Ikan MB8-2PT-KIT Manual de usuario
www.ikancorp.com 713.272.8822
CHECKED BY
QUICKSTART GUIDE
MB8-2PT-KIT
Kit with 2 x Mylo Bi-Color Half x 1 Portable Field LED Lights
What’s Included
2 x Dual Charger with Power Supply
2 x Neutral Diffusion Filter
4 x Sony Style “L” Type Batteries
2 x Half x 1 Light Fixture
2 x Power Supply with Cable
2 x Yoke Mount
2 x Stands
1 x Stand Bag
1 x Light Bag
Getting to know your MYLO lights
PRECAUTIONS:
• Keep the fixture away from water and all flammable gases or liquids.
• Use only the recommended batteries.
• Handle the unit with care.
• DO NOT attempt to disassemble or repair the unit without first contacting service department at
ikancorp.com.
• Keep the unit clean and free of dust. The unit can be cleaned with a soft dry cloth.
• Use only parts provided by the manufacture.
• Always use caution when plugging in the fixture.
Mounting the Mylo to a Stand:
The Mylo LED Light comes with a pre-installed yoke and combo mount. This allows the fixture to easily
sit and adjust on any stand. The yoke allows the light to move freely, without obstruction. The Baby 5/8"
and Junior 1-1/8" Combo Pin allows the user a wide range of stands. The light can be mounted either
horizontally or vertically on a 5/8" baby pin.
Power the LEDs:
The Mylo light comes with an included AC power supply and 6 foot cable. This allows the user to plug into
any standard 120-240v electrical outlet. The Mylo LED Light can be powered from one of two Sony “L”
Style batteries that are supplied with the unit.
Adjusting the Color & Brightness of the Light:
The Mylo LED Light is controlled by the large yellow knob on the rear of the fixture. The knob was designed
with the idea that it could be reached and adjusted when the light is up on a stand. The knob has three
push settings.
1. The default setting is the brightness from 10%-100% brightness.
2. By pressing in on the knob the color temperature can be adjusted. (Bi-Color Lights)
Mylo Battery Operation
You can charge your Sony style “L” Series DV batteries at the same time.
Connect the power cable to the AC charger and plug it into the wall.
1. Place one or both battery packs onto the charger and slide it towards the indicator lights.
2. The indicator lights will illuminate with how much charge is left on the battery.
3. The charger will begin charging when the battery is fully inserted into the charger.
(Note: The battery is fully charged when all lights are a solid red.)
Attaching the battery pack to the back of the Mylo light fixture can be done by placing the battery against
the back of the Mylo battery port and sliding it forward.
Properly store the “L” Series batteries when not in use. If the “L” Series batteries will not be used for awhile,
run down the battery and store it with the Mylo fixture.
Charging Times
Normal Charge Time Fully Charge Time
~375 min ~450 min
Be sure to charge the battery pack before you start using your Mylo Light.
We recommend charging the battery pack in an ambient temperature between 10°C~30°C (50°F~86°F)
until the charge lamps are fully lit. If you charge the battery pack outside of this temperature range, you
may not be able to charge it efficiently. Battery pack performance decreases when ambient temperature is
10°C (50°F) or below, and the length of time you can use the battery pack becomes shorter. In that case,
do the following to use the battery pack for a longer time. Put the battery pack into a pocket to warm it up,
& insert your Mylo light right before you turn it on.
About Battery Life
Battery capacity decreases over time and through repeated use. If you notice problems with the battery
keeping charge, it is probably time to replace it with a new one. Each battery’s life is governed by storage,
operating, and environmental conditions.
Specifications
Specs
Beam Angle 50°
Build Material Heavy Duty Metal Construction
Cooling System Passive Cooling
Dimming Knob Control
Fixture Power Consumption 24W; 7.4-14.8 VDC
Fixture Size 14 x 7 x 2 in.
Fixture Weight 6 lbs
Head Type Bi-Color 5600K-3200K
Lens 45°
Light Source 800 0.06 Watt LEDs
Power Supply Input: 110-240 VAC
Stand Mount Baby 5/8" Junior 1 1/8" Combo Pin
Optional Accessories
Some other products that work well with the Mylo Lights available from Ikan include:
CV600
HD-STND
ROLLR-STND10
SW-04
KCP-703
Digital LED Meter
Heavy Duty Light Stand
2 Stage Roller Stand 10 ft 6 in
Safety Wire
Stage Clamp w/ 16mm Stud
Learn More
More dynamic information at official website: www.ikancorp.com
Support
CONDITIONS OF WARRANTY SERVICE
• Free service for one year from the day of purchase if the problem is caused by manufacturing errors.
• The components and maintenance service fee will be charged if the warranty period is expired.
Free Service will not be Provided in the Following Situations:(*Even if the product is still within the warranty period.)
• Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company.
• Damage caused by natural disaster, abnormal voltage, and environmental factors, etc.
©2016 ikan Corporation. All rights reserved
Otros manuales de Equipo de DJ e iluminación/Reproductor de CD para DJ de Ikan
