IET Labs 1865-FluidTester Guía de solución de problemas

♦PRECISION INSTRUMENTS FOR TEST AND MEASUREMENT ♦

Email: inf[email protected]

TEL: (516) 334-5959 • FAX: (516) 334-5988

www.ietlabs.com

IET LABS, INC.

1865-FluidTester

Liquid Cell

User and Service Manual

1865-FLUID im/October 2013

SN: 131011542

♦PRECISION INSTRUMENTS FOR TEST AND MEASUREMENT ♦

Email: inf[email protected]

TEL: (516) 334-5959 • FAX: (516) 334-5988

www.ietlabs.com

IET LABS, INC.

WARRANTY

We warrant that this product is free from defects in material and workmanship and, when properly used,

will perform in accordance with applicable IET speciﬁcations. If within one year after original shipment,

it is found not to meet this standard, it will be repaired or, at the option of IET, replaced at no charge when

returned to IET. Changes in this product not approved by IET or application of voltages or currents greater

than those allowed by the speciﬁcations shall void this warranty. IET shall not be liable for any indirect,

special, or consequential damages, even if notice has been given to the possibility of such damages.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,

INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR

FITNESS FOR ANY PARTICULAR PURPOSE.

WARNING

OBSERVE ALL SAFETY RULES

WHEN WORKING WITH HIGH VOLTAGES OR LINE VOLTAGES.

Dangerous voltages may be present inside this instrument. Do not open the case

Refer servicing to qualiﬁed personnel

HIGH VOLTAGES MAY BE PRESENTAT THE TERMINALS OF THIS INSTRUMENT

WHENEVER HAZARDOUS VOLTAGES (> 45 V) ARE USED, TAKE ALL MEASURES TO

AVOID ACCIDENTAL CONTACT WITH ANY LIVE COMPONENTS.

USE MAXIMUM INSULATION AND MINIMIZE THE USE OF BARE

CONDUCTORS WHEN USING THIS INSTRUMENT.

Use extreme caution when working with bare conductors or bus bars.

WHEN WORKING WITH HIGH VOLTAGES, POST WARNING SIGNS AND

KEEP UNREQUIRED PERSONNEL SAFELY AWAY.

CAUTION

DO NOT APPLY ANY VOLTAGES OR CURRENTS TO THE TERMINALS OF THIS

INSTRUMENT IN EXCESS OF THE MAXIMUM LIMITS INDICATED ON

THE FRONT PANEL OR THE OPERATING GUIDE LABEL.

MEASUREMENT PROCEDURE

MEASUREMENT PREPARATIONS

1 . Conﬁrm that the electrode is washed and

cleaned.

2. Conﬁrm that a value larger than the in-

sulation resistance of a measured sample

is indicated with the insulation resistance

measured using an empty electrode. If

the measured resistance value is 1013 Ω,

it is necessary that the resistance value

measured using an empty electrode be

more than 1014 Ω. If a measured sample

insulation resistance is unknown, clean

the device so that the insulation resistance

meter used indicates the maximum value of

inﬁnity.

MEASUREMENT

1. Remove the device tightening ring, then

pour a measured sample in the electrode

twice or three times for device washing

with the measured sample liquid.

2. Pour an approximate 25 cc sample into the

device then ﬁrmly tighten ring.

3. Connect the device to the megohmmeter

with the center conductor to (+) termi-

nal, guard on cell to guard terminal, and

counter electrode to (-) terminal on the

megohmmeter using the supplied cables

and adapter.

4. Cell should be placed on insulator during

testing and should not be touched during

testing.

5. Sample volume resistivity becomes as

follows: Volume resistivity = Measured

insulation resistance from meter * Cell

Constant (Ω*cm)

6. Cell Constant is ____492______cm

Tabla de contenidos

Otros manuales de Equipo de laboratorio de IET Labs

IET Labs

IET Labs W10MT3A Manual de usuario

IET Labs

IET Labs 1408 Series Manual de usuario

IET Labs

IET Labs SRac Series Guía de solución de problemas

IET Labs

IET Labs 1232-A Guía de solución de problemas

IET Labs

IET Labs HRRS SERIES Guía de solución de problemas

IET Labs

IET Labs HARS-LX Guía de solución de problemas

IET Labs

IET Labs GenRad 1403 Series Manual de usuario

IET Labs

IET Labs 1404 Series Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario