IEI Technology MMD-4300 Manual de usuario

MMD-4300 Series Medical LCD Monitor

Page i

MMD-4300 Series Medical LCD Monitor

MMD-4300 Series Medical LCD Monito

Page ii

Revision

Date Version Changes

2007-11 1.01 Modified OSD images

2007-10 1.00 Initial Release

MMD-4300 Series Medical LCD Monitor

Page iii

The information in this document is subject to change without prior notice in order to

improve reliability, design and function and does not represent a commitment on the part

of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or

consequential damages arising out of the use or inability to use the product or

documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are

reserved. No part of this manual may be reproduced by any mechanical, electronic, or

other means in any form without prior written permission of the manufacturer.

TRADEMARKS

All registered trademarks and product names mentioned herein are used for identification

purposes only and may be trademarks and/or registered trademarks of their respective

owners.

MMD-4300 Series Medical LCD Monito

Page iv

Manual Conventions

WARNING!

Warnings appear where overlooked details may cause damage to the equipment or result

in personal injury. Warnings should be taken seriously. Warnings are easy to recognize.

The word “warning” is written as “WARNING,” both capitalized and bold and is followed by

text. The text is the warning message. A warning message is shown below:

WARNING:

This is an example of a warning message. Failure to adhere to warning

messages may result in permanent damage to the MMD-4300 Series

or personal injury to the user. Please take warning messages seriously.

CAUTION!

Cautionary messages should also be heeded to help reduce the chance of losing data or

damaging the MMD-4300 Series. Cautions are easy to recognize. The word “caution” is

written as “CAUTION,” both capitalized and bold and is followed. The italicized text is the

cautionary message. A caution message is shown below:

MMD-4300 Series Medical LCD Monitor

Page v

CAUTION:

This is an example of a caution message. Failure to adhere to cautions

messages may result in permanent damage to the MMD-4300 Series.

Please take caution messages seriously.

NOTE:

These messages inform the reader of essential but non-critical information. These

messages should be read carefully as any directions or instructions contained therein can

help avoid making mistakes. Notes are easy to recognize. The word “note” is written as

“NOTE,” both capitalized and bold and is followed by text. The text is the cautionary

message. A note message is shown below:

NOTE:

This is an example of a note message. Notes should always be read.

Notes contain critical information about the MMD-4300 Series. Please

take note messages seriously.

MMD-4300 Series Medical LCD Monito

Page vi

Packing List

NOTE:

If any of the components listed in the checklist below are missing,

please do not proceed with the installation. Contact the IEI reseller or

vendor you purchased the MMD-4300 series from or contact an IEI

sales representative directly. To contact an IEI sales representative,

please send an email to [email protected].

The items listed below should all be included in the MMD-4300 Series package.

 1 x MMD-4300 Series LCD monitor

 1 x Monitor stand

 1 x Power adapter

 1 x Power cord (US)

 2 x DVI-D cables

 1 x USB cable (Type A to Type B)

 1 x User manual and utility CD

Images of the above items are shown in Chapter 3.

MMD-4300 Series Medical LCD Monitor

Page vii

Safety Precautions

 Prior to installing, moving and modifying the monitor, make sure the power is

turned off and the power cord is disconnected.

 Do not apply voltage levels that exceed the specified voltage range. Doing so will

cause fire or an electric shock.

 Electric shocks can occur if the panel is opened. Do not drop or insert any object

into the ventilation openings of the monitor.

 Only qualified engineers from certified system integrators are allowed to make

necessary functional modifications to the monitor.

 If considerable amount of dust, water or fluids entered the monitor, turn off the

power supply immediately, unplug the power cord and contact the monitor vendor.

 Explosions may occur with installations in environments where flammable gases

are present.

 Grounding reliability can only be achieved when the equipment is connected to an

equivalent receptacle marked “Hospital Only” or “Hospital Grade”.

 This device is intended to be used: (1) outside a “patient vicinity” area or (2) within

a “patient vicinity” area such as consulting rooms.

 The signal input parts or signal output parts (SIP/SOP) need to be connected

properly and any unused SIP/SOP shall not be accessible to unqualified

personnel after the LCD is integrated into a medical system.

 The unit is for exclusive interconnection with IEC 60XXX certified equipment

outside of patient environment and IEC 60601-1 certified equipment inside the

patient environment.

 This device complies with EN60601-1-2. To minimize the interference from other

equipment, a minimum 0.5 m distance shall be kept from other potential

electromagnetic sources, such as cell phones, etc.

 Equipment connected to the analog or digital interfaces must comply with the

respective IEC standards (e.g. IEC 60950 for data processing equipment and IEC

60601-1 for medical equipment).

MMD-4300 Series Medical LCD Monito

Page viii

 To fully disengage power to the unit, disconnect the power cord from its AC outlet.

Do not remove any of the display housings. There are no user serviceable parts

inside the monitor. Refer servicing to qualified service personnel.

 All configurations shall comply with the current version of the IEC 60601-1-1

safety requirements for medical electrical systems.

 To maintain the highest level of performance, it is recommended that this product

be replaced after five years of use.

FURTHER PRECAUTIONS

 Do not drop the monitor against a hard surface. Doing so will damage the display.

 Do not strike or exert excessive force onto the panel.

 Touching the LCD panel using a sharp object will cause damage to the display.

 Avoid environments exposed to direct sunlight, dust or chemical vapors.

 The ambient temperature of the installation site should be observed and

controlled to avoid overheating the monitor.

 Condensation might form inside of the monitor chassis if exposed to sudden

changes in temperature.

 Carefully route the power cord, so that people cannot step on it. Do not place

anything over the power cord or bend it.

 If the equipment should be left unused for an extended period of time, disconnect

it from the power source to avoid damage by transient over-voltage.

 If any of the following situations arise, have the equipment checked by qualified

service personnel:

o The power cord or plug is damaged.

o Liquid has penetrated into the equipment.

o The equipment has been exposed to moisture.

o The equipment does not work properly, or cannot be made to work

according to the user manual.

o The equipment has been dropped and damaged.

o The equipment shows obvious signs of damage.

MMD-4300 Series Medical LCD Monitor

Page ix

WARNING:

Any changes or modifications made to the equipment that are not

expressly approved by the relevant standards could void the authority

to operate the equipment.

ADDITIONAL INFORMATION AND ASSISTANCE

MAINTENANCE AND CLEANING

Prior to cleaning any part or component of the monitor, please read the details below.

 Except for the properly installed front LCD panel, never spray or squirt liquids

directly onto any other component. To clean the front panel, please rub it with a

piece of soft dry cloth or a slightly moistened cloth.

 The interior of the LCD monitor does not require cleaning. Keep fluids away from

the LCD monitor interior.

 Be cautious of all small removable components when vacuuming the monitor.

 Turn the system off before cleaning the LCD monitor.

 Never drop any objects or liquids through the openings of the LCD monitor.

 Be cautious of any possible allergic reactions to solvents or chemicals used when

cleaning the monitor.

 Avoid eating, drinking and smoking within vicinity of the monitor.

MMD-4300 Series Medical LCD Monito

Page x

CLEANING TOOLS

Some components in the monitor may only be cleaned using a product specifically

designed for the purpose. In such case, the product will be explicitly mentioned in the

cleaning tips. Below is a list of items to use when cleaning the computer or computer

peripherals.

 Cloth – Although paper towels or tissues can be used, a soft, clean piece of dry

cloth is recommended when cleaning the monitor.

 Using solvents – The use of solvents is not recommended when cleaning the

monitor as they may damage the plastic parts.

 Vacuum cleaner – Using a vacuum specifically designed for computers is one of

the best methods of cleaning the monitor. Over dust and dirt can restrict the

airflow in a computer and cause circuitry to corrode.

 Cotton swabs - Cotton swaps moistened with rubbing alcohol are excellent tools

for wiping hard to reach areas.

 Foam swabs - Whenever possible, it is best to use lint free swabs such as foam

swabs for cleaning.

ESD PRECAUTIONS

Observe all conventional anti-ESD methods while handling the components contained

within the LCD should the need arise for adding a functionality. The use of a grounded

wrist strap and an anti-static work pad is recommended. Avoid dust and debris or other

static-accumulating materials in the work area.

Tabla de contenidos

Otros manuales de Monitor de IEI Technology

IEI Technology

IEI Technology DM series Manual de usuario

IEI Technology

IEI Technology DM-150 Manual de usuario

IEI Technology

IEI Technology IOVU-430M Manual de usuario

IEI Technology

IEI Technology iSignager-LCD-S Series Manual de usuario

IEI Technology

IEI Technology DM-F12A/R-R10 Manual de usuario

IEI Technology

IEI Technology DM-F15A/PC-R40 Manual de usuario

IEI Technology

IEI Technology LCD-KIT Series Manual de usuario

IEI Technology

IEI Technology DM-F17A/PC-R31 Manual de usuario

IEI Technology

IEI Technology iSignager LCD 26 Manual de usuario

IEI Technology

IEI Technology TDM-121GMS Manual de usuario

IEI Technology

IEI Technology DM-F SERIES Manual de usuario

IEI Technology

IEI Technology iSignager-Frame-W07 Manual de usuario

IEI Technology

IEI Technology LCD-KIT-F Series Manual de usuario

IEI Technology

IEI Technology DM-F65A/R-R10 Manual de usuario

IEI Technology

IEI Technology iSignager 10.4 Manual de usuario

IEI Technology

IEI Technology Afolux Monitor Manual de usuario

IEI Technology

IEI Technology AFOLUX M Series Manual de usuario

IEI Technology

IEI Technology AFL M Series Manual de usuario

IEI Technology

IEI Technology S19M Manual de usuario

IEI Technology

IEI Technology DM-F65A/R Manual de usuario

IEI Technology

IEI Technology AFL-HM55 Manual de usuario

IEI Technology

IEI Technology SRM-KIT Series Manual de usuario

IEI Technology

IEI Technology DM-150GS/R-R30 Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación