IEI Technology WAFER-C400EV Manual de usuario

WAFER-C400EV

User Manual

Version 1.0

Low Power Intel Mobile CPU

with SVGA, LAN, USB2.0, PC-104, SBC

March 10, 2004

The information in this document is subjected to change without prior notice in

order to improve reliability, design and function and does not represent a

commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental,

or consequential damages arising out of the use or inability to use the product or

documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights

are reserved. No part of this manual may be reproduced by any mechanical,

electronic, or other means in any form without prior written permission of the

manufacturer.

Trademarks

WAFER-C400EV is a registered trademark of ICP Electronics Inc. IBM PC is a

registered trademark of International Business Machines Corporation. Intel is a

registered trademark of Intel Corporation. Other product names mentioned herein

are used for identification purposes only and may be trademarks and/or

registered trademarks of their respective companies.

Table of Contents

CHAPTER 1 INTRODUCTION.............................................................4

1.1 SPECIFICATIONS ...........................................................................5

1.2 PACKAGE CONTENTS.......................................................................6

CHAPTER 2 INSTALLATION ..............................................................7

2.1 BLOCK DIAGRAM & BOARD LAYOUT .....................................................7

2.2 UNPACKING PRECAUTIONS................................................................9

2.3 SYSTEM MEMORY DRAM .................................................................9

2.4 WATCH-DOG TIMER SETTING ............................................................9

2.5 CLEAR CMOS SETUP......................................................................9

2.6 LCD VCC VOLTAGE SELECTOR ........................................................10

2.7 SYSTEM PANEL CONNECTORS (CN9)..................................................10

CHAPTER 3 CONNECTION...............................................................11

3.1 FLOPPY DISK DRIVE CONNECTOR (FDD1) ...........................................11

3.2 PCI E-IDE DISK DRIVE CONNECTOR (IDE1).......................................12

3.3 COMPACT FLASH CONNECTOR(CN12) ................................................13

3.4 PARALLEL PORT (CN10)................................................................14

3.5 SERIAL POSTS (COM1,CN4)...........................................................15

3.6 KEYBOARD & PS/2 MOUSE CONNECTOR (CN11)...................................16

3.7 USB PORT CONNECTOR (USB1)......................................................16

3.8 IRDA INFRARED INTERFACE PORT (CN5)............................................16

3.9 VGA CONNECTOR (VGA1).............................................................17

3.10 LAN RJ45 CONNECTOR (P1,P2) .....................................................17

3.11 LCD INTERFACE CONNECTOR (CN8) .................................................18

3.12 EXTERNAL POWER CONNECTOR (CN7)................................................19

3.13 ATX POWER CONNECTOR (CN6) ......................................................19

3.14 PC/104 CONNECTION BUS (J5, J6) .................................................20

3.15 4-BIT GPIO CONNECTOR (CN1).....................................................21

3.16 FAN CONNECTOR (JFAN1) .............................................................21

3.17 AUDIO CONNECTOR (CN2).............................................................22

CHAPTER 4 AMI BIOS SETUP..........................................................23

4.1 INTRODUCTION...........................................................................23

4.2 STARTING SETUP.........................................................................23

4.3 USING SETUP.............................................................................24

4.4 GETTING HELP ...........................................................................24

4.5 MAIN MENU...............................................................................25

4.6 STANDARD CMOS SETUP ..............................................................27

4.7 ADVANCED CMOS SETUP ..............................................................28

4.8 ADVANCED CHIPSET SETUP.............................................................32

4.9 POWER MANAGEMENT SETUP...........................................................33

4.10 PCI / PLUG AND PLAY SETUP ..........................................................35

4.11 PERIPHERAL SETUP ......................................................................37

4.12 HARDWARE MONITOR SETUP ...........................................................38

4.13 CHANGE SUPERVISOR PASSWORD .....................................................39

APPENDIX A. WATCHDOG TIMER............................................................40

APPENDIX B. DIGITAL I/O.....................................................................42

APPENDIX C. I/O ADDRESS MAP............................................................43

Chapter 1 Introduction

WAFER-C400EV is designed for network applications. It supports the full functions

of an AT/ATX-compatible industrial computer on a single board. The

WAFER-C400EV is equipped with a low-power consumption and high performance

Intel Mobile processor on board. It also contains an SDRAM SODIMM socket that

support up to 512MB memory.

The WAFER-C400EV provides two Ethernet interfaces, one FDD interface, one

EIDE interface, one audio interface, one Compact Flash Type II, one parallel port,

one RS-232 serial port, one RS-232 / RS-422 / RS-485 header, one 2x25-pin LCD

header, one PC-104, two USB 2.0 ports, one 5-pin IR header, and one 6-pin

header of PS/2 keyboard/mouse interface. The built-in SVGA/LCD display

controller supports both the CRT and LCD display simultaneously. It offers the

resolutions of LCD screen up to 1024 x 768 @ 60HZ, and CRT resolutions up to

1600 x 1280 @ 64K colors. The Flash ROM contains both the system BIOS and

the VGA BIOS. Reprogramming the Flash ROM could do the modification, in case

of necessary.

1.1 Specifications

 CPU：Embedded Intel® Ultra Low Voltage Celeron 400MHz

 System Memory: One 144-pin SODIMM socket support up to 512 MB SDRAM

 BIOS: AMI 256 KB Flash memory

 Display Controller: VIA 8601T

 Support 24-bit TFT LCD panel resolution up to 1024x768 @ 60Hz

 Support non-interlaced CRT monitors resolutions up to 1600x1280 @ 16bit

colors

 IDE Interface: Supports two ATA100 IDE hard drives

 Compact Flash Disk: Runs in true IDE mode that is compatible with an IDE disk

drive. It can be used with a passive adapter in a Type II socket.

 FDD Interface: Supports up to two floppy disk drives, 5.25”（360KB and 1.2MB）

and/or 3.5”（720KB, 1.44MB, and 2.88MB）

 Serial Ports: Two RS-232 ports which COM2 can support RS-422/485

 Parallel Port: One parallel port supports SPP/EPP/ECP mode

 Audio Connector: One 2x8-pin header supports Line-in, Line-out, Speaker-out,

Mic-in.

 Digital IO: Supports four digital-in, and four digital-out

 IrDA: Supports Serial Infrared (SIR) or Amplitude Shift Keyed IR (ASKIR) interface

 PS/2 Mouse/Keyboard Connector: A 6-pin header connector supports PS/2

keyboard and PS/2 mouse.

 USB Interface: Two USB ports, USB 2.0 compliant

 Watchdog Timer: Can be set by 1-255 seconds period. Reset or NMI will be

generated when CPU does not periodically trigger the timer

 10/100Mbps Ethernet Controller: Two IEEE802.3 10/100M BASE-T standard Dual

auto-sensing interface to 10MBps or 100MBps networks. On board RJ-45 connectors

are provided for easy connection.

 PC-104 Interface: Supports ISA functions

 E2Key: A non-volatile 1Kbit EEPROM is provided to retain application critical

read/write data

 Power Supply: +5V: 3A typical, +12V: 0.1A

 Operating Temperature: 0-60℃

 Dimension: 5.9”（L）x 4.2”（W）（145mmx102mm）

1.2 Package Contents

Before any installation, please check if the following materials are included in the

package:

 One WAFER-C400EV all-in-one single board computer

 One compact disk for utility and drivers

 One 2.5" IDE flat cable (44-pin 2.0mm pitch to 40-pin 2.54mm pitch)

 One floppy cable (for 3.5" FDD only)

 One serial port cable (RS-422/485/232)

 One standard D-25 connector for parallel cable

 One 6-pin header connector for keyboard and mouse

 One audio cable

If any of these items are missing or damaged, contact your distributor or sales

representative immediately.

Chapter 2 Installation

This chapter gives instructions about how to set up the WAFER-C400EV hardware,

including directions of setting jumpers and connecting peripherals, switches and

indicators. Before installation, please pay attention to the unpacking precautions

on the following page for safety.

2.1 Block Diagram & Board Layout

 BOARD LAYOUT

 BOARD DIMENSION – SIDE VIEW

 BOARD DIMENSION

2.2 Unpacking Precautions

Some components of WAFER-C400EV SBC are very sensitive to static electric

charges and can be damaged by a sudden rush of power. To protect it from

unintended damage, be sure to note these precautions:

1. Ground yourself to remove any static charge before touching the

WAFER-C400EV SBC. You can do it by using a grounded wrist strap at all

times or by frequently touching any conducting materials that is connected

to the ground.

2. Handle WAFER-C400EV SBC by its edges. Don’t touch IC chips, leads or

circuitry if not necessary.

3. Do not plug any connector or jumper while the power is on.

2.3 System Memory DRAM

There is one 144-pin SO-DIMM socket to accept 3.3V non-buffered SDRAM. The

max Memory size is 512MB.

2.4 Watch-Dog Timer Setting

Reading port 443H enables the Watchdog Timer. It should be triggered before the

time-out period ends, otherwise it will assume the program operation is abnormal

and will issue a reset signal to start again. Reading port 043/843H disables the

Watchdog Timer. Please refer to Appendix A for detailed information.

2.5 Clear CMOS Setup

If the user needs to clear the CMOS setup (for example, the user forgot the

password, then the setup should be cleared and the password should be re-set).

The user should short the JP1 about 3 seconds, and then open it again. Opening

JP1 can set the system back to normal operation mode.

 JP1: Clear CMOS Setup (Reserve Function)

JP1 DESCRIPTION

1-2 Normal Operation

2-3 Clear CMOS Setup

Tabla de contenidos

Otros manuales de Procesador de IEI Technology

IEI Technology

IEI Technology PCISA-6770E2-RS Manual de usuario

Manuales populares de Procesador de otras marcas

FALCON THREE

FALCON THREE TV SDI Manual de usuario

Vdwall

Vdwall LVP8601 Manual de usuario

Pro ceed

Pro ceed PDP 3 Manual de usuario

Intel

Intel ARCHITECTURE IA-32 Manual de usuario

Fastwel

Fastwel CPC310 Manual de usuario

Usl

Usl JSD-60 Manual de usuario

ALLEN & HEATH

ALLEN & HEATH DR128 Manual de usuario

QSC

QSC DSP-3' Manual de referencia

Harman Kardon

Harman Kardon AVP-2 Manual de usuario

dbx

dbx Zone Pro 640 Manual de usuario

Fastwel

Fastwel CPC309 Manual de usuario

BBE

BBE 822 Manual de usuario

NAIM

NAIM AV2 Manual de usuario

GrandTec

GrandTec Grand Magic Guard III Manual de usuario

Intel

Intel 80386 Guía rápida de usuario

TECshow

TECshow DSP-2600 W Manual de usuario

Topp Music Gear

Topp Music Gear RT-DRIVE DLM-206 Manual de usuario

NEC

NEC IPS-4000 Manual de usuario