Icom IC-V86 Guía de configuración

13 OPTIONS

12 TROUBLESHOOTING

11 RESETTING

10 PROGRAMMING

9 SET MODES

8 DTMF MEMORY

TONE SQUELCH AND POCKET BEEP

6 SCAN OPERATION

5 MEMORY/CALL OPERATION

REPEATER AND DUPLEX OPERATION

3 ADVANCED OPERATION

2 BATTERY CHARGE

1 ACCESSORIES

INTRODUCTION

ADVANCED MANUAL

VHF TRANSCEIVER

|V86

INTRODUCTION

Thank you for choosing this Icom product. This

product was designed and built with Icom’ s state of

the art technology and craftsmanship. With proper

care, this product should provide you with years of

trouble-free operation.

IMPORTANT

READ ALL INSTRUCTIONS carefully and completely

before using the transceiver.

SAVE THIS INSTRUCTION MANUAL — This

instruction manual contains advanced operating

instructions for the IC-V86. For basic operating

instructions, see the BASIC MANUAL.

FEATURES

zRugged construction (IP54* and MIL-STD-810G)

zPowerful 7.0 W of output power (Extra High power)

zExtend Battery Life function (With the BC-240)

* Only when the battery pack or case, antenna, and jack

cover are attached.

Icom, Icom Inc. and the Icom logo are registered

trademarks of Icom Incorporated (Japan) in Japan,

the United States, the United Kingdom, Germany,

France, Spain, Russia, and/or other countries.

All other products or brands are registered trademarks

or trademarks of their respective holders.

Icom is not responsible for the destruction, damage

to, or performance of any Icom or non-Icom

equipment, if the malfunction is because of:

• Forcemajeure,including,butnotlimitedto,res,

earthquakes,storms,oods,lightning,other

natural disasters, disturbances, riots, war, or

radioactive contamination.

•The use of Icom transceivers with any equipment

that is not manufactured or approved by Icom.

1-1

Section 1ACCESSORIES

Supplied Accessories .............................................................................1-2

Antenna ..................................................................................................1-2

Belt clip...................................................................................................1-2

Battery pack or case...............................................................................1-3

Jack cover ..............................................................................................1-3

1ACCESSORIES

1-2

Supplied Accessories

Battery pack*

Jack cover

(with screws)

Battery charger*

Belt clip

Power adapter*

Antenna*

* Not supplied, or the shape is different, depending on

the transceiver version.

Antenna

Insert the antenna into the antenna connector and

twist the antenna base to lock it in place.

CAUTION:

•NEVER HOLD just the antenna when carrying the

transceiver.

•DO NOT transmit without an antenna.

Belt clip

To attach the belt clip:

zSlide the belt clip in the direction of the arrow until

the belt clip locks in place, and makes a ‘click’

sound.

Belt clip

Battery pack/case

To detach the belt clip:

1. Remove the battery pack or case from the

transceiver, if it is attached.

2. Lift the tab up (1), and slide the belt clip in the

direction of the arrow (2).



1ACCESSORIES

1-3

Battery pack or case

CAUTION: When the battery case is attached, the

Battery Protection function must be turned OFF in

the Initial Set mode. (p. 9-7)

To attach the battery pack or case:

1. Insert the battery pack or case in the direction of

the arrow (1), then close.

2. Hook the latch until it makes a ‘click’ sound (2).



Battery pack/case

Latch

To remove the battery pack or case:

RWARNING! The latch is tightly locked, so use

caution when releasing it. DO NOT use your

ngernail.Usetheedgeofacoinorscrewdrivertip

to carefully release it.

zUnhook the latch (1), and then lift up the battery

pack or case in the direction of the arrow (2).





CAUTION: NEVER remove or attach the battery

pack or case when the transceiver is wet or soiled.

This may result in water or dust getting into the

transceiver or the battery pack or case, and may

result in them being damaged.

NOTE: Keep battery terminals clean. It’s a good idea

to occasionally clean them.

Jack cover

Attach the jack cover when optional equipment is not

used.

To attach the jack cover

1. Attach the jack cover

to the [SP MIC] jack

(1).

2. Insert and tighten the

screws (2).

To detach the jack cover

1. Remove the screws

with a phillips

screwdriver (1).

2. Detach the jack cover

to connect optional

equipment (2).





2-1

Section

Battery chargers .....................................................................................2-2

DUsing the BC-191 to rapid charge the BP-264 ...............................2-2

DUsing the BC-192 to regular charge the BP-264 ............................2-2

DUsing the BC-240 to rapid charge the BP-298/BP-299 ..................2-3

Optional battery case (BP-263) ..............................................................2-4

2BATTERY CHARGE

2-2

DUsing the BC-191 to rapid charge

the BP-264

The BC-191 provides rapid charging of only the

BP-264 Ni-MH battery pack. Never use it to charge

any other battery pack.

Charging time: Approximately 2 hours

The following item is additionally required:

A power adapter (not supplied with some transceiver

versions) or the OPC-515L or CP-23L DC power cable.

DUsing the BC-192 to regular charge

the BP-264

The BC-192 provides regular charging of only the

BP-264 Ni-MH battery pack. Never use it to charge

any other battery pack.

Charging time: Approximately 16 hours

The following item is additionally required:

A power adapter (not supplied with some transceiver

versions) or the OPC-515L DC power cable.

The optional OPC-

515L (for a DC power

source) or CP-23L

(for a 12 V cigarette

lighter socket) can be

used instead of the

power adapter.

Power adapter

(

A different type, or no power

adapter is supplied, depending

on the transceiver version.

)

Using screws are

recommended to

secure the charger.

Charging indicator

•Lights orange: While charging

•Lights green: When charging is completed.

Screws*

(Self tapping screw:

M3.5 × at least 30 mm)

* User supplied

Battery pack + Transceiver

Turn OFF

Battery pack

The optional OPC-515L

(for a DC power source)

can be used instead of

the power adapter.

Power adapter

(

A different type, or no power

adapter is supplied, depending

on the transceiver version.

)

Battery pack + Transceiver

Battery pack

Turn OFF

Using screws are

recommended to

secure the charger.

Screws*

(Self tapping screw:

M3.5 × at least 30 mm)

* User supplied

Charging indicator

•Lights green while charging.

NOTE:

The charge indicator will not go

out even after a battery pack is

fully charged.

Charging time period differs,

depending on the input voltage.

12 V: Approximately 36 hours

13.8 V: Approximately 21 hours

16 V: Approximately 16 hours

Battery chargers

2BATTERY CHARGE

2-3

DUsing the BC-240 to rapid charge

the BP-298/BP-299

The BC-240 provides rapid charging of only the

BP-298/BC-299 Li-ion battery pack. Never use it to

charge any other battery pack.

Charging time*

with the BP-298: Approximately 3 hours

with the BP-299: Approximately 4.6 hours

* When the Extend Battery Life function is turned OFF.

See the BASIC MANUAL for details.

The following item is additionally required:

A power adapter (not supplied with some transceiver

versions) or the OPC-515L or CP-23L DC power cable.

CAUTION: When using the OPC-515L DC power

cable NEVER connect the OPC-515L to a power

source using reverse polarity. This will ruin the

battery charger. White line:

Black line:

–

The optional OPC-515L

(for a DC power source)

or CP-23L (for a 12 V

cigarette lighter socket)

can be used instead of

the power adapter.

Power adapter

(

A different type, or no power

adapter is supplied, depending

on the transceiver version.

)

Battery pack + Transceiver

Battery pack

Turn OFF

Using screws are

recommended to

secure the charger.

Screws*

(Self tapping screw:

M3.5 × at least 30 mm)

* User supplied

Charging indicator

•Lights orange: While charging

•Lights green: When charging is completed.

•Blinks red: When a charging error has

occurred.

Battery chargers

2BATTERY CHARGE

2-4

Optional battery case (BP-263)

When using the battery case (BP-263), install 6 × AA

(LR6) size alkaline batteries, as described below.

Remove the battery case, if it is attached. (p. 1-3)

Install 6 × AA (LR6) size alkaline batteries.

Install only alkaline batteries.

Be sure to observe the correct polarity.

Attach the battery case. (p. 1-3)

CAUTION:

•When installing batteries, make sure they are all

the same brand, type and capacity. Also, do not

mix new and old batteries together.

•Keep battery terminals clean. It’s a good idea to

occasionally clean them.

•Never incinerate used battery cells since the

internal battery gas may cause them to rupture.

•Never expose a detached battery case to water.

If the battery case gets wet, be sure to wipe it dry

before using it.

•Never use batteries whose insulated covering is

damaged.

BE CAREFUL! The negative

terminals of the battery case

protrude from the body, so

pay attention not to injure your

ngerswheninsertingthe

batteries.

3-1

Section

Adjusting the audio level.........................................................................3-2

Selecting passband width.......................................................................3-2

Receiving................................................................................................3-2

Transmitting............................................................................................3-2

[VOL] function assignment .....................................................................3-3

Weather channel operation (For only the USA version) .........................3-4

DWeather channel selection..............................................................3-4

DWeather Alert function.....................................................................3-4

3ADVANCED OPERATION

Tabla de contenidos

Otros manuales de Transceptor de Icom

Icom

Icom IDAS IC-F3210D Manual de usuario

Icom

Icom IC-T70A Manual de usuario

Icom

Icom IC-F110 Manual de usuario

Icom

Icom IC-F8100 Manual de usuario

Icom

Icom IC-2820H Manual de usuario

Icom

Icom IC-245E Manual de usuario

Icom

Icom IC-V3MR Manual de usuario

Icom

Icom IC-440 Manual de usuario

Icom

Icom IC-01AT Manual de usuario

Icom

Icom IC-905 Guía de configuración

Icom

Icom IC-M801E Manual de usuario

Icom

Icom ic-m423g Manual de usuario

Icom

Icom VHF IC-F50 Manual de usuario

Icom

Icom IC-F70DT Manual de usuario

Icom

Icom IC-A16E Guía de instalación

Icom

Icom IC-F3002 Manual de usuario

Icom

Icom IC-M700TY Manual de usuario

Icom

Icom IC-F21 Manual de usuario

Icom

Icom IC-iF9511HT Manual de usuario

Icom

Icom IC-F3162DT Manual de usuario

Icom

Icom IC-781 Manual de usuario

Icom

Icom IC-M24 Manual de usuario

Icom

Icom IC-M11 Manual de usuario

Icom

Icom iM506 Manual de usuario

Manuales populares de Transceptor de otras marcas

Yaesu

Yaesu FT-7B Manual de usuario

Kenwood

Kenwood ProTalk TK-3201 Manual de usuario

Texas Instruments

Texas Instruments TLK10232 Manual de usuario

Mizuho

Mizuho MX-2 Guía del producto

Kenwood

Kenwood TK-3180 Manual de operación y mantenimiento

Blitz

Blitz MJ-398U Manual de usuario

Utilicom

Utilicom LongRanger 2050 Manual de usuario

Standart

Standart HX290UKA Manual de usuario

Altronix

Altronix Pace1PTM Manual de usuario

Kirisun

Kirisun PT2208 Manual de usuario

ELECRAFT

ELECRAFT KX2 Manual de usuario

Zodiac

Zodiac K3 Manual de usuario

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manual de usuario

Kenwood

Kenwood TK-2217 Manual de usuario

Siemens

Siemens PSO 4000 Manual de usuario

Kenwood

Kenwood TS-590SG Manual de usuario

Midland

Midland G8E-BT Manual

ComNav

ComNav Mariner X2 Manual de usuario