IFM Electronic G1501S Manual de usuario

706199 / 00 04 / 2012
Original operating instructions
Safety relay with relay outputs
G1501S
UK

2
Contents
1 Preliminary note���������������������������������������������������������������������������������������������������4
1�1 Symbols used ������������������������������������������������������������������������������������������������4
2 Safety instructions �����������������������������������������������������������������������������������������������4
3 Items supplied������������������������������������������������������������������������������������������������������6
4 Functions and features ����������������������������������������������������������������������������������������6
4�1 Requirements for the hardware configuration �����������������������������������������������7
4�1�1 Product-independent requirements ������������������������������������������������������7
4�1�2 Product-dependent requirements���������������������������������������������������������7
5 Structure and operating principle�������������������������������������������������������������������������8
5�1 Indicators and connections����������������������������������������������������������������������������8
5�2 Block diagram������������������������������������������������������������������������������������������������9
6 Installation����������������������������������������������������������������������������������������������������������10
7 Electrical connection������������������������������������������������������������������������������������������10
7�1 Supply voltage ���������������������������������������������������������������������������������������������10
7�2 Feedback contacts / monitored or automatic start��������������������������������������� 11
7�3 Output circuit������������������������������������������������������������������������������������������������12
8 Connection - Function - Fault diagnosis ������������������������������������������������������������13
8�1 Safety relay for fail-safe sensors/switches with 2 PNP outputs�������������������14
8�1�1 Connection �����������������������������������������������������������������������������������������14
8�1�2 Function����������������������������������������������������������������������������������������������15
8�1�3 Fault diagnosis �����������������������������������������������������������������������������������18
8�2 Safety relay for clocked fail-safe sensors ���������������������������������������������������20
8�2�1 Connection �����������������������������������������������������������������������������������������20
8�2�2 Function����������������������������������������������������������������������������������������������23
8�2�3 Fault diagnosis �����������������������������������������������������������������������������������24
8�3 Two-hand control using electronic sensors/switches�����������������������������������27
8�3�1 Connection �����������������������������������������������������������������������������������������27
8�3�2 Function����������������������������������������������������������������������������������������������28
8�3�3 Fault diagnosis �����������������������������������������������������������������������������������30
8�4 Two-hand control using mechanical switches with simultaneity monitoring 32
8�4�1 Connection �����������������������������������������������������������������������������������������32
8�4�2 Function����������������������������������������������������������������������������������������������34
8�4�3 Fault diagnosis �����������������������������������������������������������������������������������37

3
UK
8�5 Safety relay for mechanical switches or 2-channel fail-safe sensors/switches
with contact output and without simultaneity monitoring ������������������������������������39
8�5�1 Connection �����������������������������������������������������������������������������������������39
8�5�2 Function����������������������������������������������������������������������������������������������40
8�5�3 Fault diagnosis �����������������������������������������������������������������������������������42
9 Scale drawing ����������������������������������������������������������������������������������������������������45
10 Technical data��������������������������������������������������������������������������������������������������45
11 Tests/approvals ������������������������������������������������������������������������������������������������47
12 Terms and abbreviations����������������������������������������������������������������������������������48

4
1 Preliminary note
The instructions are part of the unit� They are intended for authorised persons
according to the EMC and Low Voltage Directive and safety regulations�
The instructions contain information about the correct handling of the product�
Read the instructions before use to familiarise yourself with operating conditions,
installation and operation�
Adhere to the safety instructions�
1.1 Symbols used
►Instructions
> Reaction, result
→Cross-reference
LED off
LED on
LED flashes
LED flashes quickly
Important note
Non-compliance can result in malfunction or interference�
Information
Supplementary note�
2 Safety instructions
• Follow the operating instructions�
• Improper use may result in malfunctions of the unit� This can lead to personal
injury and/or damage to property during operation of the machine� For this
reason note all remarks on installation and handling given in these instructions�
Also adhere to the safety instructions for the operation of the whole installation�
• In case of non-observance of notes or standards, specially when tampering
with and/or modifying the unit, any liability and warranty is excluded�
• The unit must be installed, connected and put into operation by a qualified
electrician trained in safety technology�
• The applicable technical standards for the corresponding application must be
complied with�
• For installation the requirements according to EN 60204 must be observed�

5
UK
• In case of malfunction of the unit please contact the manufacturer� Tampering
with the unit is not allowed�
• Disconnect the unit externally before handling it� Also disconnect any
independently supplied relay load circuits�
• After setup the system has to be subjected to a complete function check�
• Onlyusetheunitunderthespecifiedoperatingconditions(→10Technical
data)� In case of special operating conditions please contact the manufacturer�
• Useonlyasdescribedbelow(→4).

6
3 Items supplied
• 1 G1501S safety relay including 5 Combicon connectors with screw terminals
• 1 copy of the operating instructions safety relay, reference 704064�
If one of the above-mentioned components is missing or damaged, please contact
one of the ifm branch offices�
4 Functions and features
The safety relay is a redundant system and suited for use as:
• Safety relay for fail-safe sensors/switches with 2 PNP outputs (e�g� GM701S)�
• Safety relay for clocked fail-safe sensors (e�g� GM504S)
• Two-hand control to EN 574, type IIIC, with electronic sensors/switches
• Two-hand control to EN 574, type IIIC with mechanical switches / safety relay
for mechanical switches or 2-channel fail-safe sensors/switches (e�g� ESPE to
EN 61496-1) with contact output with simultaneity monitoring
• Safety relay for mechanical switches or 2-channel fail-safe sensors/switches
(e�g� non-contact safety devices EN 61496-1) with contact output and without
simultaneity monitoring (indefinite simultaneity)
The safe state is when the output contacts (13-14 or 23-24) are open�
ifm electronic gmbh assumes no liability for the use of units made by
external manufacturers�
Suitability of the product for a certain application cannot be assured and
must be ensured by the user�
The safety relay conforms to the category 4 according to EN 954-1 (valid until
31 December 2011), Performance Level e according to EN ISO 13849-1: 2008
as well as to the requirements SIL 3 to IEC 61508 and the classification type IIIC
according to EN 574�

7
UK
4.1 Requirements for the hardware configuration
The following requirements must be complied with when using the safety relay
G1501S:
4.1.1 Product-independent requirements
It must be ensured that the safety requirements of the respective application
correspond to the requirements stated in these instructions�
The specified technical data indicated in these instructions must be complied with�
The principle of normally closed operation must be applied to all external safety
circuits connected to the system�
By taking administrative measures in the application it must be ensured that
• the safety relays type G1501S in operation are subjected to a self-test
(switching off) within a period of maximum 12 months (intermittent operation)
• the safety-related relay contacts are protected using a suitable fuse of 3�6 A as
short-circuit / overload protection�
The self-test can be carried out by switching the supply voltage off and on or by a
safety request�
4.1.2 Product-dependent requirements
In case of faults within the safety relay which result in the defined safe state, the
safety relay must be replaced�
Any faulty unit should be returned to the manufacturer�

8
5 Structure and operating principle
5.1 Indicators and connections
A1 Supply voltage (L-, L+), function terminals (Y1, Y2)
A2 Y4, Y5, Y6, Y7: Operating mode selection, auxiliary output
A3 S33, S34, S43, S44: Connection for safety inputs / outputs
K
1 LED yellow: Triggering of the relay output channel 1
K
2 LED yellow: Triggering of the relay output channel 2
E
1 LED yellow: Input signal channel 1 or TE (for clocked sensor)
E
2 LED yellow: Input signal channel 2 or A (for clocked sensor)
Power LED green: Voltage supply
Fault LED red: Fault/start-up
C1 13, 14: Connection of relay output without delay, 1 x normally open (closed
when enabled)
C2 23, 24: Connection of relay output, 1 x normally open (closed when
enabled)

9
UK
5.2 Block diagram
POWER
INPUT CIRCUIT OUTPUT
CIRCUIT
MCU 1
(CONTROLLER)
K1
MCU 2
(CONTROLLER)
K2
Y4 Y1
L+ L- Y5 Y2
S34 S43 Y7
S33 S44
Y6
14 24
13 23

10
6 Installation
►Mount the unit on a DIN rail in a housing protected against dust and humidity
(min� IP54 - degree of soiling 2)�
7 Electrical connection
►Use 60/75°C copper conductors only�
7.1 Supply voltage
The external supply unit must have a safe separation� In case of a fault the
voltage can exceed the value of 60 V DC for a maximum of 200 ms, but
must not exceed the value of 120 V DC�
►Connect supply voltage
Manual reset
For safety reasons the unit can only be restarted by
separation from the supply voltage in case of a fault�
It is thus recommended to install a RESET switch in
series with the L+ circuit�
After power on or a RESET the unit carries out self diagnostic functions� After this
self diagnosis the unit is ready for operation�
Otros manuales para G1501S
1
Tabla de contenidos
Otros manuales de Relé de IFM Electronic

IFM Electronic
IFM Electronic ecomot200 DL0203 Manual de usuario

IFM Electronic
IFM Electronic G1501S Manual de instrucciones

IFM Electronic
IFM Electronic G1502S Manual de usuario

IFM Electronic
IFM Electronic efector 100 G1502S Manual de usuario

IFM Electronic
IFM Electronic ecomat 200 Monitor AL-3 Manual de usuario

















