions please view the user manual for the specic device you wish to connect the
MMP-1 to.
1. RJ45 to RJ45 shielded connectors. Use CAT6A network cable. Max length 100m
2. inDESIGN InLINK Port
*Note: in this conguration the balanced line output on the rear of the MMP-1 should not be used.
1
2
Tabla de contenidos
