Ikelite 6116.18 Manual de usuario

Product Registration

Please register your product within 15 days of purchase. Our product

registration database is the quickest way for us to contact you in the

event of a product update.

To register, send a photo of the above registration label to us via

[email protected] along with your name, address, and phone

number.

Underwater Housing for Sony Cyber-shot DSC-

RX100 Mark VI, VII Digital Cameras

Product Number 6116.18

About this Product

Thank you for your purchase of Ikelite equipment. Please read this

instruction manual completely before attempting to operate or dive

with this product.

Included in the Box

• Housing

• Port cover # 0200.08

• Silicone lubricant 1cc tube

• .050” hex key # 0945.11

• 1/16” hex key # 0945.16

• 1/8” hex key # 0945.18

Specications

• 200 ft (60m) depth rating

• Controls for all camera functions except Viewnder pop-up switch

and Flash pop-up switch; Camera ash must be opened prior to

installing camera in the housing when using external strobes

• Near neutral buoyancy in fresh water

• 1/4-20 thread tray mounting with 3” (76mm) spacing

• 2.8 lb (1270 g)

• 6.1 x 5.1 x 6.8” (155 x 130 x 173 mm)

• 3.9” diameter glass lens port

Important Notices

»To prevent salt build-up and sticking controls, submerge the

empty housing in clean, freshwater. Operate the controls

several times each while underwater to ush out any residue.

»Never leave a housing in a rinse tank, even if it is the only

system in the tank. Most catastrophic oods happen when the

user walks away from a housing while it is in the rinse tank.

»Do not use alcohol, cleaning agents, spray lubricants, Rain-X,

or other solvents on the housing or lens port. Use of an

incompatible chemical compound can damage the plastic and

o-rings, and may result in leaking.

»Do not pull the shutter trigger without a camera installed. You

may accidentally detach or damage the control spring.

»Always assemble in a cool, dry location. Opening the housing

in a humid environment may cause fogging.

Contents

Product Registration 1

About this Product 2

Included in the Box 2

Specications 2

Important Notices 3

Getting to Know Your Housing 5

Accessory Port 7

Lanyard Mount 7

Setting Up Your Camera 7

Pre-Installation Checklist & Initial Camera Settings 7

Exposure Settings 8

Setting Up Your Housing 8

Opening the Housing 8

Inserting the Camera 9

Closing the Housing 10

Final Check 10

Entering the Water 11

Built-in Flash and External Strobe Use 11

About the Built-In Flash 11

Attaching a Fiber Optic Cord 12

Spare Parts 12

Maintenance 13

Post-Dive 13

Travel and Storage 13

Troubleshooting 14

Limited Warranty 16

Service and Repairs 16

Getting to Know Your Housing

Tray Mounts

Lens Port

Fiber Optic Ports

Lid Snap

Shutter Control Ring

Zoom LeverMode Dial

Accessory Port

Hole Plug

MOVIE

MENUFn

DISP / UP Cursor

MENU / SET Button

/ DOWN

Cursor

MOVIE

MENUFn

O-Ring

Lanyard Lid Hook

Control Wheel

On/off

Accessory Port

Your housing features one 1/2-20 threaded Accessory Port which

may be used for attachment of factory optional or aftermarket housing

accessories. DO NOT remove the Accessory Hole Plug unless you

are installing a compatible accessory. Visit ikelite.com for an updated

list of compatible accessories.

Lanyard Mount

The included lanyard is a break-away safety lanyard which is designed

to break of stress is placed on it. This is important so that the user can

break free if their equipment is caught on something underwater.

The lanyard is not designed to support the weight of the housing and

should not be used as a carrying strap. Carrying the housing by the

lanyard may result in damage to the lanyard and/or housing.

A different lanyard with a thin cord may be attached to the housing

using the lanyard mount on back of the housing.

Setting Up Your Camera

Pre-Installation Checklist & Initial Camera Settings

1. Insert a fully charged camera battery.

2. Insert a properly formatted memory card.

3. Set AF Illuminator to “Off.”

4. If using an external ash, set Flash Mode to “Fill-ash.”

5. Set Red Eye Reduction to “Off.”

6. Set FINDER/MONITOR to “Monitor.”

7. Set Touch Operation to “Off.”

Exposure Settings

Refer to the Cheat Sheets in the Photo School section of our website

for recommendations on exposure settings for a wide variety of

shooting situations:

https://www.ikelite.com/blogs/cheat-sheets

Setting Up Your Housing

Opening the Housing

1. Push the lid snap lock forward and start to lift the curved end away

from the housing.

2. Lid snaps are designed to provide enough force to compress the

o-ring for a proper seal. Keep rm pressure against the lid snap

while lifting it away.

Lid Snap Lock

3. Repeat with remaining lid snaps.

4. Remove the housing back.

Inserting the Camera

1. Remove any lanyard or neck strap which may be attached to the

camera.

2. Remove the camera mounting plate from the inside bottom of the

housing.

3. Pull the bottom of the rear LCD screen away from the camera body

slightly to allow for proper mounting plate alignment .

4. Line up the Mounting Screw with the Camera Tripod Socket. Use a

at head screwdriver to tighten the mounting plate to the camera.

Camera Tripod

Socket

Mounting Screw

Mounting Plate

1/4-20 Tripod

Attachment Hole

Rear LCD

Screen

5. Pull out on the housing control knobs to move them out of the way.

6. If using external strobes, raise the camera ash. The ash cannot

be raised after the camera has been installed in the housing.

7. Insert the mounting plate into the housing plate mount slot on the

inside bottom of the housing. Gently push the camera all of the way

forward until the back of the mounting plate is ush with the back of

the housing plate mount.

8. If using external strobes, check that the camera’s ash is extended

and facing the housing’s ber optic ports.

Closing the Housing

1. Make sure the o-ring is clean and in its proper location on the back

of the housing. The main o-ring does not require lubricant to make

a seal.

2. Place the back onto the housing front.

3. Make sure no controls or wires are interfering with the o-ring or the

back of the housing.

4. Place each lid snap into the corresponding hook on the housing

back.

5. Push the lid snaps towards the housing until they are at against

the housing and the lock has engaged. Close opposing lid snaps at

the same time.

6. Check the o-ring seal. The o-ring should form a uniform, solid line

around the back of the housing.

Final Check

1. Re-check the o-ring seal. The seal should form an even, solid line

around the back of the housing.

2. Turn on the camera and check all control functions.

3. Make sure that the camera can obtain focus and take a photo.

4. Check battery life and open storage space on your memory card.

5. When using strobes, check that the ash is raised.

6. Submerge the housing in a fresh water tank dedicated to

underwater photography equipment. Visually conrm that there are

no signs of water intrusion or a steady stream of bubbles coming

from one of the housing seals.

Tabla de contenidos

Otros manuales de Accesorios para cámaras de Ikelite

Ikelite

Ikelite Olympus SP-350 Manual de operación y mantenimiento

Ikelite

Ikelite 6110.91 Manual de usuario

Ikelite

Ikelite 6170.12 Manual de usuario

Ikelite

Ikelite SLR-DC 6812.31 Manual de usuario

Ikelite

Ikelite DL1 DS Link Guía de inicio rápido

Ikelite

Ikelite 6171.07 Manual de usuario

Ikelite

Ikelite 5650.01JVC Picsio GC-FM1Video Camera Manual de usuario

Ikelite

Ikelite PowerShot IXUS SD900 Ti Manual de usuario

Ikelite

Ikelite 69531 Manual de usuario

Ikelite

Ikelite 6241.26 Manual del propietario

Ikelite

Ikelite 6014.10 Manual del propietario

Ikelite

Ikelite 200DLM/A Manual de usuario

Ikelite

Ikelite Digital RebelXTi 400D Manual de operación y mantenimiento

Ikelite

Ikelite 4402 Manual de usuario

Ikelite

Ikelite 9304.53 Manual de usuario

Ikelite

Ikelite 6910.60 Manual de usuario

Ikelite

Ikelite 4405 Manual de usuario

Ikelite

Ikelite Canon PowerShot A700 Manual de usuario

Ikelite

Ikelite Canon IXUS 950 IS Manual de usuario

Ikelite

Ikelite 6871.2 Manual de usuario

Ikelite

Ikelite DSC-HX20V Manual de usuario

Ikelite

Ikelite 6251.03 Diagrama de cableado

Ikelite

Ikelite 6170.70 Manual de usuario

Ikelite

Ikelite ULTRAcompact TG-3 Manual de usuario

Manuales populares de Accesorios para cámaras de otras marcas

Viltrox

Viltrox EF-NEX Instrucciones de instalación

Calumet

Calumet 7100 Series CK7114 Manual de usuario

Ropox

Ropox 4Single Series Manual de usuario

Cambo

Cambo Wide DS Digital Series Instrucciones de funcionamiento

Samsung

Samsung SHG-120 Manual de usuario

Ryobi

Ryobi BPL-1820 Manual de operación

Aegis

Aegis ABL-36020P Manual de usuario

Pentax

Pentax Data Back Fc Manual de usuario

Fantasea

Fantasea EyeGrabber F Series Manual de usuario

Honeywell

Honeywell HDZ20HD Manual de usuario

EGO

EGO BA1400T Manual de usuario

Sima

Sima SRW-62 Manual de usuario

Shape

Shape A7SSMKIT Manual de usuario

Slide Kamera

Slide Kamera HST-2 Manual de usuario

Power works

Power works 2902613 Manual de usuario

SES

SES SE-2047-2 Manual de usuario

Olympus

Olympus PT-EP05L Manual de usuario

Starlite

Starlite OctoDome nxt Manual de usuario