Imtradex Talk2Guide Manual de usuario
IMTRADEX HÖR-SPRECHSYSTEME e.U.
Industriestraße 60a/122 •A-1220 Wien / Austria •Telefon: +43 / 1 / 20 44 294-0 •Telefax: +43 / 1 /2044294-18
registr. beim Handelsgericht Wien FN 445229z •UID-Nr. ATU37332409 •www.headsets.at •www.imtradex.at
MANUAL Talk2Guide
Diagram and Instructions
1. Antenna (for Transmitter only)
2. LCD display
3. Down button for channel and volume adjustment
4. On / Off / Mute / Set button - Transmitter
additionalfunction for Transmitter: to mute the audio signal
On / Off/ Set button - Receiver
5. Up button for channel and volume adjustment
6. Microphone Headset / Aux input for Transmitter
Earphone output for Receiver
7. Built-in microphone hole on the Receiver
8. Lanyard connection point
9. Two-Way communication switch - Transmitter
10. Push talk button - Receiver
11. Label area
12. Battery compartment and built-in Li-polymer battery
13. Lid 01 battery compartment and
14. Micro-USB charging slot
IMTRADEX HÖR-SPRECHSYSTEME e.U.
Industriestraße 60a/122 •A-1220 Wien / Austria •Telefon: +43 / 1 / 20 44 294-0 •Telefax: +43 / 1 /2044294-18
registr. beim Handelsgericht Wien FN 445229z •UID-Nr. ATU37332409 •www.headsets.at •www.imtradex.at
LCD Display Illustration
Operating Instructions
Microphone and Earphone Connection
• Connect the microphone / headset to the 3.5mm socket on the transmitter and the earphones to the
3.5mm socket on the receiver. Make sure the connectors are properly inserted in place
Power On and Off
• Press and hold the power button / for 2 seconds to turn on the system. The LCD display will
illuminate and retrieve the channel number used last time to indicate Power on successfully
• Press and hold the power button / for 2 seconds. The LCD display will disappear to indicate Power off
completely.
Note:
• Energy saving- Receiver will automatically power offif no signal is received after about 20min
How to select a channel
•The channel is preset to ，lf you wish to select a different channel, press and buttons
simultaneouslyfor 2 seconds. The : CH: sign starts flashing and icon is removed to indicate channel
escape from lock mode. Press and button to select your desired channel. Press / button
briefly to confirm the selected channel or wait for approximately 5 seconds to automatically store and
lock the selected channel. will stop flashing and LCD displays icon. System now returns to
lock mode
Note:
• Make sure that the transmitter and receiver(s) operate on the same channel. The receiver display will
keepflashing when no transmission signal is being received
• System will retrieve the channel number used previously .
• Channel SYNC -Receiver(s) which operates on same channel of the transmitter will be synced
wirelessly when the channel in the transmitter has been changed as synchronization feature
IMTRADEX HÖR-SPRECHSYSTEME e.U.
Industriestraße 60a/122 •A-1220 Wien / Austria •Telefon: +43 / 1 / 20 44 294-0 •Telefax: +43 / 1 /2044294-18
registr. beim Handelsgericht Wien FN 445229z •UID-Nr. ATU37332409 •www.headsets.at •www.imtradex.at
How to adjust the Volume
Transmitter: Using the LapelMic Headset
The Aux input port on the headset accepts external
line-Ievel audio source, For example CD/MP3 player. An ideal
toolfor you to play audio source while making a speech
• Connect the headset to the 3.5mm socket on the transmitter
•Transmitter volume is preset at level
•Press and button to decrease or increase the volume level. There are 4 adjustable levels from to
• Press mute button briefly to mute the transmitter, press the same button one again to recover.
•The headset features a microphone-mute switch; Switch to”mute” when you like to
play the aux input source alone or to have private conversation
Transmitter:Using other microphones / headsets
The 3.5mm socket on the transmitter accepts mic and line level input source
The default input is set to microphone level
• Connect microphone to the 3.5mm socket on the transmitter
• Transmitter volume is preset at level 4
• Press or button to decrease or increase the volume level. There are 4 adjustable levels from to
•Press mute button briefly to mute the transmitter, press the same button one again to recover.
How to switch to line/mic level input manually
If you are connecting an aux input source to the transmitter, you must switch the default input level
from microphone level to line level manually
• To switch to line level, press and hold the button for 5 seconds until the flashing speaker sign and solid level 1
segment appear
• press or button to decrease or increasethe volume level. There are 8 adjustable levels from
to
• Press mute button briefly to mute the transmitter, press the same button once again to
recover
• To switch back to microphone level, press and hold the button for 5 seconds until the solid speaker sign and solid
level 4 segment appears
Receiver:
• Receiver volume is preset at level 4
• In normal state be displayed, press or button to decrease or increase the volume level. There
are 8 adjustable levels lrom ~ to" 1111111 . The LCD display ~ indicates no volume and in mute mode.
•The LCD display indicates no volume and in mute mode.
IMTRADEX HÖR-SPRECHSYSTEME e.U.
Industriestraße 60a/122 •A-1220 Wien / Austria •Telefon: +43 / 1 / 20 44 294-0 •Telefax: +43 / 1 /2044294-18
registr. beim Handelsgericht Wien FN 445229z •UID-Nr. ATU37332409 •www.headsets.at •www.imtradex.at
Initiate Two Way Communication Function
The transmitter has the control of activating the two-way function. While transmitter is speaking, system
allows one of the receivers to join the conversation. The conversation will be heard by all theparticipant
within the group
• Slid the two-way communication switch located on the side 01 the transmitter to “ On " position
, both the speaker sign and level segment will start flashing on the transmitter LCD display
The volume level segment now represents the earphone volume level of the transmitter. Press or
button to decrease or increase theearphonevolume. Please do not forget to attach the
earpiece 01 the headset to your ear.
• The receiver can make speech by pressing and holding the talk button on
theside and speak to the built-in mic on top. Release the talk button after the end of the speech and allow next
person to speak.
• Slid the switch “ Off“on the side of the transmitter to end this feature
Battery Autonomy and Charging
• When battery icon is displayed at fully autonomy , the battery contains sufficient power.
• When the battery icon is displayed as empty and flashing , this indicates low battery and only
10% battery remaining. Recharge the battery immediately via USB certified traveling charger
(optional accessories) or appropriated Linkx charger station. It will take approx. 6 hours to reach full
charge and provide approx. 15 hours of continuous operation for receiver and 12 hours of continuous
operationfor transmitter
• When charging, the battery icon displays on LCD back and forth.
Note: .
• The transmitter or receiver will shut down automatically when charging is taking place. If you want to
use the system while it's charging, simply press the power button again to turn the system back on.
Tabla de contenidos
