Ideal Heating VOGUE MAX SYSTEM 26IE Manual de usuario

August 2021

UIN 223446 A02

When replacing any part on this appliance, use only spare parts that you can be assured conform to the safety and

performance speciﬁcation that we require. Do not use reconditioned or copy parts that have not been clearly authorised

by Ideal Heating.

For the very latest copy of literature for speciﬁcation and maintenance practices visit our website idealheating.com

where you can download the relevant information in PDF format.

HEATING

USER GUIDE

VOGUE MAX SYSTEM

15IE 18IE 26IE 32IE

15 IE G.C. Appliance No. 41-796-57

18 IE G.C. Appliance No. 41-796-58

26 IE G.C. Appliance No. 41-796-59

32 IE G.C. Appliance No. 41-796-60

THE BENCHMARK SERVICE INTERVAL RECORD MUST BE COMPLETED AFTER EACH SERVICE

Ideal Boilers is a member of the Benchmark scheme and fully supports the aims of the programme.

Benchmark has been introduced to improve the standards of installation and commissioning of central

heating systems in the UK and to encourage the regular servicing of all central heating systems to

ensure safety and efciency.

Natural Gas only

VOGUE MAX SYSTEM IE

All Gas Safe Register installers carry a Gas Safe Register ID card, and have a registration number. Both should be recorded in the

Benchmark Commissioning Checklist. You can check your installer by calling Gas Safe Register direct on 0800 4085500.

INTRODUCTION

The Vogue Max System IE is a wall mounted, room sealed, condensing system boiler, featuring full sequence automatic spark

ignition and fan assisted combustion.

Due to the high efciency of the boiler, condensate is produced from the ue gases and this is drained to a suitable disposal point

through a plastic waste pipe at the base of the boiler. A condensate ‘plume’ will also be visible at the ue terminal.

SAFETY

Current Gas Safety (Installation & Use) Regulations or rules in force.

In your own interest, and that of safety, it is the law that this boiler must be installed by a Gas Safe Registered Engineer, in

accordance with the above regulations.

In IE, the installation must be carried out by a Registered Gas Installer (RGII) and installed in accordance with the current edition

of I.S. 813 “Domestic Gas Installations”, the current Building Regulations and reference should be made to the current ETCI

rules for electrical installation.

It is essential that the instructions in this booklet are strictly followed, for safe and economical operation of the boiler.

FOR ANY QUERIES PLEASE RING THE

IDEAL CONSUMER HELPLINE : 00353 (0)1 961 7700

NOTE. BOILER RESTART PROCEDURE -

To restart the boiler, press “RESTART” hot key located below the colour screen. The appliance will now repeat

the ignition sequence if a heat demand is present.

IMPORTANT NOTES

• This appliance must not be operated without the casing correctly tted and forming an adequate seal.

• If the boiler is installed in a compartment then the compartment MUST NOT be used for storage purposes.

• If it is known or suspected that a fault exists on the boiler then it MUST NOT BE USED until the fault has been corrected by

a Gas Safe Registered Engineer or in IE a Registered Gas Installer (RGII).

•Under NO circumstances should any of the sealed components on this appliance be used incorrectly or tampered with.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they have been given supervision or instructions concerning use of the appliance

by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

In cases of repeated or continuous shutdown a Gas Safe Registered Engineer or in IE a Registered Gas Installer (RGII) should

be called to investigate and rectify the condition causing this and carry out an operational test. Only the manufacturer’s original

parts should be used for replacement.

MINIMUM CLEARANCES

Clearances of 165mm above, 100mm below, 2.5mm at the sides. The minimum front clearance when built in to a cupboard is

5mm from the cupboard door but 450mm overall clearance is still required, with the cupboard door open, to allow for servicing.

Bottom clearance

Bottom clearance after installation can be reduced to 5mm.

This must be obtained with an easily removable panel to provide the 100mm clearance required for servicing.

BOILER CONTROLS

0 4

bar

READY

TIMER OR ROOM

THERMOSTAT OFF

39OC TO CYLINDER

39°C min max

o

AB H D

A. Boiler Status

B. Burner On indication

Legend

C. Hot Keys

D. Central Heating Temp. Control

E. On / Off Control

F. Pressure Gauge

G. Hot Key Identication Text

H. Central Heating Status

TO LIGHT THE BOILER. (REFER TO BOILER

CONTROLS)

1. Switch ON electricity to the boiler and check that all

external controls, e.g. programmer and room thermostat,

are ON.

2. Set the Central Heating temperature control (D) to ‘max’.

3. Set “off/on” control (E) to “on”.

The boiler will commence the ignition sequence supplying

heat, if required.

Note. In normal operation the boiler colour screen will display

the boiler operation mode.

Boiler frost protection - boiler will re if temperature is less

than 5 degrees C.

During normal operation the burner on indicator (B) will remain

illuminated when the burner is lit.

If the boiler has not lit, after 5 ignition attempts, the following

screen will be displayed.

IGNITION LOCKOUT

Check other gas appliances work

If pre-payment meter check credit

If not, contact gas supplier

Restart boiler.

If fault persists contact installer

01482 498663

EXITRESTART

Reset the boiler and the ignition sequence will be repeated.

OPERATION

Central Heating

With the external heating controls calling for heat, the “off/on”

control (E) set to ‘on’ and the Central Heating Temperature

Control (D) turned fully clockwise, the boiler will operate to

provide heat to the system. Note this will also provide heat to

the hot water system whose temperature will be controlled by

the independent cylinder thermostat.

When the cylinder thermostat is satised the system valves

will operate to direct all ow to the Central Heating circuit. If

the cylinder thermostat calls for heat the system valves will

operate to circulate hot water around the cylinder to heat the

stored water.

Note. If the pump has not operated in the last 24 hours it will

run briey to ensure it does not become seized.

The boiler controls the central heating radiator temperature

to a maximum of 80oC, adjustable via the Central Heating

temperature control (D).

Central Heating Knob Setting Flow Temp

Minimum 30ºC

Maximum 80ºC

OVERHEAT LOCKOUT

With boiler o & system cold ﬁll System to 1.0 Bar

Bleed radiators and reﬁll system to 1.0 Bar

Check radiator valves are open.

Restart boiler.

If fault persists contact Installer

01482498660

EXITRESTART

WEATHER COMPENSATION

When the Weather Compensation option is tted to the system

then the Central Heating Temperature Control (D) becomes

a method of controlling room temperature. Turn the Central

Heating Temperature Control knob (D) clockwise to increase

room temperature and anti-clockwise to decrease room

temperature. Once the desired setting has been achieved,

leave the knob in this position and the system will automatically

achieve the desired room temperature for all outside weather

conditions.

TO SHUT DOWN THE BOILER

Set the off/on switch (E) to “off”.

TO RESTART THE BOILER

Repeat the procedure detailed in ‘To light the boiler’ (page 7).

Set the off/on control to ‘on’ and set the temperature control to

between 30ºC & 80ºC, referring to colour screen whilst adjusting.

FROST PROTECTION

If no frost protection is provided and frost is likely during a short

absence from home, leave the heating controls (if tted) at a

reduced temperature setting. For longer periods, the entire

system should be drained.

If the system includes a frost thermostat then the timer can be

left off (if tted). The mains supply should be left switched ON,

with the boiler thermostat left in the normal running position.

BOILER OVERHEAT PROTECTION

The boiler controls will shut down the boiler in the event of

overheating. Should this occur, the following screen will display:

LOSS OF SYSTEM WATER PRESSURE

The gauge (F) indicates the central heating system pressure. If the pressure is seen to fall below the original installation pressure

of 1.0 & 1.5 bar and the above screen is displayed then conduct the re-pressurising procedure as follows:

Re-pressurise via the lling loop to between 1.0 & 1.5 bar (if unsure contact your installer), turn off the tap on the lling loop.

Press “RESTART” hot key on the control panel to restart the boiler. If unable to do so or if the pressure continues to drop a

Gas Safe Registered Engineer or in IE a Registered Gas Installer (RGII) should be consulted.

THE BOILER WILL NOT OPERATE IF THE PRESSURE HAS REDUCED TO LESS THAN 0.5 BAR UNDER THIS CONDITION.

In this case the following display will appear:

EXIT

LOW WATER PRESSURE

With boiler o & system cold

ﬁll system to between 1.0 & 1.5 bar

Bleed radiators then reﬁll.

If fault persists contact Ideal (01482 498660)

If pressure loss re-occurs contact installer

CONDENSATE DRAIN

This appliance is tted with a siphonic condensate trap

system that reduces the risk of the appliance condensate

from freezing. However should the condensate pipe to this

appliance freeze, please follow these instructions:

a. If you do not feel competent to carry out the defrosting

instructions below please call your local Gas Safe

Registered installer for assistance or in IE a Registered

Gas Installer (RGII).

If you do feel competent to carry out the following instructions

please do so with care when handling hot utensils. Do not

attempt to thaw a condensate drain pipe if you cannot reach it

from ground level. Be aware that any water used can quickly

freeze if it falls onto pathways, causing a possible slip hazard.

If this appliance develops a blockage in its condensate

pipe, its condensate will build up to a point where the

burner will go out:

IGNITION LOCKOUT

Check other gas appliances work

If pre-payment meter check credit

If not, contact gas supplier

Restart boiler.

If fault persists contact installer

01482 498663

EXITRESTART

If the appliance is restarted it will not light prior to it locking

out, displaying the above.

To unblock a frozen condensate pipe;

1. Follow the routing of the plastic pipe from its exit point on

the appliance, through its route to its termination point.

Locate the frozen blockage. It is likely that the pipe is

frozen at the most exposed point external to the building

or where there is some obstruction to ow. This could be

at the open end of the pipe, at a bend or elbow, or where

there is a dip in the pipe in which condensate can collect.

The location of the blockage should be identied as

closely as possible before taking further action.

2. Apply a hot water bottle, microwaveable heat pack or a

warm damp cloth to the frozen blockage area. Several

applications may have to be made before it fully defrosts.

Warm water can also be poured onto the pipe from a

watering can or similar. DO NOT use boiling water.

3. Caution when using warm water as this may freeze and

cause other localised hazards.

Once the blockage is removed and the condensate can ow

freely, restart the appliance. (Refer to “To Light the boiler”)

5. If the appliance fails to ignite, call your Gas Safe

Registered engineer.

Preventative solutions

During cold weather, set the boiler stat to maximum, (must

return to original setting once cold spell is over).

Place the heating on continuous and turn the room stat down

to 15ºC overnight or when unoccupied (return to normal after

cold spell).

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Caldera de Ideal Heating

Ideal Heating

Ideal Heating III Series Manual del propietario

Ideal Heating

Ideal Heating LOGIC COMBI2 C24 Manual de usuario

Ideal Heating

Ideal Heating LOGIC COMBI2 C24 Guía del usuario

Ideal Heating

Ideal Heating VOGUE MAX COMBI 40IE Manual de usuario

Ideal Heating

Ideal Heating LOGIC SYSTEM S15IE Guía del usuario

Ideal Heating

Ideal Heating LOGIC MAX SYSTEM2 S15 Manual de usuario

Ideal Heating

Ideal Heating LOGIC SYSTEM 2 S15 Guía del usuario

Ideal Heating

Ideal Heating Keston COMBI2 C30 Guía del usuario

Ideal Heating

Ideal Heating EVOMAX 2 Manual de usuario

Ideal Heating

Ideal Heating IMAX XTRA 2 Manual de usuario

Ideal Heating

Ideal Heating LOGIC+ COMBI C35 Guía del usuario

Ideal Heating

Ideal Heating LOGIC MAX COMBI 2 C24 Guía del usuario

Ideal Heating

Ideal Heating LOGIC MAX HEAT2 H12 Manual de usuario

Ideal Heating

Ideal Heating LOGIC HEAT2 H12 Manual de usuario

Ideal Heating

Ideal Heating LOGIC MAX SYSTEM2 S15 Guía del usuario

Ideal Heating

Ideal Heating VOGUE MAX SYSTEM 32IE Guía del usuario

Ideal Heating

Ideal Heating EVOMAX 2 Series Manual de usuario

Ideal Heating

Ideal Heating LOGIC MAX HEAT H 12IE Manual de usuario

Ideal Heating

Ideal Heating LOGIC SYSTEM S18IE Manual de usuario

Ideal Heating

Ideal Heating LOGIC SYSTEM 2 S15 Manual de usuario

Ideal Heating

Ideal Heating i-mini C24 Manual de usuario

Ideal Heating

Ideal Heating MONARCH 30 Manual de instrucciones

Ideal Heating

Ideal Heating LOGIC HEAT2 H12 Guía del usuario

Ideal Heating

Ideal Heating LOGIC MAX COMBI 2 C24 Manual de usuario

Manuales populares de Caldera de otras marcas

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manual de usuario

Radijator

Radijator BIO max 23.1 Manual de usuario

Brunner

Brunner BSV 20 Manual de usuario

Buderus

Buderus Logamax GB062-24 KDE H V2 Manual de usuario

Potterton

Potterton 50e Hoja de datos

UTICA BOILERS

UTICA BOILERS TriFire Manual de usuario

Joannes

Joannes LADY Series Manual

ECR International

ECR International UB90-125 Manual de instrucciones

Froling

Froling FHG Turbo 3000 Manual de usuario

Froling

Froling P4 Pellet 8 - 105 Manual de usuario

U.S. Boiler Company

U.S. Boiler Company K2 Manual de usuario

Henrad

Henrad C95 FF Manual de usuario

NeOvo

NeOvo EcoNox EF 36 Manual de usuario

Potterton

Potterton PROMAX SL 12 Manual de usuario

Eco Hometec

Eco Hometec EC 25 COMPACT Manual de usuario

Viessmann

Viessmann VITODENS 200 Guía

Baxi

Baxi Prime 1.24 Manual de usuario

REXNOVA

REXNOVA ISA 20 BITHERMAL Manual de usuario