IFM E30390 Manual de usuario

Operating instructions

IO-Link interface

E30390

80002691 / 02 12 / 2018

Contents

1 Preliminary note��3

1�1 Symbols used ��3

2 Safety instructions ��3

3 Functions and features ��4

3�1 Items supplied ��4

3�2 System requirements��4

3�3 Software��4

3�3�1 LINERECORDER DEVICE��4

4 Installation��5

5 Electrical connection��5

5�1 Connect sensor to a PC via the interface ��5

5�2 Power supply via an additional plug-in power supply ��6

6 Set-up ��6

7 Operation��7

8 Technical data and scale drawing��7

1 Preliminary note

Technical data, approvals, accessories and further information at www�ifm�com

1.1 Symbols used

►Instructions

> Reaction or result

[…] Designation of keys, buttons or indications

→Cross-reference

Important note

Non-compliance may result in malfunction or interference�

Information

Supplementary note

2 Safety instructions

• Read this document before setting up the product and keep it during the entire

service life�

• The product must be suitable for the corresponding applications and

environmental conditions without any restrictions�

• Only use the product for its intended purpose (→ Functions and features).

• Only use the product for permissible media (→ Technical data).

• If the operating instructions or the technical data are not adhered to, personal

injury and/or damage to property can occur�

• The manufacturer assumes no liability or warranty for any consequences

caused by tampering with the product or incorrect use by the operator�

• Installation, electrical connection, set-up, operation and maintenance of the

product must be carried out by qualified personnel authorised by the machine

operator�

• The device and the accessories (e.g. cable) must be effectively protected

against damage�

3 Functions and features

The interface connects sensors with IO-Link capability to a PC and provides the

following options via the IO-Link interface:

• Reading of the current parameter setting�

• Parameter setting of the sensor�

• Reading of the current measured values and further process values�

The interface is not suitable for permanent installation as an automation device�

3.1 Items supplied

• IO-Link interface

• USB cable

• Plug-in power supply

• M12 cable

• Operating instructions

3.2 System requirements

• PC with Microsoft Windows® 7 SP1 / Microsoft Windows® 10

• Free USB 2�0 port

• Software for parameter setting and set-up of IO-Link sensors,

LINERECORDER DEVICE:

• QA0011 (USB stick) (→ 3.3)

• QA0012 (download) (→ 3.3)

3.3 Software

The following software is suitable for use with this interface:

3.3.1 LINERECORDER DEVICE

The software LINERECORDER DEVICE is supplied with the following items:

- Framework software LINERECORDER DEVICE

- Current set of IODDs

- Driver for interface

4 Installation

You need administrator rights for installation�

►Connect the interface to the PC via a USB port�

►Connect the USB stick LINERECORDER DEVICE to the PC or use the

download version LINERECORDER DEVICE�

►Execute the installation file "ifm Software�exe"�

> The Microsoft Windows® hardware wizard is started�

►Follow the instructions in the program�

Select the following options:

- Find locally available drivers�

- Select the driver from the connected USB stick or the download version:

Current drivers can be found on the manufacturer's website�

5 Electrical connection

5.1 Connect sensor to a PC via the interface

1 2

USB

Interface

4 5321

►Connect the sensor to the interface using the M12 cable�

Socket 1 + 24 V

Socket 2 CH2 (DI/DO)

Socket 3 GND

Socket 4 IO-Link: CH1 (C/Q)

Socket 5 not connected

►Connect the interface to a PC using the USB cable�

5.2 Power supply via an additional plug-in power supply

If a sensor needs a higher current than 80 mA for a short time (e.g. at power-on)

or permanently, the power supplied via the USB port is not sufficient�

►Connect the supplied plug-in power supply to the interface�

6 Set-up

E30390

►Connect the interface to the sensor and a USB 2�0 port of the PC (→ 5)�

> After a short initialisation period the interface supplies the sensor with operating

voltage�

> If the sensor is addressed via the software LINERECODER DEVICE (→ 3.3)

the interface determines the correct communication mode and starts the

exchange of data�

If the sensor does not have a suitable communication protocol, no data is

exchanged�

7 Operation

LED Colour Status Description

PWR yellow on voltage supply via USB port

flashing undervoltage or overload with voltage

supply via USB port

CH1 (C/Q) green IO-Link mode:

flashing slowly no IO-Link connection

flashing quickly preoperate state

on IO-Link connection is exchanging data

(operate state)

yellow on switching status of the digital output

CH2 (DI/D0) yellow on switching status of the digital output

Error red on error:

(short circuit, data transmission error,

overload at DIO 1 (C/Q) or DIO 2)

8 Technical data and scale drawing

Technical data and scale drawing at www�ifm�com�

More information at www�ifm�com

Tabla de contenidos

Otros manuales de Equipo de grabación de IFM

IFM

IFM CR3130 Guía de aplicación

IFM

IFM AL1060 Manual de usuario

IFM

IFM AL1101 Manual de usuario

IFM

IFM AL1100 Manual de usuario

IFM

IFM AL1101 Manual de usuario

IFM

IFM DTC510 Manual de usuario

IFM

IFM AL1332 Manual de usuario

IFM

IFM AL1060 Manual de usuario

IFM

IFM AL1301 Manual de usuario

IFM

IFM AL1302 Manual de usuario

IFM

IFM AC1401 Guía de aplicación

Manuales populares de Equipo de grabación de otras marcas

KV2 Audio

KV2 Audio 500 Series Manual de usuario

Robotics Technologies

Robotics Technologies microBus-Cam II Manual de usuario

Seca

Seca 460 Manual de usuario

Cognex

Cognex MVS-8000 Series Manual de usuario

Mect

Mect MPNC006 Series Manual de usuario

Bad Caf

Bad Caf THE LEASH Manual de usuario

Strymon

Strymon NIGHTSKY Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario

Tews Technologies

Tews Technologies TPMC465 Manual de usuario

Honeywell

Honeywell Excel 50 Manual de usuario

SeaLevel

SeaLevel COMM+8.LPCI Manual de usuario

Arturia

Arturia AUDIOFUSE STUDIO Manual de usuario

Rukra

Rukra RK-1240 Manual de usuario

Samson

Samson SCOM Manual de usuario

Dynacord

Dynacord DPS260 Manual de usuario

Nice

Nice Core Manual de usuario

Pyle Pro

Pyle Pro PSS8 Manual de usuario

RF-System

RF-System TinyGate Manual de uso y cuidado