Icom IC-910H Instrucciones de funcionamiento

PROGRAMMING GUIDE

5-t5-

one

sign

ling

Table of Contents

Five-Tone Programming.........................................................................................................................................1

Programming for 5-Tone Calls with no ID (Muted System)................................................................................1

Programming for 5-Tone Calls with Open Mic....................................................................................................3

Programming for 5-Tone Calls with PTT ID (Muted System)............................................................................. 5

Programming 5-Tone non-selective transmissions with PTT ID (Unmuted System)......................................... 7

Programming for 5-Tone Emergency with ID......................................................................................................9

Programming Kill/Stun/Revive in 5-Tone..........................................................................................................11

Programming PTT ID with DTMF Tone ID in 5-Tone........................................................................................13

Programming Select Call with DTMF in 5-Tone................................................................................................15

Programming Short Messages in 5-Tone .........................................................................................................17

Five-Tone Program Settings.................................................................................................................................19

5Tone RX Code CH Window.............................................................................................................................19

5Tone RX Code Setting Window.......................................................................................................................20

5Tone TX Code CH Window.............................................................................................................................20

5Tone TX Code Setting Window.......................................................................................................................21

Format Window .................................................................................................................................................22

User Tone Window............................................................................................................................................22

Five-Tone Programming

Note: Each 5-tone feature is written with the TX and RX programming separate. In most cases, each radio will

have both the RX and TX parameters programmed in, but the guide describes the programming separately to

avoid confusion.

Programming for 5-Tone Calls with no ID (Muted System)

This procedure enables you to call a particular radio (selective call). The receive radio will receive your call but

will be unable to tell the identity of the TX radio. Receiving radios are muted to all traffic unless the call is

accompanied by the transmitting radio’s 5-tone ID.

The following instructions assume that frequencies, tones, and squelch are set and the radios are in PMR mode

(found in the Menu bar under Model). Additionally, the Auto Reset Timer must be enabled (Memory CH) and a

value entered (Common -> Common). These instructions apply to all Icom radios with PMR capability.

TX Radio:

Memory Ch

Field

Setting / Description

CH Mute

Mute options depend on radio model:

Cont (not muted) or SGL (muted until call is received)

Or (not muted) or AND (muted until call is received)

Switch Action » Call Set to Audible

5Tone Signaling » Form

Set to EIA

5Tone Signaling »STN Set to 1. Points to 1

line in the TX Code CH window: target

Radio’s 5 Tone code

TX Code CH (under 5 Tone):

Field

Setting / Description

Line 1

Target radio ID

Line 2, 3…

5-tone for multiple target radios

Key and Display (under Common)

Field

Setting / Description

Key » P0-P3

Assign a key (right-click Conventional field to access

menu) for the following functions:

TX Code CH Select— Enters the Code Select mode so

that you can select a target radio from the TX Code

Channel list.

TX Code CH Up—Allows you to scroll through the target

radio list and select a radio. (As an alternative, you can

also use the Up/Down keys to scroll.)

Call—Sends the 5-tone signal to the target radio.

2 © June 2011 Icom America

To Make a call

To call a specific radio (selective call):

1. Press the assigned TX Code CH Select key to enter the select mode.

2. Press the assigned TX Code Up key (or up/down keys) to scroll and select the target radio.

3. Press the assigned Call key. This sends the target radio’s 5-tone code.

RX Radio:

Memory Ch

Field

Setting / Description

5Tone Signaling » Form

Set to EIA

5Tone Signaling »RX C.No Set to 1. Points to 1

line in the RX Code CH window: the

RX Radio’s ID.

RX Code CH (under 5 Tone)

Field Setting / Description

Line 1 » RX Code

This particular radio’s RX ID.

Programming for 5-Tone Calls with Open Mic

This procedure enables you to call a particular radio (selective call) and listen with the RX radio mic open for a

pre period of time.

The following instructions assume that frequencies, tones, and squelch are set and the radios are in PMR mode

(found in the Menu bar under Model). These instructions apply to all Icom radios with PMR capability.

TX Radio:

Memory Ch

Field

Setting / Description

CH Mute

Mute options depend on radio model:

Cont (not muted)

Or (not muted)

Switch Action » Call Set to Audible

5Tone Signaling » Form

Set to EIA

5Tone Signaling »STN Set to 1. Points to 1

line in the TX Code CH window: target

Radio’s 5 Tone code

TX Code CH (under 5 Tone):

Field

Setting / Description

Line 1

Target radio ID

Line 2, 3…

5-tone for multiple target radios

Key and Display (under Common)

Field

Setting / Description

Key » P0-P3

Assign a key (right-click Conventional field to access

menu) for the following functions:

TX Code CH Select— Enters the Code Select mode so

that you can select a target radio from the TX Code

Channel list.

TX Code CH Up—Allows you to scroll through the target

radio list and select a radio. (As an alternative, you can

also use the Up/Down keys to scroll.)

Call—Sends the 5-tone signal to the target radio.

Common (under Common):

Field

Setting / Description

Auto Reset »Timer B

This timer sets how long mute will be open (and other reset

functions). Set to 10 sec, or as desired.

4 © June 2011 Icom America

To Make a call

To call a specific radio (selective call):

1. Press the assigned TX Code CH Select key to enter the “select” mode.

2. Press the assigned TX Code Up key (or up/down keys) to scroll and select the target radio.

3. Press the assigned Call key. This sends the target radio’s 5-tone code.

RX Radio:

Memory Ch

Field

Setting / Description

5Tone Signaling » Form

Set to EIA

5Tone Signaling »RX C.No Set to

. Points to 1

line in the RX Code CH window: the

RX Radio’s open mic code.

RX Code CH (under 5 Tone)

Field

Setting / Description

Line 1 » RX Code

This radio’s open mic ID (from the Memory Ch window).

When the RX radio sees this, it will respond accordingly.

Line 1 » Auto TX Set to ON to enable open mic (setting not available on

F3021 series radios)

Common (under Common)

Field

Setting / Description

Auto TX Timer

Sets how long the mic stays open. Default is 60 seconds.

(setting not available on F3021 series radios)

Programming for 5-Tone Calls with PTT ID (Muted System)

This procedure enables you to call a particular radio and send your radio’s numeric ID. The receive radio will

receive your call and your numeric ID will appear on its display. Radios will hear only traffic directed to that

particular radio.

The following instructions assume that frequencies, tones, and squelch are set and the radios are in PMR mode

(found in the Menu bar under Model). Additionally, the Auto Reset Timer must be enabled (Memory CH) and a

value entered (Common -> Common). These instructions apply to all Icom radios with PMR capability.

TX Radio:

Memory Ch

Field

Setting / Description

CH Mute

Mute options depend on radio model:

SGL (muted until call is received)

AND (muted until call is received)

Switch Action » Call

Set to Audible

5Tone Signaling » Form

Set to EIA

5Tone Signaling »STN Set to 1. Points to 1

line in the TX Code CH window: target

Radio’s 5 Tone code

5Tone Signaling »ID

Set a line to TX radio’s ID code (this radio)

5Tone Signaling »POS Set to BTM (Sends STN and ID codes together.)

TX Code CH (under 5 Tone):

Field

Setting / Description

Line 1

Target radio ID

Line 2, 3…

5-tone for multiple target radios

Line 28 TX radio ID (this radio’s ID) This ID is sent along with the

target radio ID

Key and Display (under Common)

Field

Setting / Description

Key » P0-P3

Assign a key (right-click Conventional field to access

menu) for the following functions:

TX Code CH Select— Enters the Code Select mode so

that you can select a target radio from the TX Code

Channel list.

TX Code CH Up—Allows you to scroll through the target

radio list and select a radio. (As an alternative, you can

also use the Up/Down keys to scroll.)

Call—Sends the 5-tone signal to the target radio.

6 © June 2011 Icom America

To Make a call

To call a specific radio (selective call):

1. Press the assigned TX Code CH Select key to enter the “select” mode.

2. Press the assigned TX Code Up key (or up/down keys) to scroll and select the target radio.

3. Press the assigned Call key. This sends the target radio’s 5-tone code.

RX Radio:

Memory Ch

Field

Setting / Description

5Tone Signaling » Form

Set to EIA

5Tone Signaling »RX C.No

Set to 1. Points to 1st line in the RX Code CH window: the

RX Radio’s open mic code.

RX Code CH (under 5 Tone)

Field

Setting / Description

Line 1 » RX Code

This radio’s ID

Line 1 » ID Dec

Set to ON. This allows the radio to show the TX radio ID.

RX Code Setting (under 5 Tone)

Field

Setting / Description

Timer

ID Decode

Set to 1.6

TX Code Setting (under 5 Tone)

Field

Setting / Description

Timer » Displayed Digit

Enter the digits you want displayed. For example: Send

98765, but if you only want 765

to show on this radios

display, enter “345”. Now the last 3 digits of any 5 tone ID

will be displayed.

Programming 5-Tone non-selective transmissions with PTT ID (Unmuted System)

This procedure enables you to send your radio’s ID when pressing PTT. The receive radio(s) will receive your

transmission and your ID will appear on its display. Radios will hear all other traffic also

The following instructions assume that frequencies, tones, and squelch are set and the radios are in PMR mode

(found in the Menu bar under Model). Additionally, the Auto Reset Timer must be enabled (Memory CH) and a

value entered (Common -> Common). These instructions apply to all Icom radios with PMR capability.

TX Radio:

Memory Ch

Field

Setting / Description

CH Mute

Mute options depend on radio model:

Cont (not muted)

Or (not muted)

Switch Action

Call

Set to Audible

Log-In/Off

Set to activate PTT ID by pressing (log in) or releasing (log

off) the PTT key

5Tone Signaling » Form Set to EIA

5Tone Signaling »ID

Set to 28. Points to 28th line in the TX Code CH window:

target Radio’s 5 Tone code. You can use any line, but

setting to line 28 allows you to use lines 1-27 for other call

features.

TX Code CH (under 5 Tone):

Field

Setting / Description

Line 28 Enter this radio’s ID.

This ID will always be a 5-digit number ending in the same

number for all the radios in the system. This allows all

radios to recognize each radio’s PTT ID (see RX Code CH).

8 © June 2011 Icom America

To Make a call

Press PTT to send the tone. The TX PTT ID will flash continuously on the RX radio(s).

RX Radio:

Memory Ch

Field

Setting / Description

5Tone Signaling » Form Set to EIA

5Tone Signaling »RX C.No Set to 1. Points to 1

line in the RX Code CH window: This

is where the RX radio sees the TX Radio’s ID.

RX Code CH (under 5 Tone)

Field

Setting / Description

Line 1 » RX Code Enter ++++9. The +’s are wildcards, allowing the radio to

see any first 4 digits. The “9” is the qualifier (0-8 will work

also). This last digit must match the same last digit of the TX

radio ID.

Line 1 » ID Dec

Set to ON. This allows the radio to show the TX radio ID.

RX Code Setting (under 5 Tone)

Field

Setting / Description

Timer » Compare Digit Enter the digits you want displayed. For example: Send

98769, but if you only want 9876

to show on this radio’s

display, enter 1234. Now the first 4 digits of any 5 tone ID

will be displayed.

Otros manuales para IC-910H

Tabla de contenidos

Otros manuales de Radio bidireccional de Icom

Icom

Icom IC-GM1600E Manual de usuario

Icom

Icom IC-GM1500 Manual de usuario

Icom

Icom IC-703 Plus Manual de usuario

Icom

Icom IC-FR3000 Series Manual de usuario

Icom

Icom IC-V80E Instrucciones de instalación y funcionamiento

Icom

Icom IC-F1020 Manual de usuario

Icom

Icom IC-2SA Manual de usuario

Icom

Icom IP100H Manual de usuario

Icom

Icom IC-GM1600E Manual de usuario

Icom

Icom UT-109 Manual de usuario

Icom

Icom CS-F14 Manual de usuario

Icom

Icom IC-F1500 Manual de usuario

Icom

Icom Two-Way Radios Manual de instrucciones

Icom

Icom IC-2200H Instrucciones de instalación y funcionamiento

Icom

Icom IC-775DSP Manual de funcionamiento

Icom

Icom ID-800H Instrucciones de instalación y funcionamiento

Icom

Icom IC-F620 Instrucciones de montaje

Icom

Icom IC-A24 Manual de usuario

Icom

Icom IC-A23 Guía del administrador

Icom

Icom IP100H Manual de usuario

Icom

Icom IC-F3 Manual de usuario

Icom

Icom UT-111 Manual de usuario

Icom

Icom IC-GM1600E Manual de usuario

Icom

Icom IC-F3001 Manual de usuario

Manuales populares de Radio bidireccional de otras marcas

Midland

Midland 70-1526A/B Manual de usuario

HYT

HYT TC700 Manual de usuario

DNT

DNT Space100 Manual de usuario

Legacy

Legacy ProLine Series Manual de usuario

Evolveo

Evolveo FreeTalk XM2-2 Manual de usuario

AWC

AWC AWR1688+ Manual de usuario

Motorola

Motorola XT665d Manual de usuario

Cobra

Cobra 2-Way Radio Manual de usuario

Klutch

Klutch KR-400 Manual de usuario

Garmin

Garmin Rino 655t Manual de usuario

Motorola

Motorola TLK 150 Manual de usuario

Midland

Midland MXT275J Manual de usuario

Titan

Titan TR200 Manual de usuario

Cobra

Cobra CXT645 Manual de usuario

Tait

Tait TM9100 Manual de usuario

Yaesu

Yaesu FT-65R Manual de usuario

RELM

RELM RP3000 Manual de usuario

Motorola

Motorola ASTRO SRX 2200 Series Manual de usuario