Icom IC-F52D Manual de usuario

– 1 –

ACCESSORIES GUIDE

VHF/UHF DIGITAL TRANSCEIVERS

Iç-F52D Thank you for choosing this Icom product. READ

ALL INSTRUCTIONS carefully and completely

before using this product.

This guide describes about the IC-F52D/IC-F62D’s

accessories and option details.

Supplied accessories

Iç-F62D

Battery pack Belt clip Connector cover

(with a screw)

NOTE:

• Some accessories are not supplied, or the shape

is different, depending on the transceiver version.

• Conrmbothbatteryslidinglocksarelocked

in place, when attaching the battery to the

transceiver. Both sliding locks make a ‘click’ sound

when locked.

Attaching accessories

DFlexible antenna

Connecttherequiredexibleantennatotheantenna

connector.

CAUTION:

• DO NOT carry the transceiver by holding only the

antenna.

• DO NOT connect an antenna other than those

listed in the INSTRUCTIONS.

• Transmitting without an antenna may damage the

transceiver.

DBattery pack

CAUTION: DO NOT attach or detach the battery

pack when the transceiver is wet or soiled. This may

result in water or dust getting into the transceiver/

battery pack and may damage the transceiver.

To attach:

1. Slide the battery pack in the direction of the

arrow. (q)

2. Push the battery pack until the battery sliding

locks make a ‘click’ sound. (w)

To detach:

1. Push both battery sliding locks in the direction of

the arrow. (z)

• The battery pack is then released.

2. Lift up to detach the battery pack. (x)

NOTE: Keep the battery pack terminals clean. It’s a

good idea to occasionally clean them.

Battery sliding locks

Battery pack

– 2 –

Attaching accessories (Continued)

DBelt clip

To attach:

1. Remove the battery pack from the transceiver, if

it is attached.

2. Slide the belt clip in the direction of the arrow until

the belt clip is locked and makes a ‘click’ sound.

BE CAREFUL! DO NOTbreakyourngernail.

To detach:

Lift the tab up (q), and slide the belt clip in the

direction of the arrow (w).

Belt clip

DConnector cover

CAUTION: BE SURE to attach the connector cover

when an optional device is not in use. Otherwise the

terminals of the multi-connector may be shorted by

a metal object, or become rusty by water intrusion.

This could damage the transceiver.

To attach:

1. Attach the connector cover over the multi-

connector. (q)

2. Tighten the screw. (w)

To detach:

1. Remove the screw. (z)

2. Detach the connector cover, and then connect an

optional device. (x)

– 3 –

Options

Belt clip

Turn OFF the transceiver

before attaching or

detaching the microphone

NOTE:

•NEVER immerse the connector in water. If the

connector becomes wet, BE SURE to dry it before

attaching to the transceiver.

• The microphone element is located at the top

left of the speaker microphone, as shown in the

illustrationabove.Tomaximizethereadability

of your transmitted audio, hold the microphone

approximately5to10cm(2to4inches)fromyour

mouth, and then speak at your normal voice level.

To attach:

Attach the connector of the speaker microphone to

the multi connector on the transceiver and tighten the

screw.

[PTT]

[Emer]

Speaker

Microphone

Earphone

jack

Turn OFF

Screw

Coin

CAUTION: Firmly attach to the multi

connector, but do not overtighten.

A loose connection will allow water

intrusion into the connector.

Over-tightening the connection can

damage the transceiver.

NOTE: KEEP the connector cover attached to the

transceiver when the speaker microphone is not in

use.

Water will not get into the transceiver, even if the

cover is not attached. However, the terminals (pins)

will become rusty, or the transceiver will function

abnormally if the connector becomes wet.

You can connect

an earphone

(user supplied)

to the earphone

jack on the

microphone.

DHM-222 speaker microphone

–4–

DMB-136 belt clip

Belt clip Base clip

To attach:

1. Detach the battery pack, if attached.

2. Slide the base clip in the direction of the arrow

until the clip locks and makes a “click” sound.

3. Attach the battery pack to the transceiver.

Base clip

Battery pack

4. Clip the belt clip on your belt.

5. Insert the transceiver upsidedown into the belt

clip until the base clip is fully inserted in the

groove.

NOTE: Holdthetransceiverrmlywhen

inserting the transceiver into the belt clip.

6. Once the transceiver is locked in place, it swivels,

as shown below.

NOTE: If the transceiver has been accidentally

dropped and the base clip is scratched or

damaged, the transceiver may not be properly

attached to the holder or swivel.

Once the transceiver is locked on place,

itswivels360degrees.

Options (Continued)

To detach:

1. Turn the transceiver upsidedown in the direction

of the arrow and pull it out of the belt clip.

NOTE: Holdthetransceiverrmlywhen

removing the transceiver from the belt clip.

2. Detach the battery pack. (p. 1-3)

3. Lift up the tab on the base clip (q), and then slide

the clip in the direction of the arrow (w).

BE CAREFUL! DO NOTbreakyourngernail.

wBattery

pack

– 5 –

Options (Continued)

DBC-226 desktop charger

Chargingtime:approximately2.7hoursfortheBP-290

LTo connect the power adapter

to the charger, remove the

charger’s left cover.

Turn OFF

BC-226

Power adapter*

(BC-228)

Battery pack

Connecting BC-226 together

You can connect up to 6 BC-226 together.

1. Remove the charger’s right cover. (q)

2. Snap the DC power plug to the another charger’s

DC power jack. (w)

WARNING: DO NOT connect more than 6 chargers

together. It may result in an electric shock, cause a

re,overheating,ordamagechargers.

Status indicator information

Light color Status

Orange Charging

Green Charging is completed.

Blinks orange and green Charging failed. It may have

some problems.

Fuse replacement

Ifafuseblows,ndandrepairthecauseofthe

problem. Then replace the damaged fuse with a new,

adequately rated fuse.

Fusetype:5A/58V(lowprolemini blade fuse)

NOTE:

• The transceiver MUST be turned OFF while charging. Otherwise:

- The battery will not be charged properly.

- The battery life may be shortened.

• Do not transmit while charging. When you need to transmit, remove the transceiver from the charger, and then

turn ON the power.

• If the battery pack does not properly charge when it is attached to the transceiver, remove it from the

transceiver and insert only the battery pack into the charger.

Status indicator

* May not be supplied, or the shape may be different, depending on the version.

CAUTION: Readthe‛Batterycaution’and‛Chargingcaution’

on the PRECAUTIONS before using the charger.

NOTE: Remove the fuse using the needle-nose pliers.

Fuse

Battery pack + Transceiver

– 6 –

A7397-8EX

©2017IcomInc.

1-1-32Kamiminami,Hirano-ku,Osaka547-0003,Japan

Options (Continued)

 BC-226 Specications

• Dimensions(projectionsarenotincluded.): 106.5(W)×49(H)×78(D)mm,

       4.2(W)×1.9(H)×3.1(D)inches

 When6chargersareconnectedtogether 542(W)×49(H)×78(D)mm,

       21.3(W)×1.9(H)×3.1(D)inches

• Weight(approximately):   120g,4.2oz

 When6chargersareconnectedtogether 640g,22.6oz

• Chargingtemperaturerange:  15˚C~40˚C,59˚F~104˚F

• Powersupplyrequirement:  12~16VDCorthespeciedpoweradapter(BC-228)

Otros manuales para IC-F52D

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Transceptor de Icom

Icom

Icom IC-F70T Manual de usuario

Icom

Icom IC-02A Manual de usuario

Icom

Icom IC-F3S Manual de usuario

Icom

Icom IC-41W Manual de usuario

Icom

Icom IC-737 Manual de usuario

Icom

Icom IC-FR4000 Series Manual de usuario

Icom

Icom ic-2730A Manual del propietario

Icom

Icom M506 31 Manual de usuario

Icom

Icom IC-A120 Guía de instalación

Icom

Icom IC-F1721 Manual de usuario

Icom

Icom IC-M505 Manual de usuario

Icom

Icom IF3061S Manual de usuario

Icom

Icom IC-7800 Manual de usuario

Icom

Icom IC-A200 Manual de usuario

Icom

Icom IC-3SAT Manual de usuario

Icom

Icom IC-M36 Manual de usuario

Icom

Icom ID-880H Manual de usuario

Icom

Icom IC-910H Manual de usuario

Icom

Icom IC-F1000 series Manual de usuario

Icom

Icom IC-7300 Manual de usuario

Icom

Icom VHF MARINE TRANSCEIVER IC-M501EURO Manual de usuario

Icom

Icom IC-7000 Manual de usuario

Icom

Icom IC ?2A Manual de usuario

Icom

Icom NXDN IC-F5400D SERIES Manual de usuario

Manuales populares de Transceptor de otras marcas

Yaesu

Yaesu FT-7B Manual de usuario

Kenwood

Kenwood ProTalk TK-3201 Manual de usuario

Texas Instruments

Texas Instruments TLK10232 Manual de usuario

Mizuho

Mizuho MX-2 Guía del producto

Kenwood

Kenwood TK-3180 Manual de operación y mantenimiento

Blitz

Blitz MJ-398U Manual de usuario

Utilicom

Utilicom LongRanger 2050 Manual de usuario

Standart

Standart HX290UKA Manual de usuario

Altronix

Altronix Pace1PTM Manual de usuario

Kirisun

Kirisun PT2208 Manual de usuario

ELECRAFT

ELECRAFT KX2 Manual de usuario

Zodiac

Zodiac K3 Manual de usuario

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manual de usuario

Kenwood

Kenwood TK-2217 Manual de usuario

Siemens

Siemens PSO 4000 Manual de usuario

Kenwood

Kenwood TS-590SG Manual de usuario

Midland

Midland G8E-BT Manual

ComNav

ComNav Mariner X2 Manual de usuario