Icom IC-M424 Manual de usuario

IC-M424

VHF MARINE TRANSCEIVER

HI/LO

MIC

TO ANTENNA

COMMANDMICIV

DC Power Connector

+ (Red)

– (Black)

AF Out Leads

Orange:Public Address Speaker (+)

Gray:Public Address Speaker (–)

Blue:External Speaker (+)

Black: External Speaker (–)

NMEA Leads

Brown:Out- Talker B (Data-L) (–)

White: Out+Talker A (Data-H) (+)

Green:In- Listener B (Data-L) (–)

Yellow:In+ Listener A (Data-H) (+)

HM-195

COMMANDMICIV™

Handset

HM-196

Handset

(non-removable)

*

*

* For more details about connections please review

pages 83 & 84 in the Instruction Manual.

1Represents the NMEA In/Out Leads.

2Represents the AF Out Leads.

OPC-1540

20ft of cable

OPC-1541

20ft of cable

OPC-478UC

Programming

Cable

OPC-980

Programming

Adapter Cable

**

©2015 Icom America Inc. The Icom logo is a registered

trademark of Icom Inc. 42070

1

1

2

2

Wires For Standard

External Speaker (4 Ω)

©2015 Icom America Inc. Page 2

Icom America, Inc.

12421 Willows Rd NE

Kirkland, WA

Connecting a GPS to Your Icom M324/M424 radio

On the back panel of your radio, there is a connector with four colors: brown, white,

green, and yellow. The yellow and green wires connect to your GPS.

Connections

Radio

GPS

NMEA in + (yellow) →NMEA / Data out

NMEA in – (green) →NMEA / Data ground

GPS Example Connections

You will need to solder the 2 wires to the NMEA wires from your GPS. For more

specific information, consult the individual instruction manual from the GPS

manufacturer.

Garmin GPS

©2015 Icom America Inc. Page 3

Icom America, Inc.

12421 Willows Rd NE

Kirkland, WA

Raymarine GPS

Note: When using some Raymarine equipment you may need to connect your Icom

radio directly to the Raymarine GPS itself, not through a repeated port from other

equipment, such as a plotter. This ensures that the proper NMEA sentence passes to

the radio.

Standard Horizon GPS

©2015 Icom America Inc. Page 4

Icom America, Inc.

12421 Willows Rd NE

Kirkland, WA

Troubleshooting Your GPS Connection

•Your Plotter/GPS receiver must be capable of sending the proper sentences

(listed below) set for NMEA 0183 (Check your Plotter/GPS instructions for

information.)

•Verify that the plotter/GPS device is sending GPGGA, GPGLL, GPRMC, GPVTG, or

GPGNS sentences. (Check Plotter/GPS Instructions.)

•If you are still not receiving latitude and longitude, you can try setting the plotter

to send just a single GPGGA sentence.

•Have a technician check the plotter/GPS using test equipment to verify it is

sending the GPS sentence.

•Check the solder points on the radio and plotter connectors. Some connectors are

very small, increasing the likelihood of solder bridging.

Tabla de contenidos

Otros manuales de Transceptor de Icom

Manuales populares de Transceptor de otras marcas

Yaesu

Yaesu FT-7B Manual de usuario

Kenwood

Kenwood ProTalk TK-3201 Manual de usuario

Texas Instruments

Texas Instruments TLK10232 Manual de usuario

Mizuho

Mizuho MX-2 Guía del producto

Kenwood

Kenwood TK-3180 Manual de operación y mantenimiento

Blitz

Blitz MJ-398U Manual de usuario

Utilicom

Utilicom LongRanger 2050 Manual de usuario

Standart

Standart HX290UKA Manual de usuario

Altronix

Altronix Pace1PTM Manual de usuario

Kirisun

Kirisun PT2208 Manual de usuario

ELECRAFT

ELECRAFT KX2 Manual de usuario

Zodiac

Zodiac K3 Manual de usuario

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manual de usuario

Kenwood

Kenwood TK-2217 Manual de usuario

Siemens

Siemens PSO 4000 Manual de usuario

Kenwood

Kenwood TS-590SG Manual de usuario

Midland

Midland G8E-BT Manual

ComNav

ComNav Mariner X2 Manual de usuario