Ikelite 9306.35 Manual de usuario
Thank you for your purchase of Ikelite equipment. Please read this
instruction manual completely before attempting to operate or dive
with this product.
Wide Angle Port
Instruction Manual
9306.35 for Canon G15
2
Table of Contents
Specifications ..............................................................P. 3
Package Contents ......................................................P. 3
General Information ....................................................P. 3
Port Removal and Attachment ..................................P. 3
Checking the O-ring Seal ............................................P. 5
Maintenance and Storage ..........................................P. 5
Limited Warranty ........................................................P. 6
Returning Products for Service ................................P. 7
Technical Support ......................................................P. 7
Ikelite Address and Website ......................................Back Page
3
Specifications
Diameter ..........................3.0 in. (76mm)
Length ..............................1.3 in. (33mm)
Weight ..............................3.2 oz (91g)
Zoom Limitation ..............Approximately 19.1mm
Depth Rating....................200ft (60m)
General Information
This Wide Angle Port replaces the housing's original 3.9” front port and
is not removable underwater. The o-ring seal is visible through the inside
of the housing. Installation requires a strap wrench, not included.
nce the Wide Angle Port has been installed, 67mm threaded external
accessory lenses may be removed and replaced underwater.
Package Contents
- 9306.35 Wide Angle Port
- 0200 Port Cover
- Ikelite Silicone Lubricant
Port Removal and Installation
A strap wrench will be needed to remove and install ports on your Ikelite
housing.
Ikelite offers strap wrench 0945.01 through any Ikelite authorized dealer.
Lightly lubricate the port o-ring with the supplied Ikelite lubricant. D
N T use excessive lubricant which can attract debris and prevent a
good seal. Use NLY Ikelite lubricant. ther brand lubricants can cause
the o-ring to swell and not seal properly.
Port Removal
Port Installation
1. Facing the front of the housing,
place a Strap Wrench over the
housing port.
2. Tighen Strap so that the Handle is
as close to the port as possible.
3. Rotate the Handle counter-clockwise
to loosen and remove the port,
Diagram A.
4. Place the port and port o-ring in a
resealable plastic bag for storage.
1. Facing the front of the housing, attach the Wide Angle Port to the
housing by rotating port clockwise into the port hole opening until snug.
2. Place a Strap Wrench over the housing port.
3. Tighten Strap so the Handle is as close to the port as possible.
4. Rotate the Handle clockwise to tighten port, Diagram B. Tighten until a
good o-ring seal (dark circular line) can be seen from inside the housing,
Diagram C.
Diagram A
Diagram B
4
Diagram C
Handle
Handle
Strap
Strap
-ring Seal (view fr m rear f
h using with back rem ved)
Port
Port Port
5
Maintenance and Storage
After using the Wide Angle Port in water (especially saltwater), rinse with
fresh tap water and dry with a soft non-abrasive cloth. Wipe the surface
of the port lens gently with the soft non-abrasive cloth to prevent debris
buildup that can cause spotting. Use only water and a non-abrasive mild
soap solution to clean the port lens.
Caution: Do not attempt to dry the housing or port by exposing it to heat
from a hair dryer, radiator, etc. This could damage either.
Store the port in a cool, dry place with the port cover attached. Place in a
resealable plastic bag for short and long term storage.
D N T store any accessory lens attached to a housing port.
Temperature changes can make the lens hard to remove from the port
and cause accidental removal of the port.
Checking the O-ring Seal
1. After you have properly attached the Wide Angle Port and checked the o-ring
seal, replace the housing back WITH UT a camera attached.
2. Place the housing in shallow water such as a bathtub or swimming pool.
3. After a couple minutes, remove and dry the housing completely.
4. Before opening the housing, look to see if any water droplets are inside.
5. If no droplets are present, remove the housing back and check again for
droplets. If none are present, then the housing is watertight and safe for
diving. If ANY water is present inside the housing D N T dive. Repeat the
Port Removal and Installation process until no water is present.
- Before attaching a housing port, always double-check the o-ring and sealing
surfaces to make sure there is no debris present which could cause a leak.
6
This Ikelite product is warranted against any manufacturing defects for a
period of one (1) year from the original date of purchase. Defective
products should be returned to Ikelite postage paid. Ikelite will, at its sole
discretion, repair or replace such products, and will return to customer
postage paid. All other claims of any nature are not covered. Except as
mentioned above, no other warranty expressed or implied applies to this
Ikelite product.
Limited Warranty
7
Ikelite Technical Support
Email: [email protected]
Phone 317.923.4523
Fax 317.924.7988
Technical Support
Returning Products for Service (outside the nited States)
For the separate international customs documentation form that you
complete to accompany the shipment, please state or designate that the
enclosed products were originally manufactured in the USA and are
being returned to the manufacturer for repair service. Value of the
equipment listed for customs purposes should be zero.
Ikelite is most interested in performing any service to ensure that all
products perform as intended. Evidence of purchase date must be
provided to obtain warranty service.
No prior authorization is required. You may return directly to us or
through your dealer. Please include a brief description of the problem,
any relevant email correspondence, and/or instructions on what you
want us to do. Always include name, shipping address, email address,
and phone number inside of the package. Send postage paid to:
Ikelite Underwater Systems
Attenti n: Service Department
50 West 33 Street
Indianap lis, IN 46208 USA
No reimbursements for postage paid will be issued.
You may also want to insure the package.
Returning Products For Service
Ikelite nderwater Systems
50 West 33rd Street
Indianapolis, IN 46208 SA
9306.35_G15_Wide_Angle_Port_1-1112
www.ikelite.com
Tabla de contenidos
Otros manuales de Accesorios para cámaras de Ikelite
Ikelite
Ikelite ALL Manual de usuario
Ikelite
Ikelite 6182.14 Manual de usuario
Ikelite
Ikelite 6146.16 Manual de usuario
Ikelite
Ikelite 6110.91 Manual de usuario
Ikelite
Ikelite 6950.13 Manual de usuario
Ikelite
Ikelite 4061.1 DS161 Manual de usuario
Ikelite
Ikelite 6148.10 Manual de operación y mantenimiento
Ikelite
Ikelite Olympus E-3 Manual de usuario
Ikelite
Ikelite Wide Angle Port M67 Guía de inicio rápido
Ikelite
Ikelite 6870.80 Manual de usuario
Ikelite
Ikelite DLM 6” Dome Port with Zoom Manual de usuario
Ikelite
Ikelite SX10 IS Manual de usuario
Ikelite
Ikelite SLR-DC 6812.31 Manual de usuario
Ikelite
Ikelite DSC-HX20V Manual de usuario
Ikelite
Ikelite WD-4 Manual de usuario
Ikelite
Ikelite 200DLM/A Manual de usuario
Ikelite
Ikelite EOS 5D Mark II - EOS 5D Mark II 21.1MP Full Frame CMOS Digital SLR... Manual de usuario
Ikelite
Ikelite 6280.22 Manual del propietario
Ikelite
Ikelite 4080.07 Manual de usuario
Ikelite
Ikelite 6870.70 Canon EOS 70D Manual de usuario
