Impex APEX II Manual de usuario

NOTE:

Please read all instructions

carefully before using this

product

Safety Notice

Hardware Identifier

Assembly Instruction

Parts List

Resistance Chart

Warranty

Ordering Parts

Model

APEX II

Retain This

Manual for

Reference

08-14-01

OWNER'S

MANUAL

MARCY HOME GYM

APEX II

IMPEX FITNESS PRODUCTS

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: (800) 999-8899 Fax: (626) 961-9966

www.impex-fitness.com

[email protected]

TABLE OF CONTENTS

BEFORE YOU BEGIN....................................................................................……….. 1

IMPORTANT SAFETY NOTICES...................................................................……….. 2

HARDWARE IDENTIFIER.....….....................................................................……….. 3

ASSEMBLY INSTRUCTIONS.........................................................................……….. 4

HOW TO USE..................................................................................................………..18

PARTS LIST…………………………………………………………………………………..19

RESISTANCE CHART………….......................................................................………. 20

WARRANTY.................................................................................................…………. 21

ORDERING PARTS.......................................................................................…………21

BEFORE YOU BEGIN

Thank you for selecting the MARCY APEX II HOME GYM by IMPEX FITNESS

PRODUCTS. For your safety and benefit, read this manual carefully before using

the machine. As a manufacturer, we are committed to provide you complete

customer satisfaction. If you have any questions, or find there are missing or

damaged parts, we guarantee you complete satisfaction through direct

assistance from our factory. To avoid unnecessary delays, please call our TOO-

FREE customer service number. Our Customer Service Agents will provide

immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. – Fri. 9 a.m. – 5 p.m. PST

www.impex-fitness.com

[email protected]m

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply

whenever you operate a piece of exercise equipment. Be sure to read the entire manual

before you assemble or operate your machine. In particular, note the following safety

precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal

symptoms, STOP the workout at once. CONSULT A PHYSICIAN

IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine

near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear

robes or other clothing that could become caught in the machine. Running

or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO

NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or

physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to

properly warm up.

11. Never operate the machine if the machine is not functioning properly.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR

PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF

35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL

INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO

RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY

OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches, two Allen Wrenches,

and one Flat Head Screwdriver. NOTE: It is strongly recommended this machine to be

assembled by two or more people to avoid possible injury.

STEP 1 (See Diagram 1)

A.) Connect the Main Base Frame (#1) and Rear Vertical Beam (#4) to the Rear Stabilizer (#9).

Align the holes then secure them with two M10 x 2 ¾” Carriage Bolts (#79), ∅¾” Washers

(#94), and M10 Aircraft Nuts (#96). DO NOT tighten all the nuts and bolts yet.

B.) Attach the Front Stabilizer (#6) to the Main Base Frame (#1). Secure it with three M10 x 5/8”

Allen Bolts (#88) and ∅¾” Washers (#94). Insert the Foot Plate Axle (#99) into the Foot Plate

(#7). Attach the Foot Plate to the Front Stabilizer and secure it with two M10 x ¾” Allen Bolts

(#82) and ∅¾” Washers (#94).

C.)Attach the Front Vertical Beam (#2) to the Main Base Frame (#1). Secure it with two M10 x 2

¾” Carriage Bolts (#79), ∅¾” Washers (#94), and M10 Aircraft Nuts (#96).

D.)Place the Upper Frame (#3) onto the Front Vertical Beam (#2). Secure it with a 6¼” Bracket

(#29), two M10 x 2 ¾” Carriage Bolts (#79), ∅¾” Washers (#94), and M10 Aircraft Nuts (#96).

E.) Attach the rear of Upper Frame (#3) to the Rear Vertical Beam (#4).Secure it with a 4” Bracket

(#28), M10x2½” Allen Bolt (#85) and ∅3/4” Washer (#94) to the upper hole. Secure the lower

hole with a M10 x 2 ¾” Carriage Bolt (#79), ∅¾” Washer (#94), and M10 Aircraft Nut (#96).

DIAGRAM 1

STEP 2 (See Diagram 2)

A.) Place two Rubber Bumpers (#72) onto the Main Base Frame (#1). Align the holes and push

two Guide Rods (#8) through the Bumpers into the Main Base Frame (#1).

B.) Install fourteen Weight Plates (#42). To install the plate, hold the plate at an angle and place

it in between the two Guide Rods then drop it down. NOTE: Make sure the groves on the

plastic covers all face up. Insert the Selector Rod (#41) into the center hole on the plates.

Slide the Selector Stem (#40) onto the Guide Rods (#8) from the top. Align the holes and

secure the Selector Stem (#40) to the Selector Rod (#41) with a M10 x 1 ¾” Allen Bolt (Full

Thread) (#101).

C.)It is strongly recommended to spay lubricant such as WD-40 on the two Guide Rods to

minimize friction. Please note this machine comes with 14 plates. You can purchase

another 5 more plates (Model no. WK51) in the future to increase the weights.

D.)Attach the Top Socket Assembly (#5) to the top of the Guide Rods (#8). Secure the

Assembly to the Upper Frame (#3) with a 4 ¾” Bracket (#27), two M10 x 2 ¾” Carriage Bolts

(#79), two ∅¾” Washers (#94), and two M10 Aircraft Nuts (#96).

E.) Insert the Weight Selector Pin (#39) into the selected stack of Weight Plates to obtain the

desired weights for exercise. Make sure the magnet on the Pin faces up.

F.) Securely tighten all the nuts and bolts previously installed.

DIAGRAM 2

STEP 3 (See Diagram 3)

A.) Attach the Backrest Board (#23) to the Backrest Support (#16). Secure it with two M8 x 1

5/8” Allen Bolts (#89) and ∅5/8” Washers (#93).

B.) Push two ∅1” Bushings (#70) to the holes on the Front Vertical Beam (#2) from both sides.

Attach the Backrest Support (#16) to the holes. Secure it with one M12 x 3 ½” Allen Bolt

(#80), two ∅1” Washers (#95), and one M12 Aircraft Nut (#97). Secure the Backrest

Support with a Pull Pin (#48) on the Front Vertical Beam (#2).

C.) Attach the Seat Support (#10) to the Front Vertical Beam (#2). Secure it with One M10 x 2

¾” Carriage Bolt (#79), ∅¾” Washer (#94), and M10 Aircraft Nut (#96). Push a 2” Flat End

Cap (#66) into the front end of the Seat Support (#10). DIAGRAM 3

STEP 4 (See Diagram 4)

A.) Attach two ∅1 5/8” x ¼” Bushings (#76) to the holes on the Upper Frame (#3). Attach the

Front Press Base (#14) to the Bushings. Align the holes then insert a 7” Axle (#33) through

the holes. Secure the Axle with two M6 x ¼” Slotted Set Screws (#92).

B.) Insert a M10 x 6 ¾” Allen Bolt (#84) through the upper holes on the Front Press Base (#14).

Securely tighten it with two ∅¾” Washers (#94) and one M10 Aircraft Nut (#96).

C.)Attach two Front Support Frames (#11) to the Main Base Frame (#1). Secure it with one M10

x 2 ¾” Carriage Bolt (#79), ∅¾” Washer (#94), and M10 Aircraft Nut (#96).

D.)Attach the Frames to the Seat Support (#10). Secure them with one M10 x 2 ¾” Carriage

Bolt (#79), ∅¾” Washer (#94), and M10 Aircraft Nut (#96).

E.) Attach two ∅1” Bushings (#70) to the Leg Developer (#12). Place the Leg Developer in

between the two Support Frames. Align the holes and secure it with one M12 x 3” Allen Bolt

(#81), two ∅1” Washers (#95), and one M12 Aircraft Nut (#97). DIAGRAM 4



STEP 5 (See Diagram 5)

A.) Attach two ∅1 5/8” x ½” Bushings (#75) to the Front Press Base (#14). Attach the Front

Press (#15) to the Base. Align the holes then insert a M12 x 10 ¾” Axle (#34) through

the holes. Secure the Axle with two ∅1 ¼” Washers (#74) and two M12 Aircraft Nuts

(#97). Note: Do not over tighten the nuts. Make sure the Front Press Is able to Swivel.

B.) Secure the two M6 x ¼” Slotted Set Screws (#92) on the Front Press with a Flat Head

Screwdriver. Attach a Pull Pin (#48) to the left side of Front Press (#15).

C.)Attach the Butterfly Pulley Bracket (#19) onto the Main Base Frame (#1). Secure it with

two M10 x 2 ¾” Carriage Bolts (#79), ∅¾” Washers (#94), and M10 Aircraft Nuts (#96).

DIAGRAM 5

STEP 6 (See Diagram 6)

A.) Attach the Butterfly Base (#18) to the Front Vertical Beam (#2). Secure it with one 4 ¾”

Bracket (#27), two M10 x 3 ½” Carriage Bolts (#78), ∅¾” Washers (#94), and M10

Aircraft Nuts (#96).

B.) Insert the Right Butterfly (#21) through the right hole on the Butterfly Base. Secure it with

one M12 x 5/8” Allen Bolt (#83) and ∅1 ½” Washer (#73). Plug a ∅1 ½” Round End Cap

(#63) to the end opening on the Butterfly. Repeat the same step to install the other side.

C.)Insert one Butterfly Handle (#17) through the pivot hole on the Right Butterfly (#21).

Secure it with one M12 x 5/8” Allen Bolt (#83) and ∅1 ½” Washer (#73). Secure a M10 x

1” Allen Bolt (Half Thread) (#90) through the slotted hole on the pivot into the Handle.

Repeat the same step to install the other side.

DIAGRAM6

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Gimnasio en casa de Impex

Impex

Impex MARCY MWB-70500 Manual de usuario

Impex

Impex MARCY SM-6001 Manual de usuario

Impex

Impex MARCY PLATINUM MP 2100 Manual de usuario

Impex

Impex POWERHOUSE PHC 764 Manual de usuario

Impex

Impex Competitor WM-205 Manual de usuario

Impex

Impex JD-1.2 Manual de usuario

Impex

Impex PLATINUM MARCY PM-3000 Manual de usuario

Impex

Impex APEX AX-2109.1 Manual de usuario

Impex

Impex Powerhouse Club PHC 750 Manual de usuario

Impex

Impex COMPETITOR WM-1505 Manual de usuario

Impex

Impex MARCY PRO SM-7362 Manual de usuario

Impex

Impex MARCY MP-3205 Manual de usuario

Impex

Impex IRON GRIP STRENGTH TSA-41 Manual de usuario

Impex

Impex Iron Grip Strength IGS-46 Manual de usuario

Impex

Impex MARCY PRO TC-4699 Manual de usuario

Impex

Impex SB 650W Manual de usuario

Impex

Impex Apex TC-3500 Manual de usuario

Impex

Impex MARCY MWB-479 Manual de usuario

Impex

Impex MARCY MWM-1100 Manual de usuario

Impex

Impex SB 661 Manual de usuario

Impex

Impex Apex TC-3500 Manual de usuario

Impex

Impex TSA-42 Manual de usuario

Impex

Impex MWM 982 Manual de usuario

Impex

Impex APEX WM-348.1 Manual de usuario

Manuales populares de Gimnasio en casa de otras marcas

Horizon Fitness

Horizon Fitness OXFORD 6 Manual de usuario

Energetics

Energetics Multi Trainer 5.1 Manual de usuario

Matrix

Matrix MG-PL Series Manual de usuario

Reebok

Reebok Tbr2i Manual de operación y mantenimiento

Weider

Weider 8300 Hard Drive Manual de usuario

Pure Fitness

Pure Fitness 8526HE Manual de usuario

Weider

Weider 8700 I Guía de inicio rápido

Bowflex

Bowflex Sport 001-6961 Manual de usuario

NordicTrack

NordicTrack E8200 Competition Bench Guía de inicio rápido

Weider

Weider WEMC10161 Manual de usuario

Body Solid

Body Solid GHYP-345 Manual de usuario

Evo

Evo TAHOE 5105 Manual de usuario

cardiobull

cardiobull RA17 Manual de usuario

ParaBody

ParaBody 40 Manual de usuario

JLL

JLL Ventus Pro Air Power Manual de usuario

Trojan

Trojan Colorado 370 Manual de usuario

Octane Fitness

Octane Fitness xRide xR650 Manual de usuario

Precor

Precor Discovery Series Manual de usuario