2. Locate the SIM/Micro SD Card Slot on the side of the device.
3. Insert a pin into the SIM/Micro SD Card Slot pinhole.
4. Gently push the pin until the SIM tray pops out.
5. Pull the SIM tray out.
6. Insert the SIM or Micro SD card into the proper slot.
7. Slide the SIM tray back into place.
Scanning a Barcode Label
1. Point the scan window at the barcode you wish to scan.
2. Tap Scan on the Scan app screen or press a scan button on the TC601.
3. The imager projects a laser aiming pattern to position the barcode in the imager’s field of
view. Center the laser red dot and cross-hair aiming pattern on the bar code.
4. Release the scan button to capture and decode the image.
Laser Safety
Do not stare into the beam of the laser light from this device. The TC601 uses an imager
Aiming System with a laser light that is visible to the human eye and is emitted from the scan
window at the top of the device.
Laser Light - Do not stare into this Beam Class 2 Laser Product.
The maximum output radiation is 1 mW compliant with EN
60825-1 (2007)
Important Notices and Precautions
The manufacturer has made safety the first priority during the design stage. To avoid
potential mishaps, please observe the following notices and precautions:
Do not stock this device under high temperature conditions that may
cause the battery to overheat.
Do not charge longer than required. When the charging light is red, stop
charging immediately.
Charge this device in place without any water-spray or moisture.
Use a dry cloth to wipe any dust off of the AC adapter plug to avoid
potential fire.
Do not drop this device on hard surfaces.
Do not place heavy objects on this device to avoid cracking the
enclosure.
Do not unplug the AC adapter with wet hands to avoid electric shock.
Do not use the AC adapter of the TC601 with any other devices.
➢Do not place the device in liquids to prevent short-circuits or fire.
➢Do not place this device near an open fire.
➢If the power or USB cable is seriously twisted or broken, stop using
immediately to prevent electric shock, short-circuit, or fire.
➢Stop using immediately if there is any unusual smell or overheating
during charging or operation.
➢Stop using immediately when there is liquid or dew on the device.
Do not use the AC adapter outdoors
Please do not wrap the AC adapter with cloth or other objects that could
block heat dissipation and cause electric shock or fire.
When not charging, remove the AC adapter plug from the wall AC outlet
socket to avoid a fire hazard.
Important Notices When Using
Before replacing the battery pack due to failure, shortened life, or unusual behavior, please
confirm that the device has been used correctly, with no user operation issues involved.
The manufacturer is not responsible for possible missing data or interference encountered
during wireless transmissions.
Do not use alcohol, benzene, organic solvents, cleaning liquid, or steel wool on the surface
of this device.
Do not scratch or mar the surface of the Scan Window in any way to avoid barcode
scanning problems.
Bluetooth
This device is designed based on Bluetooth standard specifications. However,
compatibility problems may still occur with other Bluetooth devices.
Before using this device, please make sure there is no other wireless device operating
within a short distance of the same application area that may cause wireless signal
interference.
Signal Interference from TV or Radio
Sometimes transmitting or receiving data may fail due to signal interference from nearby
TV or radio devices.
Audio Safety
To prevent possible hearing damage, do not listen at high
volume levels for long periods of time.
European Union Regulatory Notes
1. Requirements for AT/BE/BG/CZ/DK/EE/FR/DE/IS/IE/IT/EL/ES/CY/LV /LI/LT/LU/HU
/MT/NL/NO/PL/PT/RO/SI/SK/TR/FI/SE/CH/UK/HR.5150MHz~5350MHz is for indoor use
only.
2. iWaylink INC declares that the radio equipment type for the TC601 is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
www.iwaypro.com
SAR Compliance
SAR Information (European Union):
Head: 0.401 W/kg@ 10g (CE)
Body: 0.906 W/kg@ 10g (CE)
This device is restricted to indoor use when operating in the 5150 to 5350 MHz frequency
range.
Body-worn Operation
This device was tested for typical body-worn operations. A minimum separation distance
must be maintained between the user’s body and the handset, including the antenna:
0.5 cm to comply with the RF exposure requirements in Europe Third-party belt-clips,
holsters and similar accessories used by this device should not contain any metallic
components. Body-warn accessories that do not meet these requirements may not comply
with RF exposure requirements and should be avoided.
Power and Frequency Ranges For Europe
For the TC601
FCC Warning Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
This device meets all the other requirements specified in Part 15E, Section 15.407 of the
FCC Rules.
The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device has
also been tested against this SAR limit. This device was tested for typical body-worn
operations with the back of the handset kept 10mm from the body. To maintain compliance
with FCC RF exposure requirements, use accessories that maintain a 10mm separation
distance between the user's body and the back of the handset. The use of belt clips,
holsters and similar accessories should not contain metallic components in its assembly.
The use of accessories that do not satisfy these requirements may not comply with FCC
RF exposure requirements, and should be avoided.
Taiwan NCC Warning Statement
根據低功率電波輻射性電機管理辦法
第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更
頻率、加大功率或變更原設計之特性及功能。
第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應
立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通
信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
警語:使用過度恐傷害視力。
注意事項
使用30分鐘請休息10分鐘。
未滿2歲幼兒不看螢幕，2歲以上每天看螢幕不要超過1小時。
SAR標準值2.0W/Kg；送測產品實測值為：0.159 W/Kg。
減少電磁波影響，請妥適使用
「本產品支援GSM, WCDMA FDD 900/2100 , LTE FDD
700/900/1800/2100/2600;TDD 2570~2620/2555~2655 , WLAN, BT, NFC」
使用此產品時應避免影響附近雷達系統之操作。
本設備僅供特殊軍事，工業及商業用途，不得售予一般消費者
