ILP SWP Series Manual de usuario

INSTALLATION INSTRUCTIONS

SWP LED SLIM WALL - Dark Sky ModelsPACK

CAUTION

WARNING

Introducon:

PLEASE READ INSTRUCTIONS BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCE.

Electrical products can cause death or injury, or damage to property. If in any doubt about the installaon or use of this product, consult a competent electrician.

This LED Wall-Pack uses the latest in solid-state lighng technology for long life, low maintenance, and high eﬃciency.

• This luminaire has a fixed color temperature of 3000K

• This luminaire can ﬁeld adjust the brightness through the FAO opon.

• The opcal part (LED Head) is fixed to 0° (facing down) to meet International Dark Sky Association requirements.

This luminaire can be installed with a pencil type photocell threaded through a conduit entry opening.

The solid-state driver allows operaon on nominal 120-277V / 347-480V*, 50-60Hz AC supply without any variaon in light output.

Suitable for use in the following locaons:

• Min. Ambient Temp: -40°F (-40°C)

• Max Ambient Temp: 104°F (40°C) Consult Factory For Higher Ambient

• Suitable for Wet Locaons

to meet International Dark Sky Association requirements.

Installaon Instrucons:

1. Read all Warnings and Installer Notes before proceeding with this installaon.

2. Check to ensure all parts listed are included in your installaon

* For 5L, 8L, 10L only, alternave driver to be ordered separately

Universal voltage driver permits operaon at 120-277V / 347-480V*, 50-60Hz.

0-10V control wires must be rated for 300V minimum.

For 0-10V Dimming, follow the wiring direcon as in Figure 1.

1. Connect the black ﬁxture lead to the (+) LINE supply lead.

2. Connect the white ﬁxture lead to the (-) COMMON supply lead.

3. Connect the GROUND wire from ﬁxture to supply ground. Do NOT connect the

GROUND of the dimming ﬁxture to the output.

4. Connect the violet ﬁxture lead to the (V+) Dim lead.

5. Connect the gray ﬁxture lead to the (V-) Dim lead.

To avoid the risk of ﬁre, explosion, or electric shock, this product shall be installed, inspected, and maintained by a qualiﬁed electrician, in accordance with all

applicable electrical codes.

General Wiring Diagram

Black (Line)

120-277V

347V-480V

White (Neutral)

Green (Ground)

Purple (Dim+)

Gray (Dim-)

LED DRIVER

WARNING

To avoid electric shock:

•Be certain electrical power is OFF before and during installaon or maintenance.

•Luminaire must be connected to a wiring system with equipment-grounding conductor

To avoid explosion:

•Make sure the supply voltage is the same as the rated luminaire voltage.

•Do not install where marked operang temperatures exceed the ignion temperature of the hazardous atmosphere.

•Do not operate in ambient temperatures above those indicated on the luminaire.

Figure 1

SWP LED ADJUSTABLE SLIM WALL PACK

• Use a 3/32 hexagon wrench to detach the mounng plate from the ﬁxture by unscrewing halfway the 2 side retaining screws, unl the mounng plate is loose. (Figure 1)

• Use mounng screws (not provided) to ﬁx mounng plate to the J-box (not provided). Note the screw hanging hooks should be facing out once installed. (Figure 2)

• Use a 3/32 hexagon wrench to loose the side hex screws and adjust luminaire head upward to 90 degrees. (Figure 3). NOTE: THIS ADJUSTMENT IS ONLY

USED DURING INSTALLATION. WHEN CLOSING THE ENCLOSURE, YOU MUST ROTATE THE LED HEAD BACK TO 0° (FACING DOWN).

• Open the driver box by unscrewing the top part of the driver box. (Figure 3).

• Pull out the power supply wires (L black, N White), grounding wire (G Green), and dimming wires (purple and gray) (if needed), by breaking through the 5 holes

wire gasket. (Figure 4)

• Hang the luminaire on the mounng hooks and check the internal bubble level to verify that the ﬁxture is plumb and level. (Figure 5)

Figure 1 Figure 2 Figure 3

INSTALLATION INSTRUCTIONS

Installaon Steps - Quick Install

TURN OFF POWER FROM MAIN CIRCUIT BREAKER

Loose

Figure 4 Figure 5

Wire gasket Bubble level

Maximum Torque:

1.5 N-m (13.28 in-lbs)

SWP LED ADJUSTABLE SLIM WALL PACK

INSTALLATION INSTRUCTIONS

AFTER INSTALLATION IS COMPLETE, PLEASE CHECK THE FOLLOWING:

• Ensure the lighng ﬁxture is ﬁrmly ﬁxed to the wall.

• Ensure wires are connected correctly before applying power.

• At last, turn on the power, and check if the lighng ﬁxture works properly. If not, turn oﬀ the power and contact your local dealer.

WARNING: The luminaire shall be installed by qualiﬁed electrician

Aer Installaon:

Installaon Steps - Quick Install

CAUTION: Be sure ﬁxture temperature is cool enough to touch. Do not clean or maintain while ﬁxture is energized.

1. Clean lens & ﬁxture with non-abrasive cleaning soluon.

2. Do not allow LED modules or other electronics to come into contact with water, solvents, or other chemicals

3. Clean the diﬀuser only with a mild soap and water. Do not use solvents such as alcohol or bleach.

4. Clean painted surfaces only with a mild soap, isopropyl alcohol, or acec acid soluon.

Cleaning and Maintenance:

121219

Figure 7

Figure 8

Figure 6

Tight

Figure 9

Silicone caulk

• Close and secure the driver box, by screwing back the driver box screws. Adjust back the luminaire head to downward posion. (Figure 6)

• Using the 2 top back hanging screws of the ﬁxture, temporarily hang the ﬁxture on the boom hooks of the mounng plate to safely make appropriate electrical

connecons by following the wiring diagram, use electrical connectors. Carefully tuck all the wires and connectors into the J-box. (Figure 7).

• Pull up and detach the ﬁxture. Posion it to the mounng plate using all the back top, boom and side hanging screws into the appropriate hooks of the mounng

plate (top to top, boom to boom, side to side). Secure the ﬁxture by ghtening the two side retaining screws. (Figure 8).

• Applying silicone caulk around the perimeter of the driver box where it meets the wall to ensure a water-ght seal. Finally adjust the ﬁxture head angle BACK TO

0° (FACING DOWN) and secure it by locking the side hex screw and installaon is complete. (ﬁgure 9).

TURN OFF POWER FROM MAIN CIRCUIT BREAKER

Maximum Torque:

1.5 N-m (13.28 in-lbs)

Tabla de contenidos