IN2UIT Collage Manual de usuario
IN2UITCOLLAGE
OWNER’S MANUAL
1
Dear Audiophile,
Thank you for purchasing ‘Collage’ by IN2UIT. Filo features hi-end tweeters using the proprietary SBESL
(Self-Biased ElectroStatic Loudspeaker) acoustic technology that we refer to as ELECTROSTATZ®. The
acoustic performance and reproduction are of the highest quality and level, revitalizing your many familiar
sounding recordings into a new listening experience.
We wish you many years of enjoyment through Collage,
our ultra-high performance Bluetooth mobile speaker.
2
PACKAGE CONTENTS
OVERVIEW
PLACING YOUR SPEAKER
OPERATING
CARE & MAINTENANCE
CONTACTING CUSTOMER SERVICE
TROUBLESHOOTING
WARRANTY
TECHNICAL SPECIFICATIONS
4
5
7
11
18
19
20
20
21
3
Collage - Bluetooth mobile speaker device X1
15V / 4A DC power adaptor X1
stand X1
PE bag X1 (include：2 x screws )
measurement paper X1
warranty card X1
1
2
3
4
5
6
PACKAGE CONTENTS
1 2 3
4
5
4
Measurement Paper
15V / 4A DC power adaptor
6
Power / Bluetooth pairing button X1
Power / Bluetooth LED indicator X1
SBESL ELECTROSTATZ®tweeters X2
(LHS / RHS stereo sound)
1
2
3
FRONTVIEW
3
5
POWER
2
1
LED
3.5mm stereo input jack X1
DC-in socket X1
SBESL ELECTROSTATZ®tweeter X2
Wall mounting receptacle
Flip-out stand
1
2
3
4
5
REAR PANEL
1
2
33
4
5
6
DC-IN
3.5mm
JACK
For desktop usage, embedding operation is simple (see
the picture inset), just align the stand protrusion with the
rectangle stand receptacle in the bottom of the unit. Make
sure it is seated and engaged properly.
There are two screw holes of the bottom of the stand. They
should automatically align the screw holes of the bottom
of the unit.
Secure the stand to the unit using the screws (x2)
provided.
For best bass response, the speaker should be placed
near a wall.
To avoid adverse sound quality, do not place the speaker in
confined areas that are enclosed or block the sound wave
dynamics.
1
2
3
4
5
PLACING ON YOUR DESTOP
7
MOUNTING YOUR SPEAKER ON A WALL
Place the measurement paper provided in the desired location against the
wall and mark the screw locations (x2) with a pencil, using the measurement
paper as a template. Use a tape measure to measure the height from the
floor to the marked holes and make sure they are level and equidistant. If
you plan to feed wires through the wall, mark the pilot hole position first.
Choose the screws to fit the hole of the wall-mounting bracket, however if
your wall surface is hard, like concrete, drill pilot holes to insert anchor
plugs for the screws to engage with. Remember always measure twice.
Secure the screws (x2) on the wall.
Mounting operation is simple (see the picture inset), just hanging the
wall-mounting bracket of the Collage speaker on the screws. The speaker
now is ready to use.
1
2
3
4
8
NOTICE!
Do not mount the speaker on surfaces that are not sturdy enough, or have
hazards, such as electrical wire or plumbing, concealed behind them. If
you are unsure about installing the speaker, contact a qualified professional.
The brackets were specifically designed to support the weight
of‘Collage’only.
NOTICE!
The ELECTROSTATZ™ tweeter panels, LHS & RHS, are dipole i.e. sound waves
travel in both directions. To maintain the highest quality acoustic
performance, never block the rear sound output area and always maintain at
least a 3cm distance between the tweeter panels and the wall. The mounting
bracket will automatically provided the clearance required.
9
CONNECTING THE AC POWER
NOTICE!
For safety purposes always turn off the main power switch when
plugging or unplugging in the device.
The universal power adaptor that comes with Collage accepts multiple
voltages (100-240V); however users are advised to check regional AC
voltage supply and plug type before connecting to the power supply.
Prior to connecting to the power supply, make sure the
speakers are switched off first. Engage the male DC-in plug and female
DC-in receptacle on the rear of the device. Turn on the speakers’ power
as indicated below.
10
Otros manuales para Collage
1
Tabla de contenidos
Otros manuales de Oradores de IN2UIT
